The Wempe Einheits-Chronometer model · verification · 12 November 2026 · the Hamilton's: would a chronometer made to it run?, the model against real Model 21s
The Wempe Einheits-Chronometer: does the model hold to its drawings, and would it keep time?
The model of the German standard marine chronometer of the 1940s is built from Wempe's works drawings, each sheet as last revised. Two questions follow from that. Does the model hold to its drawings: is every part a closed solid where its sheets put it, clear of its neighbours, counted against the drawing list, every figure read and every guess said to be one? And would a chronometer made to those drawings keep time: does the escapement run, does the fusee even the spring, does the energy budget close, do the teeth and springs hold, does it stay in rate from cold to hot and at sea, and does it pass the trial its Soviet copy, the 6MX, was made to pass? Every figure below comes from a script in the repository, run on the model's own numbers, and is shown as the script prints it: ok a check that holds, ~~ one the script reports but doesn't fail on (an open question, or the strong end of a range only), !! a failure.
Approach
The Wempe's checks are the Hamilton's, pointed at the second model (--model wempe), with tools of their own where the two chronometers differ: the
Wempe's detent carries a gold passing spring on its own horn, its fusee's force was measured by its makers on the drawing itself, its balance is a cut bimetallic one
with movable masses, and its hairspring is a helix with drawn terminal curves. The tools run on the same files the page draws from (js/escapement.js,
js/escphys.js, the shared makeEsc), so what they check is what the page shows.
| # | Question | Method | Script |
|---|---|---|---|
| 1 | Is every part a sound solid, clear of its neighbours, and on the drawing list? | Closed-mesh tests, a 0.05 mm voxel interference check through the escapement's phases and the wind, a screw and loose-end audit, the Spread view's clearance, every part against bom.json | solids.py, fine.py, audit.py, exploded.py, bom.py |
| 2 | What do the drawings say, and what had to be guessed? | The sheets transcribed figure by figure with how sure each reading is; the readings corrected on the sheets; the estimates listed | References/wempe/, the model's README |
| 3 | Does the escapement run, and does it run in time as the averaged model says? | makeEsc solved from the layout drawing; the escapement integrated beat by beat; the detent as a frame of beam elements | wempe_escapement.js, dynamics.js, tripping.js |
| 4 | Does the drawn fusee even the mainspring as its makers measured? | The spring solved for its shape at every quarter turn, fitted in length and set to 05 06_20's force | wempe_mainspring.py |
| 5 | Is there energy enough, from spring to balance? | Every loss from the parts, the balance's damping from its parts; the swing the drive can hold | wempe_physics.js |
| 6 | Do the gears mesh, and how exactly must the holes be placed? | Tooth-by-tooth contact on the page's own outlines; the train in time; each mesh's depthing window | gearing.js |
| 7 | Will the loaded parts hold, fully wound? | Each part's stress against its material's published range | wempe_strength.js |
| 8 | Does the drawn hairspring keep the balance free of side forces, and isochronous? | Phillips' conditions on 05 03_7's curve; the spring at large swings as an elastica and as beam elements | wempe_hairspring.js |
| 9 | Does the bimetallic balance compensate, and where must the masses sit? | The rim's quarters as bimetal cantilevers, every part weighed; the secondary error | wempe_thermal.js, wempe_thermal_frame.js |
| 10 | Does the case hang level and stay so at sea? | The case and ring weighed on the model, levelled as 05 01 says, run in a seaway | massprops.py, gimbals.js |
| 11 | Would it pass the 6MX's trial, and what would a navigator carry? | The TU's 35-day trial and a 60-day voyage, Monte Carlo over the rate's parts | wempe_errorbudget.js |
| 12 | Would a Wempe made to its drawings work, and how is it tested? | The unsized parts' tolerances from the escapement's swing over the wind; the bench's tests with their pass figures; 2,000 movements made to tolerances, as made and after the bench | wempe_tolerances.js, wempe_bench.js, wempe_montecarlo.js |
| 13 | How does the escapement compare with a period text's rules? | Each proportion against Watch and Clock Escapements (1904), Ch. III; reported, never judged | keystone.js |
| 14 | Is the balance's damping right? | A running 6MX's swing read frame by frame off a video, fitted with the Wempe's balance equation | wempe_swing.py, wempe_startup.js |
Units: millimetres and micrometres (µm), newtons, seconds a day (s/d, + gaining). The swing is the balance's amplitude, each way. The model runs its balance at the train's half second; the drawn hairspring with the weighed balance gives a little less (section 8), which a maker times out. A rate of 4 s of time is a mile of longitude at the equator. Each tool's whole output is under its checks ("its whole output"), as it printed it when this page was built.
1. Geometry: does the model hold to its drawings?
The model is a set of closed solids, as a CAD model is, so it can be checked as one. Five browser checks open the Wempe's page itself and measure the parts as built.
Solids: every mesh closed (no open edge), consistently wound and with a positive volume, as loaded and in a section with Moving parts only. Fine
interference: every part voxelized at 0.05 mm in states (the escapement through its unlocking, impulse and return; the train at many
phases; the fusee from full wind through winding to run down), every pair of parts that overlaps reported; only the contacts listed below, each with its reason and a
size it may not exceed, may overlap. The screw audit: screws overlapping, screws with nothing under their heads, arbor and pin ends sitting in nothing, faces
lying on each other, parts touching nothing, in the movement and in the case and box, against the leftovers expected. Exploded: the Spread view lifts each
part on its own path; no two may pass through each other. The parts list: every line of bom.json, transcribed from the drawing list, counted on the model's
pieces, and its relations measured on the built meshes.
The contacts that are meant
Every overlap fine.py finds is one of these, each a joint the drawings make that a turned or extruded solid can't show cut: a screw in a thread not cut across
a turned body, a pressed fit drawn at its fit's middle, the chain in its groove. The measured column is the largest overlap over all the states, against the size it may reach.
The audit's expected leftovers
The parts list
2. The sources: what the drawings say, and what was guessed
The model's evidence is, in order: the works drawings (sheets of Wempe's, as published by the Deutsche Gesellschaft für Chronometrie, each read as last revised); the coloured section of the whole movement; photographs of real German movements (Wempe 3955 above all); and, for what only the Soviet copy shows, the 6MX's own documents. None of them is reproduced here: they are other people's work, cited and linked from the model's page. The model's README says for every figure which sheet it is from and how sure the reading is; below is that record in numbers.
The sheets
References/wempe/README.md's catalogue
(wempe_essaydata.js).The transcription
Each group's sheets were transcribed into a table of every figure, with its tolerance or fit and how sure the reading is (sure: legible, likely: legible with one reading taken over another, unsure: faint or partly hidden). Where a number mattered, the sheet itself was cropped and enlarged, and the readings were corrected there (below).
References/wempe/transcriptions/.Readings corrected against the sheets
Checked on the sheets while building, where the transcription read a figure or a feature wrongly ( readings; the transcriptions are left as written):
The readings corrected
- The parts audit's corrections (3 November 2026;
WEMPE-PARTS-LEDGER.md, every finding's outcome inPLAN-wempe-parts-fixes.md):- The detent's horn keeps 1436's 0,25 (0,22) to its tip, where it was ground to 0.05, an estimate of "Anschrägen"; now bevelled in plan only.
- The detent block's banking screw has its hole centred on the upright, as 05 04 01-4 draws it; it stood 0.15 under, after photographs of other makers' blocks. Its estimated head is now Ø 3.15, Lange 5177's, to clear the detent.
- The pillars' lead is 5°, the figure 05 08 00-1 prints and the only one its 1,1 and 4,3 agree with (6° before).
- The set-up ratchet, the barrel arbor's square and its hook are one unit: a tooth's tip on the square's flat (05 07 00-3), the hook 15° from that flat's normal (05 07 02). So the set-up, 05 06_20's 3/4 turn, falls back to the first face on the click: 0.7125 turn.
- The box's strap screws are countersunk, as 51 00_5's "Din 97" fixes them.
- Five frame sizes drawn at their tolerances' tops, now at their middles (29 October 2026, the owner's choice, found by the recipes' check, PLAN-recipes.md): the barrel bridge's thickness 3.32 −0.04 (05 08 05-1) drawn 3.30; the fusee bush's flange Ø 13.2 −0.2 (05 08 01-2) Ø 13.1; the dust bush's body Ø 13.1 −0.2, collar Ø 15.1 −0.2 and neck Ø 9.7 −0.2 (05 08 01-3) Ø 13.0, 15.0 and 9.6. The model's convention draws a toleranced size at its middle, as it does the plates, the pillars and the fits; these five were drawn at their figures' tops. The collar at 15.1 was more than its Rundmessing 15 gives; at 15.0 it is the bar's own. With them: the dust bush's bottom keeps its figured 0.5 bearing ring inside the 0.3 × 45° chamfer (estimated), so the ring runs Ø 11.4-12.4; its collar's flat stays flush with the body (14.1, read 14.1 −0.2, at its middle 14.0 from the far side); the cork ring's bore stays the neck's + 0.01 (Ø 9.62).
dims.js(WD.BB, FB, DB, CORK) holds each with its tolerance. - The up-and-down wheel's "35,3 −0,2" (05 02_11; 28 October 2026, the second drawing check's F3): its arrows lie on the outermost circle, which is the tip circle (its ratio to the rim's inside 1.206 against D/28.2's 1.217 and 35.3/28.2's 1.252; an overlay lays the model's tips on it), so 35,3 is the blank's diameter, as 05 02_7's "21,5 gedreht" and 05 02_9's "20,2 gedreht" run over their tables' D; the tips are the table's D 34,33, as built (a 35.3 tip would cut 0.45 into the pinion's root at 18.4).
- The dial's seconds hole "17" (05 02_12; the same, F7): its arrows are drawn outside, pointing in to extension lines tangent to the hole (the small-hole convention, the hole drawn oversize at about 2.0), so the hole is Ø 1,7, as built round the collet's Ø 1.5; not 2.2 (Lange's 1453/A).
- 05 02_1's framed 2,6 and 3,2, and its "2,8" (the same, F1, F5, 7-M5): the 2,6 is the dial's top face to the hour hand's top and the 3,2 the dial's top face to the minute hand's underside, at the cannon tube's square's shoulder (the transcription had them on the cannon's fit and the dial's underside); the "28°" by the fusee arbor is its Ø 2,8 in the plate. 05 02_06's "4,3 +0,1" runs to the pinion's underside, and 05 02_1's "0,6" is the change wheel's collar (F2, F4): the code had them right; the transcription is corrected.
- The winding square "3,1 r6" (28 October 2026, the second drawing check's 5-M1): 05 06 04-1's figure after "3," is the hand's flagged 1 (the 1 of "+0,015" beside it is drawn alike), and +0.023/+0.015 is r6 for 3-6 mm; with 3.12 at the root the 1:100 over the square's 20.3 gives the sheet's own 2,92 at the point. Read "3,17 r6" until then (the transcription's), 0.05 too large. The dust plate's "3,1 □ H7, Kegel 1:100" then wedges 1.0 from the root, where 05 06_1 dimensions it (built 4.0 off, its hole straight 3.134 and loose, until then: 5-M2); the key's socket (05 01 02-3: 3.1 +0.05, drawn 3.15) takes the square anywhere along it.
- The body's sixth "Grund" radius, 10,07 (28 October 2026, the second drawing check's 5-M13, closed): both issues of the body (05 06 04-2 and 02-1) read 10,07, the 7's stroke matching the column's other 7s; 05 06_20 reads 10,04, but it is a steel fusee's curve ("Schneckenkurve von Stahlschnecke"), not this part's sheet. Built 10.07; the 0.03 recorded.
- The 1941 arbor's square end (28 October 2026, the second drawing check's 4-M5, kept). 0207's section ends the square 10 past the barrel bridge's outer face, rounded, with no point; the model's as first drawn runs its sides to y −35.4 and a point to −37.32, 1.65 further. Kept: 020704-1 (the arbor's own sheet) gives 7 + 22,2 + 15 = 44,2 overall with a turning centre on the square's end, and Wempe 3955's photograph (
4_Wempe_3955_N.jpg) shows the point, 2.2 ±0.3 high, its sides ending 13.1 from the shoulder; 0207's ends are schematic (its plate end a ball where 020704-1 has a centre). - The chain's top hook's "30°" (28 October 2026, the second drawing check's 4-M20, kept with its reason). 05 07 04 draws the nose's inner edge about 50° to the chain's line (45° to its drawn throat wall, which leans 5°: the comparer's and the refuter's readings; 53-56° read again at 6×), and its "30°" arc is centred on the seat with one arm on the throat wall. The sheet's own figures leave no room for that edge: with the seat r 0,4 at 3,5 from the rivet (its figure, drawn at 3.0), the throat wall 1,8 in from the outer edge and the nose ending 2 from the rivet, 2.5 across, the only line from the nose's end tangent to the seat on the throat's side lies at 30.1° to the chain's line (at 50° the seat would have to stand 2.6 from the rivet, at 45° 2.76). So the figures, with their 30° read to the chain's line, are built; the drawing's steeper edge goes with its seat drawn at 3.0, before the bold "3,5" (likely a revised figure). An edge drawn at 50° would break the 3,5 or the 2.
- The 1946 staff's rollers, and with them the escapement's heights as last revised (27 October 2026, from Unresolved, the owner's question on the banking screw). 05 04 02 (29.5.46) dimensions from the hub's flange top: the hub's neck to 4.1 +0.05, then a step to 5.6, then the lower arm. Measured on the sheet at 17.6 px/mm (its Ø 1.65 at the top, 29 px), the step is 28 px wide (Ø 1.6-1.65) and the arm under it 21 px (Ø 1.2); a Ø 2.14 would be 38 px. The step is therefore the "1,65 s6" seat, its leader drawn to it, and the "2,14 +0.01" is the hub's bore at its foot. The impulse roller (02 04 02: 1.6 thick, bored 1.627/1.65 on 1:70) sits on that seat from the hub's end, and the discharge roller under it on the Ø 1.2 r6. Four sources agree:
- 05 03_3.2, the production staff of 13.3.65: its Ø 1.65 −0.02 seat 1.6 long, from 4.1 to 5.7.
- The coloured section, which numbers its staff and hub 05 04 02-1 and -2: the impulse roller directly under the hub's end, about 4.2 under the flange top, the discharge roller under it, at 9.4 px/mm.
- 05 04_1's "4,1 bis Unruhauflage".
- Wempe No. 9166 of 1972 (Uhren-Hidding's archive,
uhren-hidding.de/326-xxlarge/marinechronometer-chronometerwerke-wempe.jpg, a side view under the balance): the escape wheel's teeth right under the top plate, the detent along the plate, the block's upright under it with the slotted head at the stone (sure in layout); its balance rim close over the plate, about 0.3-0.5 by the rim's 3.8, as the model's 0.45 (likely). Wempe 9411 (Auktionshaus Stahl 113478) looks the same at low resolution. The model had read a collar Ø 2.14 from 4.1 to 5.6 with the impulse roller under it, which put the rollers 1.5 lower than every other source. To meet them it put the escape wheel 1.5 lower (its arbor's ends 0.49 and 0.06 inside the plates), read the block's side view in third angle (the upright flush with the plate, the detent's foot 3.2-5.2), left the banking screw a shank bearing on nothing, and listed the conflict as Unresolved. Now the rollers stand 0.32-3.52 under the plate and the escape wheel's teeth 0.4-1.8, its arbor's ends 1.98 and 1.55 in. The block is 05 04 01-4 read in first angle as the sheet reads, built as the escapement of 1943's, its banking screw whole and the pipe on its head. The detent's foot is at 1.3-3.2, its pipe 1.9-3.8, the lower endstone 1.5 down a window in its setting. The balance, its staff's other figures and every plan stay; makeEsc and the physics are planar, so the escapement's timing doesn't move with the heights (the bodies' inertias do, slightly:wempe_inertia.json). The owner chose not to keep the old reading as a version (27 October 2026).
- The detent's blade flush toward its block (27 October 2026, the owner's choice "Adopt and refit"; .1436's left view and 10-2's "linke Seite": sure): the foot, spring, square and the blade's thicker part are centred 0.11 ((0,50 − 0,28)/2) off the blade's line toward the wheel, the blade, pipe and stone flush with their face toward the block (the blade centred until then). The block's offset 0.30 → 0.19 (ACR 7.49), so the stone lands 18.77 from the block's screw row (18.73), the detent line turns 0.15°, its flexure lies 0.11 off the stone's line, the gold spring's bending point 0.11 over. The discharge stone's reach (estimated, set so the stone is lifted 0.07 past the lock) takes the gold spring's tip's slide out along the blade as the detent turns about the offset flexure, DOFF times the turn (2.6 µm): RD 1.578 (1.5754 without it, which lifted the tip 12 µm less, let the stone fall back 0.6° sooner onto the tooth's tip with a weak drive, makeEsc's swing 78° at 90 %, and held the swing on the stone's blow's step). The detent weighed about the offset flexure: ID 8.23 (8.16), the 6MX's 8.01 (7.94). The swing 197.1° at 12 h (195.1°), 192.4-202.3° over the wind; HS −0.483 at it (−0.470). Two cross-checks widened, the owner's choice (The physics pass).
- The drawings check's open items on the balance and escapement, settled (27 October 2026, from Unresolved; each sheet read again, enlarged):
- The collet's bore (05 03 02-2): its 1,6 H7 on 1:70 to (1,55), the 1943 collet's, against the 1946 staff's seat (1.58 to 1.65 s6): the taper built, the size the seat's (Ø 1.647 to 1.604; straight 1.648 until then), since 05 03_5's 13,4 and 0,75 put the collet on the arm, where a 1.6 bore would stand 3.15 higher.
- The staff's lower pivot (05 03_3.2): 12,6 −0,02 below the seat built (12.59; 12.83 until then, the lug's endstone placed 0.95 inside its face by estimate): the only finished figure for it, as its 13,0 is for the upper, and the coloured section's endstone 10 px (1.06 ±0.11) inside the lug's face lies between the two. Its cones hollow: the detail draws both flanks concave with a "6" on a radius's leader; built R 6 (0.09 deep).
- The block's upright foot (05 04 01-4): read convex in the drawings check; its arc, 35 rows traced on the front view at 17.1 px/mm, fits a circle r 2.96 whose centre lies in the air (rms 0.3 px), a cove, so "3 r" is its radius: from a step 0.35 out 2.5 over the base (the "15") to 2.0 out and 0.4 over it (the "0,4"), then straight down, flush with the 6.5-deep part's end (the hidden line under it). Built so as last revised and in 1943 (a cove r 3 tangent to both, and r 2, until then); the CWW's block (10_Vergleich_CWW-6MX_Gangfeder_mit_Kloben.jpg, left) shows the cove. The 1943 block's end face bored as the others (its M1 on 20 sides, which fusee.js's bore closes there).
- The block screw 23,8 from the wheel (05 04_1, 3.2.40) against the top plate's table's hole 13 at 23.41: Wempe 3955, which carries the 1941 block, has its fixing screw's head 23.36 ±0.15 from the escape wheel's endstone setting (2_Wempe_3955_A.jpg: 205.8 px at 8.81 px/mm, the head's centre put back 2.4 to the plate's face): the table is the plate as drilled; kept.
- The stud's round point and pin hole (05 03 02-3): both kept. The point's "0,8" (a diameter, drawn about Ø 0.55) is the blank's: the facets ground to the section's knife edge leave no metal for it, and Wempe 3955's point shows under Ø 0.3. The hole Ø 0.7, drilled "bei Montage der Spirale" (27 October 2026; until then read as a pin's hole beside the spring in a slot the sheet doesn't draw): the end view's circle, 0.72 from the end and 0.36 from the upright's middle toward the axis, 3.46 from the staff, takes the spring's end itself with its Ø 0.22 pin, as the collet's Ø 0.8 takes the inner end 3.5 from the staff.
- The fusee body's place on its arbor, and its large face re-turned (25 October 2026, the per-part audit; from Unresolved). 05 06 04 as revised 2.3.48 (05 06_3.2), measured on the sheet (line centres on profiles across each line, 12.02 px/mm along the axis by the arbor's 19.7 and its collar and step, 7.9 + 3.1; the scan turned 0.0035 rad): "13,7 −0,1" runs from the large face (its extension line down from the flange's outer corner) to the end of the arbor's Ø 6.1 step (its extension line at x 601.7), drawn 13.61; "0,5 +0,05" from the face to the click wheel's face (its extension line down past the wheel), drawn 0.60; the bracketed (12,3) from the face to the small end, drawn 12.17, and (1,6) to the second rib's outer face, drawn 1.79, both "in Klammern gesetzt" by the revision, which made 0,5 and 13,7 the governing figures; "33∅ +0,1" between the 45° chamfer's mouth (Ø 29.8) and the flange's rim, and "5°" an angle at the flange's outer corner with a leg on the 33's extension line; "(a) Fläche muß schlagfrei zur Welle laufen". The face line is one straight line (no step at Ø 33: a 0.25 step would be 3 px). So the large face is re-turned true on the arbor at assembly, all of it, 0.2 deep (the click wheel, 0.7 under the blank's face, 0.5 under the re-turned one), with a 5° fall outside Ø 33 (0.114 at the rim), and the body pressed on so that face lands 13.6 from the step's end; the groove and its end N, cut on the part before, keep their places from the small end, the first rib 0.56 and the ribs 1.8 over both. Where the sheet draws the rest: the small end 1.29 from the step's end, the recess floor 11.24, the arbor's collar starting 0.25 inside the body's bore (the model now 1.25, 11.1 and 0.1 inside; until then 0.91, 10.76 and 0.24 outside). The stack under it comes down to meet it by re-turning the Vorreiber's face a, its own sheet's assembly note (2.76, the fusee wheel 2.385 off the plate as the coloured section's 2.4), and the cover plate lies under an empty 0.425 of the J-K recess as the coloured section draws it (0.5); the stop pin's 1.85 off the coloured section then reaches just past the stop bar's thin end, as the section draws it. Rejected: the face inside Ø 33 re-turned with the flange left standing (the flange 0.2-0.39 into the maintaining ratchet's plate, which runs under the whole face to Ø 37.2, and a step the sheet doesn't draw); the groove measured from the re-turned face (it is cut before). Until 25 October 2026 the face 13.46 from the step, not re-turned, the click wheel 0.7 under it (Unresolved's 0.75 was a slip), the body 0.34 nearer the top plate. Likely; a sharper scan of 05 06 04 would settle the figures to better than the scan's ±0.1-0.2.
- The stop bar's slot's two depths, and the flange's ribs (31 October 2026; the fusee body checked feature by feature against 05 06 04-2,
tools/wempe_fusee_check.py). Schnitt C-D writes "1,1+0,05 tief" in the slot's half toward the chain's pin A (the bar's upper end) and "1,5+0,05 tief" in the other half, each between the small end's recess (Ø 15 × 1,6, deeper than both) and the hub's rim; the superseded 02-1 writes its 1,2 and 1,6 in the same places. So the upper end's half is 1,1 deep from the recess out, and the dashed arcs across it are the groove's top turns hidden under its floor (a step in that floor would be seen from the section's side, a solid line); the lower end's half shows the turns solid and unhatched, the window. It was read as 1,5 deep on the upper side out to the dashed arc (r 9.30, and a straight step at u 8.0 before), so the bar's full thickness ran to u 3.4; now the bar is 1.45 only inside the recess (to u 0.8, estimated) and 1.05 beyond. The flange's ribs: the lathe's rows 0.04 apart put the slot at A 0.909 wide against 0,87 +0,01 and the second rib 0.323 against 0,37; swept with the faces as fixed corners, 0.870 and 0.370, 2.000 over both against "2 ±0,02". The "2" at C-D's upper left, unassigned until then: the chord on the hub's rim from the slot's far wall's end to the line where C-D's hidden arcs begin (137° from 3 o'clock seen from the small end, A at 90°; scaled 2.2-2.5): likely where the top turn's run-out starts; N's own leader (145.8°) agrees with the model's N (146.3°), which stays. - The case's last open readings of the drawings check (27 October 2026, batch 10's): 51 00 10's section figures the handle's ends "6" and its middle "12,5" off the side panel and the finger recess "10" deep (the handles built 10 off with 3 thick ends, the recess at its scaled 10.5); 51 00 11's 1940 key figures its stem "32" out of the body (built at the traced 31.74); 05 01 Schnitt A-B draws the ring bracket's screws through the ring to its inside (built 2.75 into it); 05 01 02-3's tube end is sunk 60° "1 +0,2" (left out) and P. 51 00 02-2's tongue has its hole sunk 0,5 × 45° and its far end thinned 0,2 over 7 (left out). Each built as drawn. The tube's relief, read as Ø 4.2 at 21° in the check, measures Ø 4.8 at 9.72 px/mm (47 px across the end): the model's estimated Ø 4.6 at 15° kept. The bowl's floor, whose bottom and turned wall stood 0.01 apart (a dotted ring in Edges), is one closed solid.
- The bezel screws onto the bowl (24 October 2026, at the owner's word, with Kirov-Poljot 24020's and a 6MX's photographs of the threaded rim): 05 01 01 marks a thread in the bezel's skirt (its hidden zig-zag), which the model had left plain because nothing drawn on the bowl took it, the bezel lying loose over a plain flange. The thread is cut in both, the bowl's on a rim turned from its flange round the movement ring's flange, with a notch for the ring's pin; which puts the bowl's bottom 49 from the ring's seat, as 05 06_01 gives it, where it had been 53 with an estimated raised seat for the cork. The transcription (
05-01-51-00-case-box-overview.md: "no thread, holes or glass groove drawn" on R-05 01 01-2) is right for the casting's sheet and left as written. - Readings settled in the audit of 3.00.00 (16 October 2026), the figures first, then the photographs, then what a maker would do:
- 05 04_1's "25,68 von Unruhmitte" and "23,8 v. Gangradmitte" put the 1941 block's screw 1.22 from hole 13, the block turned 3.4° about the stone (both points 20.2 from it: the layout's 18.8 along the detent and 7.6 across give 20.28). The layout (3.2.40) comes before the top plate's table; the 1941 block screws into the same plate as the 1943 one, at the table's hole 13 (Wempe 3955 carries the 1941 block on it), so the block stays on 13 in both states.
- 05 04 02's 14.03 −0.06 runs from the hub's flange to the lower centre's apex on the Ø 1.1 stock, the pivots not drawn: a finished staff that long would put its pivot 0.23 past the lower cock's underside (the lug's far face 10 from the top plate, the endstone 0.95 inside it), so it is the blank's, as built.
- The dashed "7ʳ" arc about hole 26 on the top plate's plan (05 08_1b) is the escape wheel's tip circle (Ø 14) drawn under the plate, not an edge of the balance opening's tongue.
- The upper cock's table gives hole 23 "Körner 4,4, kalibr. 4,59" and its Schnitt A-B the seat 5.2 H7 down to a floor 0.5 thick in the boss under the arm, the floor bored through at the table's 4.59 (read again 17 October 2026 on U30's stack and the coloured section: until then read as a seat through, opening into a sink Ø 6 × 0.5 underneath); the top plate's table gives hole 26 2.3 drilled and 2.5 reamed and Schnitt P-Q its jewel's seat. The tables are the coordinate jig's operations (punched, then reamed to locate), the sections the holes as finished: the sections are built.
- 05 06 04-2's Schnitt A-B and 05 07 04 (16 October 2026, the audit of 3.00.00): the flange's "0,87 +0,01" is the slot, "0,8" the first rib and "0,37" the second, summing to the "2 ±0,02" over both (the model had the slot 0.8, the ribs 0.6 and 0.14); "1,2 ±0,01" is the pitch, a land and its rib, so the lands are 0.87, the slot's width (the model had 02-1's pencilled 1.15 and lands 0.82, the chain's own width). 05 07 04's side views draw each hook one solid bar the chain's full width, from the 10 × 0.9 strip: the hooks were the middle layer's 0.26.
- The hand-setting (16 October 2026): Wempe 3955 was said to have it (
6_Wempe_3955_S.jpg); its plate is cut and drilled for it, but the holes, the window and the bush's bore are empty on both faces (3_Wempe_3955_uZ.jpg,8_Wempe_3955_Räderwerk_plus.jpg), and nothing of it is on its dial side. 05 08_3a's "Schnitt C-D (the hand-setting slot)", read as a slot 12 long with a recess Ø 14 and a step 2, is the window along its length: 12 +0.2 across its inner face, the ends Ø 14 arcs, and the circle in it the bore across the plate (1.68 from the dial face, the "2" its Ø); the "cut at right" on 05 08_3b (6.5, 6.5, 8.3 −0.1) is the same window, and its 37° the line of hole 26's screws, along which two of its figures are drawn. - The stop work, 05 06_4's Schnitt C-D and 05 06 04-2 (15 October 2026): C-D was used unmirrored, though A-B on the same sheet is seen from the fusee's small end and mirrored here; so the bar met the stop pin with its near side, where C-D draws the pin against its far side. Mirrored, with the pin on the far side. The body's "1,1+0,05 tief" (read as a second slot in the transcription) is the same slot's depth toward the bar's upper end: fine.py found the bar, at full thickness there, 0.26 into the chain on the turn below. The cover plate's screw is dimensioned on 02-2 ("6 r", "1"), not 90° from the slot. The slot was not cut and the bar's spring and its pin not drawn; all three are now. And the slot is dimensioned from the line through the chain's pin A ("4", no angle): along it; the model had the bar's turn set by the stop with full wind at the groove's end, 40° off it. Full wind is now the stop's, 0.112 turn short of the groove's end.
- The escape pinion (05 04 05-2, merge of P1b and P1d): first drawn on core.js's default depth (root r 0.97), so the seconds wheel's tips (11.85 − 10.95 = 0.90 from its centre) cut into its root; now on the sheet's tip Ø 2.97 and root Ø 1.6 with the train's tooth forms (WTRAIN.teeth), and phased against the seconds wheel by gearLash (movement.js).
- 05 08_1b: the "2,65" by the fusee's M1.4 holes is 22,65, hole 1 to hole 10 (its leader runs to hole 1); the dashed circle round hole 10 is J-K's recess Ø 22 × 0.7 in the inner face (not a 19 mm clearance); Schnitt J-K runs through hole 10, not the plate's edge.
- 05 08_1b: Schnitt N-O is not a lip at the barrel cut: it runs from the balance opening to hole 51 along the balance holding work's pocket, and its "1,35 −0,05" is the pocket's depth. The radius round 51 reads "4ʳ" (r 4: the "7" is its arrowhead), as it scales (4.0) and Wempe 3955's pocket measures (4.0-4.2).
- 05 08_11: the pillar's body is Ø 8.1 −0.2 (the ∅ written high, as on its 4,3∅ and 4,5∅; 8.06 scaled), not 8.14 (P0's).
- 05 08_7: the "104 +0,1" is the dial's recess in the flange's face, 0.7 +0.1 deep, not the ring's seat (85 H9); "4,7" is the flange's height; the plan's 20° is the first screw hole's angle from 12, 6° the dial's pin hole's.
- 05 08_7 (15 October 2026): the plan's "1,6" is across the radial hole at 12 o'clock (a dashed pair across the ring), the section's "1,1 Ø" across the dial's pin hole (its dashed pair 4.7 off the axis, as 50.5 sin 6°): read until then the other way round, with the radial pin at 6 o'clock. The radial pin is moved and made Ø 1.6; the dial's pin hole and the dial's pin made Ø 1.1 with it.
- 05 08_8 (15 October 2026): the "8 Ø r6 +0,028/+0,019" (read "T6" until 28 October 2026: a lower-case r whose stem the centre line crosses; ISO 286's r6 for 6-10 mm, and there is no shaft fit T6: drawing check 2's 8-M4) is the tapered part above the flange (its dimension line runs across it, under the "Kegel 1:70" leader), the "8 Ø g6" the spigot below the flange (its extension lines run down the spigot's walls): the spigot slides into the plate's 8.0 +0.015 and the bush is held by its three screws; the dust bush's 8 H7 is pressed on the r6 taper. Read until then the other way round (the spigot pressed in).
- 05 08_3b and 05 08_32-2, hole 30's seat (28 October 2026, the second drawing check's 9-M2): the Ø 5.2 H7 seat and the setting's screws are on the dial face, the 4.59 lip at the inner. Sheet b's plan shows the inner face (its pillar seats and A-B's "oben" counterbores drawn solid) and draws 30's 4.59 solid and its 5.2 dashed, and 05 08 02 dashes the setting's two screws, their heads over the setting on the seat's face (likely). Built the other way round until then. Wempe 3955's plain 2.50 is unchanged.
- 05 08_7, the ring's revised figures (28 October 2026, 9-M9): revision a (6.12.46) draws the seat 3 +0,1, the recess 0,7 +0,1, the lip to the recess 7 −0,1 and the whole 10,7 −0,1, which close only at their nominals (10,7 − 0,7 − 7 = 3; at their middles 2.95 against 3.05): built at the nominals, the plate 0.35 proud of the ring's face (0.30 at the seat's middle). The "45°" is taken as the inner cone from the lip Ø 83 to Ø 93 (possible: the section's inner slope is drawn plainly and the arrow at the far left isn't on an outside corner); the 96's tolerance is erased ("−0,3" possible).
- 05 08_11, the pillar (28 October 2026, 9-M8): the overall 25,3 −0,2 and 19,6 + 2 × 2,8 = 25,2 close only with the spigots at 2.8, so they are built 2.8 (2.75, 2,8 −0,1's middle, put the overall at 25.10, its least); its lead-in the drawn 6° over 1,1, which gives Ø 4.25 at the end, inside 4,3 −0,2 (Ø 4.3 over 1.1, 4.8°, until then); the 19,6's tolerance read ±0,04 (likely: the last glyph has a crossbar and a stem, beside the same sheet's plain "1"; ±0,01, sure, until then), which widens the endshake's ranges by 0.03 a side (Building it). The body's "8,1∅ −0,2", the ∅ written high as on "4,5∅" (or "8,14"): the model's Ø 8.0 inside both.
- 05 08_2 (05 08 01 kompl., revision a "zeichnerisch geändert", 2.11.46; the first digit a looped 2 or 8): it leaves out 26, 51, 52, 53 and the N-O pocket, their erased lines showing at 26, 52 and 53, and draws the balance opening's tongue curved, marked (a). Read as a drafting change (the owner's choice, 28 October 2026, the second drawing check's O-9, 9-M3): the same erasure took out 26, which the plate must have (the escape wheel's upper bearing is on no other sheet); the part's own sheet 05 09 01 (1943) and Wempe 3955's plate (12_, 13_) keep 51-53, the pocket and a straight tongue. "As last revised" is built so: 05 08 01's r 1 horns with 05 09 01's holes, pocket and tongue.
- The coloured section, read against the model a second time (28 October 2026, the second drawing check's batch 11): the lower balance settings' screws' label reads "WN-1" and a digit about 6 px tall, 0 or 8 (WN-10 or WN-18): undecidable on the scan, so WN-10 is kept (11-M1: the argument that one WN number can't name an M1 and an M1.2 rests on threads the model estimated); the dial's pin carries the label "Stellstift WN-201" with the ring's pin (named so since: 11-M7); the "Schrb. WN-16" leader goes to the 1941 block's banking screw, already WN-16, so the 1943 and 6MX screws stay "not read" (11-M7); the section draws the band and its hooks with the chain pin, the model keeps the chain as its default and the band under Variants (the owner's choice: 11-M8, O-10). Its heights against the model's, past ±0.3 where each part's own sheet decides and the model keeps the sheet (11-M3, 11-M15, 11-M16, 11-M18): the arbors' domed ends, the drum's floor, the escape wheel, the detent block's depth and the up-and-down pinion (11-M3); the maintaining stack (the ratchet, spring, pin, the fusee wheel's rim and WN-21), drawn 0.45-0.7 nearer the top plate than built, where the fusee arbor's 19.7 between shoulders, the Vorreiber's 3.1 −0.2 with its face re-turned at assembly and the wheel's 1.3 −0.1 recess (05 06 04-1, 05 06 00-2, 05 06 00-3) place it; the cork ring, its top drawn 0.56 nearer the bowl's bottom, which 05 06_01's "49 von Werkring-auflage" places, the cork squeezed against it; the stud's bar 0.45 higher (the stud's own 1,6 −0,2), WN-11, the hour wheel's pipe end (05 02 03's 8.2 overall) and the up-and-down stud and pipe ends 1.0 longer (05 08 02's 12,3 stud). The hands, 1.2 and 0.75 higher than the section on 3.48.00, are within 0.2 of it since batch 7 lowered them (11-M14: the hour blade 13.35-14.05 against 13.2-13.85, the minute 15.66-16.36 against 15.8-16.4). The lower escape stones are the section's, 0.8 and 0.75 thick, since no sheet sizes them (11-M17); the ring's pin WN-201 the section draws 7.1 long, but the ring's own 45° cone leaves it room only to 5.8 (11-M6, kept at 5.25); the change wheel's stud drawn into the dial, which its sheet doesn't hole (11-M19: pictorial).
- 05 08_13 (15 October 2026): the "5" is hole 48's distance from the short edge (its extension lines run parallel to the short edge) and the "7,7" hole 42's distance from the chord (its extension lines run parallel to the chord); read until then as the corner's offset from the chord and the distance along the chord to pin 41.
- 05 08_4, the lower cock's revision (a) (28 October 2026, the second drawing check's 8-M5): its "(a) Toleranz war +0,05" (2.12.46) stands directly over the "+0,1" of the setting screws' "3,5", not over the lip's 0,5 +0,03 beside it: the revision most likely widened that figure from +0,05 (05 08 03-1, not revised, and the top plate's P-Q still draw the same holes 3,5 +0,05; likely). The card "as first drawn" said the setting's seat until then. The holes are drawn at the widened figure's middle, 3.55.
- 05 08_9, the dust bush's "(7,62)" (28 October 2026, 8-M6): the bore at the mouth's foot, 1.8 under the top, a reference figure that doesn't follow from the sheet's own 8 H7 at 1:70 over the 16.3 below it (7.767-7.782; 7.62 would need 1:43, or 26.6 of taper at 1:70): the model follows the 1:70 and the fit, 7.775 (sure about the model; the sheet's 7,62 possible, a slip or another issue's taper).
- 05 08_14, the click's 17,4 (28 October 2026, 8-M10): the outline's own figures (the 9,7 to the beak's tip, the r 6 about 5,142 / 7,212, the base 2.85 under the hole by the Ø 5,7, the nose r 1 at 7,5 from the hole) close on 17.53 from the beak's foot, or 17.22 from its top corner, never on 17,4 (the sheet draws 17.44: its nose's centre 7.4 from the hole). Built on the figures, 17.53 (possible: either 7,5 runs to another point or the figures don't close); the nose isn't the working end.
- 05 08_6 (U30), the stud's screw hole (28 October 2026, 8-M1, 8-M3, O-8): U30's "5" runs from the hole's centre to the slot's far wall (its arrowhead at 61 px/mm), so 4.1 along from 23 (sure), and its "4,2" from 23's line across (sure); the hole is drawn Ø 1.43 with a dashed Ø 1.03 inside, an M1.4. The transcription read it "slot to steady hole" and "steady hole to axis". Built at 4.1 / 4.2 (the owner's choice); 4.35 until then, derived from a stud drawn symmetric, which 05 03_9 doesn't draw: its plan draws the square end 1.20 / 1.26 and the upright's hidden sides 0.96 / 0.82 about the hole's line (17.1 px/mm), built so (the upright's inner side 0.79, so it clears the slot's 3,4 end by 0.01).
- 05 08_1b (15 October 2026): the pocket N-O's dashed edges converge toward 51: the common tangents of the opening's r 5 and 51's r 4, not a constant 8.
- 05 08_10 (15 October 2026): the section draws no counterbores at 38 and 35: a 45° mouth down to the bush at 38, and the setting at 35 filling the bridge's hole.
- 05 01_3 (15 October 2026): the closing plate's Ø 1.2 is drawn with its drill point inside the boss (blind), and the rim's underside meets the boss in a round.
- 05 08_14: the click's back is an arc r 12.5, as figured (fitted 12.4-12.5); the "85" by it isn't its radius.
- P0's
dims.jssaid the Unterplatte's plan is drawn from the dial side with O to the left: it is drawn from its inner face with O to the right, as every plan of the group. - 05 08_10 (Zwischenbrücke kompl., P1b): the WN-300 leader goes to the bush at 38 (the intermediate arbor's, its face 0.7 +0.02 in); the bearing at 35 is a jewel in a setting, its face 1.7 in (05 05 04-1, -2 in the coloured section). The transcription and P1a's comments had them the other way round (a jewel at 38, a WN-300 setting at 35).
- 05 08_32.2 (P1b): WN-302 is the bush at hole 1 in Schnitt A-B (the centre arbor's; the coloured section's Messinglager WN-302 there), its "0,1 +0,02" its set-down under the plate's inner face, its sink on the dial side; the transcription put it at hole 30. The long stud's 12.3 runs from its end to the plate's inner face (it is the stud's length); the short stud's 6.8 to the dial face. The short stud is at hole 19 (S 6.3: Schnitt A-B is a projection).
- 05 05_2, _5, _8 (P1b): the "6∅", "7∅" and "10∅" beside the wheels, which the transcription read as riveting collars, are the hubs, and the "0,2" each hub's standing proud of the rim; the block under the centre wheel on 05 05_8 is its pinion.
- 05 05_10 (P1b): the sheet is of 7.6.40 (checked 20.4.43), not revised in 1946 as the drawing list gives it; the journal "C" is e8 on 05 05_8 (05 05_10's letters unreadable, read "r6?" in the transcription). Both sheets write "Kegel 1:30" along the journal: a taper, built straight until 15 October 2026; the riveting collar is drawn flared over a groove in the seat, not a plain Ø 3.0 (built so until then).
- 05 04_1's elevation: the figure between the top plate and the escape wheel's teeth reads "0,5" (the transcription's "0,9"); with "1,4" it gives the wheel's teeth 1.4 thick, standing 0.6 over the web, 0.5 under the plate.
- 05 04 02: its 6.1 runs up from the hub's flange top, not from the staff's top end, and 14.03 down from it: the transcription's overall 20.13 (6.1 + 14.03) is not the staff's length (the blank scales about 28 long; the finished staff is 25.86 between its pivots here). Its 1.1 is the arm's seat's length over the flange, 1.8 the flange, 4.1 the hub's length, 5.6 the collar's bottom.
- 05 04_1's pointed piece standing on the pipe, 7.6 long with a 12° point, dashed where it passes under the block's arm: it is a pin through the earlier block's arm at the stone (Wempe 3955's block has a brass cone there,
11_Wempe_3955_Gangfeder_plus.jpg), not part of the detent. - 05 04 01-4: the "1,4 +0,1" is the upright's left edge in from the base's end; the base is 7.5 high at its end (25 − 17.5) and its top 15-15.4 from the upright's end beside the fillet.
- 05 03_2 and the coloured section: the timing screw is 05 03 01-2 and its weight -3 (the transcription has them the other way round).
- 05 03_1 (phase 2c): the lever chronometer's balance scales 33.4 across its rim against its masses' boxed Ø 6.35 (12 px/mm), cut at 3 and 9 with the masses 30° from the cuts' line: this balance, not the transcription's 28.7 mm one. Its "unterer" and "oberer Ansteckungspunkt" lead to 15° and 20°: the two pins nearly in line in plan.
- 05 03_7 (phase 2c): the two small circles inside the curve (0.25, −0.15 and −1.31, +0.16 mm from the coil's centre) are the compass's points for its two arcs (0-90°, r 5.94; 110-220°, r 4.35), not an origin for the radii, which are from the coil's centre.
- 05 03_2 (15 October 2026): the side view's two outlines of the masses aren't two heights. The upper half is a view, its near pair whole from the rim's lower face to 6.40; the lower half is a section through the arm, whose cut (1.15, hatched) hides the far pair's foot, so their outline starts 1.24 up. P1d built that outline (5.4 from 1.1).
- 05 06_20 (15 October 2026): "Zugfeder 15 × 0,37" is not overwritten; the 7 is the sheet's stencil 7 (with a bar across and a tick at the top left), as in its "12,17" and "9,71". The transcription's "the 7 slightly overwritten" is left as written.
- 05 04_1's pointed piece on the pipe and Wempe 3955's brass cone (15 October 2026): the tail of the earlier block's banking screw, whose domed head lies beside the stone on the detent's other side (
10_Vergleich_CWW-6MX_Gangfeder_mit_Kloben.jpg), not a pin. 05 04 01-4's M1.2 across its slit upright is the 1943 block's banking screw. - 05 03_5: "bottom coil to collet bottom 0,75" matches the collet's hole 0.75 from its face (05 03 02-2): the spring's inner end lies 0.75 over the collet's underside.
- 05 06_2.2, 05 06_15, 05 08_3a, 05 08_8 (P1c): the fusee arbor's pivot (Ø 2.8 ±0.02 to 2.7) and journal (4.5 ±0.02 to 4.39) can't run in the pillar plate's hole 10 (2.70 ±0.009) or the fusee bush's bore (4.1 +0.2): both are drawn opened to the arbor and 0.02, as reamed to it at assembly (frame.js; the coloured section draws the journal Ø 4.4 in the bush). The bush's body below its flange is drawn 2.6, not 2.7: at 2.7 it stood 0.05 proud of the J-K recess's floor, 19.65 from the pillar plate, under the arbor's 19.7 +0.05.
- 05 08_1b's J-K recess: Ø 22 at the face, its 45° wall to the floor Ø 20.6 (27 October 2026, as P1a read it: 05 08_1a's section drops the 22's extension line from the wall's corner on the face line). P1c read the 22 at the floor, for the fusee's cover plate, Ø 21.1, which stands only 0.275 into the 0.7 recess, where the wall is Ø 21.45.
- 05 06 00-3 (P1c): the bore's "4 +0,1" (scaled 4.0) can't pass the arbor's seat (4.38-4.5), and the tube's figure reads "6,6 +0,1" written over a struck one, the tube drawn 6.31-6.44 (the second drawing check, 5-M10); the 1941 assembly's 6.5 H7/g6 for the ratchet on the wheel is taken (the ratchet's 6,5 H7: 05 06 02-1, 1940, unchanged 1948), and its 4.45 H7/g6 for the wheel on the arbor read as a straight seat's fit, the bore drawn 4.55 on the 1:70 seat (Estimated).
- 05 07 00-3 (P1c; 15 October 2026): the "12,5" is a diameter, its line running across the circle through its centre (scaled 12.7), and that centre lies on the "6,4" circle (scaled 3.24 from the axis): each tooth's back is an arc r 6.25 centred about 3.2 from the axis, not r 12.5; the faces lie along lines 1.2 off the radius (10°), as built before. The transcription's "tooth back arc radius 12.5" is left as written.
- Fusee and maintaining work (15 October 2026, a survey against the sheets; each built so): 05 06_16's click wheel's faces are undercut, each tip overhanging its gap ahead of its root (the 8° line from a root runs inward past the tooth's own side of the centre), not leaning back. 05 06_12's maintaining ratchet is 1.3 −0.1 thick inside its cup and 1.02 at its teeth (the section draws the floor inside the cup higher), so "2,1" is the cup's rim over the plate outside it; revision (a)'s 0.3 +0.15 × 45° is on the cup's outer top edge. 05 06_14's click: the nose's face at 85° leans back toward the pivot; the base line is the r 3 hollow's chord, 1.52 under the hole, ending at the nose's foot 5.2 from it. 05 05_12's maintaining detent: its tip's end is straight, 2.6 over the line tangent to the boss's underside, at 80° to it, leaning back toward the hole, its lower corner on r 12 (not an arc on r 12). 05 06_7's fusee wheel: its underside recess's mouth is chamfered 60° from Ø 17 +0.2 (the angle from the axis: from the face it would run deeper than the recess). 05 06_8's cover plate: "0,4 −0,1" is the bore's straight land under the hole's 60° chamfer, which opens to the outer face, not a recess in the face on the body; its screw lies 11° from the stop bar's length toward its stop-pin end (05 06_4 C-D: the hole drawn 1.15 across, 5.87 along), on the side away from the bar; Wempe 3955's (8_…Räderwerk_plus.jpg) agrees within perspective (about 19°). 05 06_6's Vorreiber: the 0.3 × 45° is on the flange's hub-side face; face a carries only the Ø 9.9 recess. 05 07_8's hook: the pin's end is a ramp, flush to 0.5 at a radial face (15°), not a flat 0.5 proud. 05 07_14's chain hooks: the top hook is 5 to its crown and 3.5 wide with its nose turned back toward the chain (the model's 3.95 × 2.8 contradicted its own figures); the bottom hook's barb root is 3.5 from its last rivet and its tip points back toward the rivet, 1.4 past the shank, into the drum (it hooked forward, outward). 05 06_10's maintaining spring widens from 272° to 3.65 at its hole (295°) and 4 at its end, traced (3.4 at 288° estimated before).
- The transcription's maintaining spring angles (P1c): 05 06 01-1's 65° is measured from 0° the other way round from the widths' table (its square end lies at the lower left): its pin at 295° on the table's sense.
- The maintaining spring's pins (16 October 2026): the model pinned its eye to the fusee wheel and its other end to the ratchet, the ratchet's sheet turned 65° to meet it. 05 06_4's Schnitt A-B draws the eye's pin whole and labels it "Stift nach oben" (up: into the ratchet, which lies above the spring), the pin at 65° hidden (under the ratchet's plate: down, into the wheel), and the eye at 6 o'clock between the clicks at 9 and 3, where the ratchet's own sheet (05 06 02-1) puts its pin hole: the eye's pin is the ratchet's (sure). So the drive closes the ring onto its banking rather than opening it against the recess's wall (Physics: energy, The maintaining spring).
- The maintaining spring's eye's hole (16 October 2026): on its 0° line, as 05 06 01-1 draws it to scale, not 0.8 off it toward the square end (the transcription's reading of the sheet's "0,8": Unresolved); the ratchet's pin hole, at 6 o'clock on its own sheet, then lies under it with no turn of the ratchet's sheet.
- The maintaining spring's eye (16 October 2026): 05 06 01-1 gives "0,8" by its eye's hole, which the model took (P1c) as the hole's offset from the 0° line toward the square end; but the sheet, to scale there (the eye's r 1.8 scales 1.83), draws the hole on that line (0.06 off, measured on the scan), and the 0.8's leaders run to a line about 2 mm off it, so the hole is built on the line (fusee.js
EYO). On it the running drive leaves the ring's ends 0.27-0.58 mm apart (Gould's "ends nearly meeting"); with the hole 0.8 toward the square end they would meet at 13.5° and the ring run closed onto them; 0.8 the other way, 1.1-1.4 mm apart (wempe_sustaining.js reports each). What the 0.8 measures isn't known. Its working, 11-14 minutes with the key held, is about the same in each. - 05 06_9's handwritten "x = 0,27 mm" (020605): not the spring's deflection under the drive (its section gives 14-16°, 3.3-3.7 mm at its pins); perhaps a set or a gap to be kept; its other notes ("angespannt ... bis 4,5") are illegible.
- 05 05 05 (P1c): the detent's thin tip is flush with the face away from its lower shoulder (the kompl. sheet draws it so), not the lower face as transcribed from 05 05 05-1's section, which is drawn the other way up.
- 05 05_8 (P1e): the block on the cannon tube's foot is its pinion (14 leaves, Ø 5.86 at 5:1), 2.4 high (25.4 − 23), not a collar; the tube is steel (blue in the coloured section); its 14.3, 10.8 and 6.3 run from the C shoulder.
- 05 02_6 (P1e): the change pinion is 2.6 long (2.5 on 05 02_1) and Ø 7.3 across at 5:1 (67.4 px/mm by the 4.3 and 7), not the transcription's 2.0 and 5.2; the 4.3 +0.1 runs from the pipe's top to the pinion's lower face, with an undimensioned collar 0.6 over the wheel.
- 05 02_8 (P1e): the hour wheel's collar is Ø 7.9 (plan and section, 17.1 px/mm) and its bore 3.5, not the transcription's 6.1 and 3.2.
- 05 02_10 (P1e): the 5.2 runs from the wheel's lower face to the pipe's foot and the 2.8 from its upper face to the top.
- 05 02_1 (15 October 2026): its "1,2" over the hands is the minute hand's own (its top to its flange's underside, as 05 02 00-1 gives it), not the gap to the hour hand, which scales 0.49 (5.8 px at 11.87 px/mm); the model had the minute hand 1.2 over the hour hand until then. The studs scale Ø 1.52 there, both ends domed.
- 05 02_3 (15 October 2026): the hour hand's blade lies with its underside flush with the flange's, its top 0.3 under the flange's top (the side view), not flush with the top as built until then.
- 05 02_1 (P1e): the struck "15,8" (pencil "17,0") runs from the plate's dial face to the glass's underside, and the "3,5" (pencil "8,5" or "4,5") from the minute hand to the glass; the hour wheel there runs 4.0 from its lower face to its collar's top, 0.3 under the dial.
- 05 36 (P1e): the plan is the top plate's inner face seen from below, S up (a reflected similarity puts it on holes 23, 51 and 52 to 0.08 mm); part 27 (127-556.06 U 02) is the lever drawn dashed from the tongs to its pivot at 52, not the tongs; the dotted ring round the staff in Schnitt A-B is Ø 5.85, the closed tongs' opening; Schnitt A-B's cross-hatched ring under the collar's flange is the patent's brake ring of Preßstoff (18 October 2026), not the collar.
- 05 02_12 (P1e): the hole at 4 o'clock is Ø 1.1 under a sink Ø 1.8 H7 1.0 deep.
- 05 01 01 and R-05 01 01-2 (P1f): the transcription's 4.78 px/mm for Glasrand kompl. is right, but its ring then measures Ø 121 and 13.2 high: the 1941 finished bezel, not the 1942 casting's 125 and 16; the zigzag dashed in its lower bore at the left (a thread?) is not read.
- 05 01_7 (P1f): the key's handle is a flat round paddle Ø 34.5, 3 thick in the body's slot (the section draws it as a bar), not a ball; its "set into the body 6.7" is the paddle's edge in the slot.
- 05 01_8 (P1f): the "35 ∅" is an arc in the side view, not a spherical seat in the body's top face; what its "6,3 +0,1" measures (the slot's depth, scaled 6.6-7.2, or the cross hole's place) isn't settled.
- 51 00_2 (P1f): the 105 runs from the bottom to the line across the side, and the M6 is 11.5 under that line (93.5 over the bottom), not 105 over it.
- 05 01_1 (P1f): the ring's circles fitted on Schnitt A-B give Ø 139.2 and 146.8 to the lines' edges, so about Ø 140 inside and 146.6 outside (the transcription's 138 and 145.4).
- 05 04_23 (15 October 2026, the escape wheel's tooth, its lines traced and circles fitted at 82.8 px/mm, rms 0.25 px): the "11,7" is the gaps' floor, which the locking face runs straight down to, not a recess's edge; the "12,1" is the top of a 0.2 step at the back's foot, 15° (the sheet's "15°") behind the tip, not the root; the face leans 25° from the radius through the tip (the sheet's "25°", fitted 25.2), not 15°. The crossing's flanks are each one arc r 7.9 (fitted 7.93, 7.92) centred 9.43 out on the openings' middle lines: an opening is bounded by one such arc, not two meeting at a point.
- 05 04_7.2 (15 October 2026): the "2" at the top-plate end runs to the arbor's shoulder, 0.4 under the wheel; the wheel is placed by the "19" from the pinion end, its face 2.38 from the top-plate end. Its collet 05 04 10 is two steps, Ø 2.8 for 1.6 and Ø 1.7 on to 4.7, not a cone.
- 05 03_4 (15 October 2026): the "6,5" is the arm's width at the hub, where its two hollow arcs r 20 meet in a point (the arcs' centres outside the arm, the sheet marking one); it is 4 wide where they leave its straight flanks, about 6.1 from the centre.
- 05 03_8 (15 October 2026): the collet's ends are arcs about the bore, and the bore lies in the middle of its length; its slit stops 0.1 short of the bore.
- 02 04 02 (15 October 2026): the impulse stone's end is bevelled 45°, its back 1.3 long against the face's 1.8.
- 05 04 01-4 (15 October 2026): the view under the front view draws the base 6.5 deep only for 6.4 from its end and 3 deep beyond. The sheet reads as first-angle projection throughout (its side view shows the M1 hole in the end face as seen, its lower view the upright as seen from above, and only so does the Ø 1.3, 3 deep from the front face, meet the M1 2.3 from it): Unresolved.
- 05 08 05-2 (16 October 2026): the click's "85" is its beak's end face at 85° to the base, and the "5,7" the thin circle about the hole, tangent to the base, which so lies 2.85 under the hole (scaled 2.81): Closed.
- 05 05 03-2 (16 October 2026): the "1,6 −0,1" is the centre wheel's seat alone, not seat and riveting collar together: Closed.
- 05 05 05-1 (16 October 2026): the maintaining detent's step is a straight hidden edge from the back at 8.6 to the hollow, not an arc at 8.6 about the hole: Closed.
- 05 07 02 (16 October 2026): the barrel arbor's end view is seen from the square's end (first-angle), and so read the hook holds the spring with the arbor pulled as the crossed chain pulls it, its face on the other side from where it was built: Closed.
- 05 04_1 (16 October 2026): its "24°" is the escape wheel's pitch and its 1°, 21° and 2° the wheel's angles, not the balance's; the impulse face is drawn 28°10' before the line of centres (6° + 22°10'), where the model had it 24°: Closed.
- Wempe 3955's seconds numerals are radial, as the sheet draws them, not upright (16 October 2026): Closed.
- The coloured section read again against the model, cut through each pair of arbors at its scale (17 October 2026; the transcription corrected beside it):
- The balance's hub screws (WN-10) go in from the arm's top, their countersunk heads flush in it, through the arm into the flange's M1 (px 1467-1524 × 314-341); built until then from under the flange, as the section was misread.
- The dust plate's recess is in its face toward the key (the section; the sheet's 1:100 hole narrows toward it): built until then on the face toward the plates.
- "Schrb. WN-16" is the banking screw's label (its leader to the slotted head on the 1941 block's arm); the balance's lower setting screws have their own, "Schraube WN-10" (px 1503-1525 × 488-506, missing from the transcription), which the model had given WN-16.
- "Stellstift WN-205" is the detent foot's steady pins (the Ø 0.53 circles in the foot), "Stellstift 2 WN-201" the block's pins (the dashed Ø 1.0 under the foot, up through the top plate): the model had them the other way round.
- #88's "WN-58 (or 38)" reads WN-52, the intermediate bridge's screw (built so); #20's "Stift 05 06 04-4" is the stop bar spring's pin in the fusee's body (05 06 04's parts list, piece 5, a 0.5 pin), not a small-end piece.
- The coloured section's open readings settled (18 October 2026), each against the dimensioned sheets and photographs:
- The 1941 banking (WN-16) is a whole screw: its gilt domed head Ø 3.3 on the wheel's side of the pipe, which banks on it, and its pointed tail past the arm (05 04_1's plan, the section, Wempe 3955's 11_ and 10_ photographs): until then only the tail was built and the head taken for a dish on no sheet.
- The upper cock has a boss round its setting, its face 3.2 from the top (05 08 03-1's "3,2 ±0,02"), the seat 2.7 deep to a floor bored 4.59, both settings in from the top (U30, the section).
- WN-12a is the tapped hole in a mass's top (05 03_2's plan's double circle, the section's screw on one mass), not a nut; WN-12 threads through the outer jaw to the rim.
- The stop bar's pin 05 06 03-2 is pressed across the bar, its spring bearing on it (05 06_4's C-D); the gold spring's screw head Ø 1.4 (photographs); WN-34 3.2 long (the section).
- Read and found right as built: the hairspring collet (05 03_8: the section's is pictorial), the band's hook near the lid (the band's place fully wound), the 2.3 high steel at the maintaining spring's eye (its pin), the dashed "slot" in the drum's wall (the barrel bridge screw's end).
- 05 06 04-2's Schnitt C-D and 51 00 10 (25 October 2026, the per-part audit's batch 3): the body's three M2 holes stood 47° from where C-D draws them (an estimate, PHI0 + 0.3, never read off the view: cut so, the nearest would have broken into the cover plate's M1.7 6 deep beside it); and the handle's oval 70 × 30 was built as an aluminium pressing hung from the strap, where the section draws it as an unhatched hollow 10.5 deep in the hatched side wall, a finger recess behind the strap (both rebuilt).
- 05 01's three disagreements in the gimbals (25 October 2026; each read on the scan's pixel profiles, line centres, 2.45 px/mm, ±0.4 a reading; Unresolved until then):
- The case brackets' boss: 9.0 wide (likely; 12.4 from Schnitt A-B until then). The elevation draws the 6 o'clock bracket face on (the pivots a left and right, the locking bracket at 50° standing where 46.7 off the axis puts it): its edge at 288.2-289.0 px from 4.7 over the pivots to 20.1 under, the boss and the crank one width, the axis 277.1-277.5 px by the bowl's two sides at that height (148.4-149.0, 405.8-406.0; the dash-dot C line leans 1.4 px over 105 px, which put it about 1 px right and gave 8.0 before): 10.8-11.4 px, 9.0 ±0.5. Schnitt A-B draws the boss 12.0 (its sides 260.4/289.7 px at 12 o'clock, 257.3/286.7 at 6; not 12.6) and the crank under it 12.1. A face-on outline can't be narrower than a level section, so no crank, chamfer or boss on a wider foot reconciles them: one view is drawn wrong. Kirow DEC 422's bracket face on (
11_Kirow_DEC_422_Gehäuse.jpg: block 100 px, screws 332.5 px apart, heads 82.5) has the elevation's proportions (the block 0.30 of the screws' spacing and the head 0.83 of the block; the elevation 0.29 and 0.81, A-B 0.38 and 0.58), and Kirov 247's block is 8.7: the elevation's taken. The foot's screws 15.0 either side kept: the elevation's head, a circle fitted to it, 38.1 px off the axis at its face (r about 60), A-B's slots 37.6-37.9 px at r 58.5, both 15.0 at the foot's face (r 57.7) where the screws stand radially. - The "11,5": it is the box's, from the pivots to its parting line, not the ring's (sure). Its upper extension line (y 114.9 px) is the box wall's top in the elevation's section (115.1 px; 116.3 on the right), 0.9 under the ring's top (112.7); 51 00 10 puts the same M6 11.5 under the line 105 over the box's bottom. The ring is drawn centred on its pivots in both views (the elevation's top, axis and bottom 112.7, 142.0, 171.0 px at 9 o'clock and 113.9, 143.9, 173.0 at 3: 12.0/11.8 and 12.2/11.9): built ±12.0, its top 0.5 over the parting line (05 01 draws it about 1 over) and 6.7 over the bowl's (11.5 over the pivots and 12.5 under until then); the 6MX's lock lever, laid over the ring, rises with it (its underside 0.5 over the ring's top, estimated).
- The outer pivots (WN-80): 05 01's form kept (likely). Its elevation and Schnitt A-B agree: the M6 (13.2-13.8 px, 5.4-5.6; A-B 6.1) from the wall through the lock nut at a (WN-400, the parts list's 10: a bearing disc with no number until 28 October 2026, 10-M12) to the ring's outside, a tip Ø 3.25 (8 px; A-B 3.3) through the ring to its inside. 51 00 10 (2.40 px/mm) draws the M6 (6.2 in the panel) standing 4.1 past the wall's inside at 6.8, then a pin Ø 2.7 × 6.0, the head Ø 12.4 × 4.3: its pin reaches the ring's inside too (the 2.0 left past the disc and the ring's 4.0), so the two differ only in where the M6 stops and by the pin's 0.3-0.5. 51 00 10 is the handle's sheet, the screw only context (its M6 and the 4.8 drill dimensioned); 05 01 names the screw, draws it alike in two views and was reissued in 1946 and 1947; and 2 stood off either side would let the ring slide 4 between its pivots, against its "Lagerstellen a u. b leicht spielend". What would settle it: WN-80's own sheet or the ring's (05 01 00-5), not in the set.
- The case brackets' boss: 9.0 wide (likely; 12.4 from Schnitt A-B until then). The elevation draws the 6 o'clock bracket face on (the pivots a left and right, the locking bracket at 50° standing where 46.7 off the axis puts it): its edge at 288.2-289.0 px from 4.7 over the pivots to 20.1 under, the boss and the crank one width, the axis 277.1-277.5 px by the bowl's two sides at that height (148.4-149.0, 405.8-406.0; the dash-dot C line leans 1.4 px over 105 px, which put it about 1 px right and gave 8.0 before): 10.8-11.4 px, 9.0 ±0.5. Schnitt A-B draws the boss 12.0 (its sides 260.4/289.7 px at 12 o'clock, 257.3/286.7 at 6; not 12.6) and the crank under it 12.1. A face-on outline can't be narrower than a level section, so no crank, chamfer or boss on a wider foot reconciles them: one view is drawn wrong. Kirow DEC 422's bracket face on (
- 0207's chain slot (25 October 2026; Unresolved until then, read as 45° from 6 o'clock and 180° from the rivet hole). On its plan ("Federhausdeckel abgenommen", 12.27 px/mm by the drum's outside and bore fitted as circles, rms 0.24 px, centre (154.7, 284.9) px) the Steg's notch is on the 12 o'clock centre line (0.3°), the M2.6 hole is "45°" from it, and the "Schlitz für Kette" lies on the same line at 6 o'clock: its walls 176.5° and 184.8° from 12 at the bore, 174.3° and 181.3° at the rim, so 180° ±2 (sure). The "45°" beside it is its lean through the wall: that dimension's arc is centred on the slot's wall where it meets the rim (radii 58 and 60 px about (150, 537)), not on the drum's centre (192 and 215 px), its arms the 6 o'clock line and the wall produced. The section, cut along that line, draws the Steg (106) under the wall at the top and the slot through the wall at the bottom, 10.4 px (0.87: the "0,85") along the axis, its middle 4.66 from the bottom's outer face. So the slot stands 180° from the Steg and 135° from the rivet hole; the hole 45° from the Steg on the side the strip's end needs (the strip comes back to the block from the Steg, the drum running rotation.y falling; 05 07 01-1 the same), so the slot is the hole + 135° (rotation.y rising). The slot is the chain's (cut at the fusee's assembly where the laid chain's barb comes, -19.57°, the drum standing at 0 fully wound), so the drum's insides were turned to it: the rivet hole at BLK 3.585 (the slot + 5π/4; 1.2, an estimate, until then, the slot 88° from it), the hook block, the Steg and the bottom's and lid's notches for it, the 1941 drum's slots, the mainspring and the arbor's hook, all together (+136.6°). Nothing re-solved: the solve holds the strip's end and the Steg relative to each other (tools/wempe_mainspring.py's BLOCK, STEG; mainspring.py's bounds() reckons from the strip's end), and the page draws the spring from the arbor's hook (HKA), which follows BLK; fusee.js logs an error if the slot moves off BLK − 225°. The slot is cut at that lean (25 October 2026; radial until then): 45° to the radius, leaning back toward the chain's run going in as the bottom hook's barb does (its 50° flank), its walls 2.5 apart round the drum at the rim (1.77 across), 0.85 along the axis, its middle line through the wall's middle at the barb's angle, in both drums for both connectors (fusee.js, DRUM); 0207's walls are drawn freehand (48° and about 30° on the plan), the dimension decides. 0207 is the drum of 1941; the later sheets don't draw the slot (likely for them: the lid's 3 o'clock notch of 05 07 01-2, opposite the Steg, then stands at its angle). The band's slot (no sheet) stands 162° from the Steg.
- 05 06_4's Schnitt C-D, the stop work's figures (27 October 2026; Unresolved since the drawings check, which read "2" from the stop pin's R 14 and "12" and "17,6" as radii, so the bar's ends on r 12 against the 22,5 bar). On the sheet at 7-12× (the scan 12.2 px/mm by the 22,5): the "2" runs from the thick circle, the hub Ø 21, out to a thin arc through the bar's upper far corner, so that corner stands on r 12.5 (the model's 12.51); the "12" is "1,2", from the hub's circle in to a thin arc at r 9.3, the top land's floor, where the bar's lower end lies at full wind (the model's 9.32 there); the "176" is "1,76", from the hub out to the thin arc through the lower point running, r 12.26 (the model's 12.36, set by the 22,5 and the "2" together: the sheet's own 0.1). The "3,2" is the lower end's way between C-D's two positions, running and "im aufgezogenen Zustand": drawn 3.6 (the model's limit, where the spring's wound shape is traced). The slide the chain gives at full wind is 3.36 (
wempe_stopwork.py), 3.26 with the lower point at the 1,76: 0.16 over the figure, which the model's own chain path can't vouch for (until 28 October 2026 this said the figures agreed to the sheet's 0.1; the second drawing check, 3-M15, found that circular: the drawn positions are 0.35-0.45 off the figure, so the figure rules). The model keeps the drawn bar (sure of the readings: the arrows end on the hub's line); the overshoot and why it stays are in Estimated. - 05 06 01-1's maintaining spring near its eye and in its swell (27 October 2026; Unresolved since the drawings check: the eye's join to the band not drawn, the swell's r 6 sampled at 4° and joined straight). Traced along rays from the ring's centre (
tools/wempe_maintspring.py, 17.26 px/mm by the ring's two circles, rms 0.016 and 0.035): the band is not 2 wide up to the eye but widens toward it, its inner edge an arc r 10.40 (rms 0.005 over 11-40° from the eye) tangent to the ring's inner circle about 50° from the eye, meeting the eye's round in a shallow corner (0.08 into it); the swell is the "6" about the small circle drawn on the 9 o'clock line (8.125 from the axis, tangent to the inner circle at 270°; the trace within 0.02 of it over 278-293.5°); from its corner (293.9°) to the square end an arc r 13.24 (rms 0.004 over 295-335°) through the "4". The outer edge runs into the eye's round with no step on both sheets, its line coming in over the 60° before the eye (0.17 inside its own radius at 10°, 0.07 at 60°, the drawn ring wandering ±0.08); built as an arc tangent to the ring 60° from the eye and to the eye's round (estimated: the angle). The spring's stiffness is unchanged to the check's tolerance (wempe_sustaining.js: 1.2204 ψ + 0.2960 ψ² N·m, escphys.js's 1.2204 and 0.2956), its eye and square end, so its banking, as before. - 05 06 02-2's click springs have two holes (27 October 2026): the "0,6∅" across the end, between two dashed lines 18° from the figured hole (5 from the end), is a second hole Ø 0.6, on the cup's 42° pin, which 05 06 02 draws through the spring as the 60° pin is (the transcription had it "the end's width or a second hole"). Both cut, on the strip's middle (the "0,8 −0,05" from its edge at its lower limit).
- 05 06 02-1's revision (a) (27 October 2026): "Maß 25,4∅ gestr.; 0,3 +0,15 neu" replaced the chamfer's top diameter by its size, 26.1 − 2 × 0.35 = 25.4: the chamfer is the same in both issues (built so, its top Ø 25.4 on the drawn cup), and the first issue differs only in its tips, Ø 37.5 for 37.25 (the drawings check had it "no chamfer"). Built as first drawn (its tolerance not kept: the revised −0.1 taken, drawn 37.45), the maintaining detent seated on its teeth in that version.
- The barrel's open items from the drawings check (27 October 2026; Unresolved until then):
- The drum's seat 1.2 deep, the lid 1.2 (its 1,3 −0,1 at its least) and flush. 05 07 01-1's revision a (11.3.48) put the seat's "1,2 −0,1" in brackets ("Maß 1,2-0,1 in Klammern"): the chain 18,1 − 13,8 − 3,1 fixes it, and its 13,8 −0,05 from the seat's floor to the boss holds only on a 1.2 seat (13.78; 13.68 on the 1.3 seat cut since 26 October). The lid then lies on the rim at the bottom of its tolerance, as 05 07 01 draws it; the spring's space 15.63, its middle 0.015 off the hook block's (sure for the seat, likely for the lid's thickness: a 1.3 lid would stand 0.1 proud, which no view shows at 2:1).
- The 1943 arbor 40.2 over all (05 07 02's 40,2 ±0,1 with its 5 and 10): the bridge pivot 2.93 (3.38 until now, 40.65 over all), the square starting 0.42 inside the barrel bridge's hole, the set-up ratchet pressed down its 1:100 taper to 0.05 off the bridge as before (likely: the sheet scales 40.4, not to scale).
- The arbor's hook 05 07 02-2: a head on the Ø 2 pin, its radial face 15° off the pin's centre line (the end view unwrapped about the core: the face at 15.5°, the land falling evenly to flush 4-5° past the line), 0,5 −0,05 high (drawn 0.475), 2 along the axis; wider than the pin as the 1941 hook's 3-wide head (0207). The mainspring's eye bears on the face, the strip unchanged (its tip moves with the face, the hook turns 6.4° to it). Until now the pin's own end ramped across its 2 (the face its flat side, 8.6° off, 0.545 proud at its edges). The head's sheet (05 07 02-2) isn't in the set: its 20° span and the land's evenness are the end view's (likely).
- The band's hooks 05 07 03-2 and -3, from their sheets (above, The band): placeholders about half the size until now. Read on the sheets: the "7r" at each one's bottom is "1r" (the 2,5 and 1,4 / 1,0 put its centre, the throat's wall and the left wall meet it tangent, the traced arcs 1.01 ±0.002); 05 07 03-2's bracketed crown "(1,5r)" is drawn r 2.08 and its "2,8" below the back's centre is drawn 1.70 (the drawing kept for both, its "6r" and "3,55" agreeing with it); its "30°" is 31.7 between the nose and the seat its figures place; 05 07 03-3's back, tangent to its tip at the figures (r 10 about 1,2 below), lies 0.10-0.15 inside the drawn line (the figures kept).
- 05 04_1's 5°: where the tooth is let go (11 November 2026; the owner's choice). The sheet's "5°" stands on the balance's arc with its 6° and 22°10', 7.0 from the balance's centre (its arrows at 82.0°, 75.7° and 70.8° about it, the line of centres at 53.5°): it runs from where the impulse stone's corner enters the teeth's path, 22°10' before the line of centres, on toward the line, to about 17° before it. Read: the impulse stone is 5° inside the teeth's path when the tooth is let go, the rule of the period for this escapement (Watch and Clock Escapements, 1904, Fig. 141, which
keystone.jsquotes; likely). Until then the figure was listed as not identified (Unresolved) and the discharge stone's place was an estimate, 5° after rest at the gold spring's tip, the tooth let go 4.2° before the impulse stone was in its path and running free to it. Built:DSB14.2, the discharge roller turned 9.2° on the staff, which puts makeEsc's release 4.95° after the stone's corner comes in (wempe_escapement.jschecks it within 0.15°): the gold spring met 1.6° before rest, the release 11.3° after. The sheet also draws the stone itself, dashed under the impulse roller and about 10 px across, its flat end on the gold spring's tip with the balance at rest: the start of the unlocking, as the model now has it (moderately sure).- The "1°" by the gold spring's tip is likely the discharge stone against the tip as drawn, the unlocking beginning 1° before rest: the model meets it 1.6° before (not built to; likely, not settled).
- The 1958 repair book (Эксплуатация и ремонт измерителей времени, p. 60, the MX's assembly checks) has the gold spring's end at rest short of the discharge stone: «конец золотой пружины при равновесии не доходил до спускового камня на 0,10—0,15 мм». At the stone's end, r 1.60 from the staff, 0.10-0.15 mm is 3.6-5.4° of the balance. If the stone is still coming it would meet the spring that much after rest, the release 16.5-18.3° after rest and the impulse stone 10-12° inside the path (the swing at 12 h 144-138°); if it has gone by, the tooth would be let go 5-7° before rest, long before the impulse stone is in its path, with no impulse on a real escapement. Neither is the sheet's 5°, and the text doesn't say which side; a Soviet MX's adjustment of 1958 may differ from Wempe's layout of 1941. The sheet is built; the book's gap is not reconciled (Unresolved).
tools/wempe_discharge.jsprints every reading's events and swing.
The estimates
What no sheet gives is estimated, and every estimate is listed in the model's README with the reading it rests on ( in all). Grouped by the phase that built it:
| Group | Estimates |
|---|---|
| The frame (P1a) | 41 |
| From the parts audit (3 November 2026) | 3 |
| The train (P1b) | 11 |
| The fusee and barrel (P1c) | 12 |
| The escapement (P1d) | 15 |
| The energy budget (phase 2b) | 5 |
| The escapement in time (phase 2a) | 9 |
| The escapement in time (phase 2d) | 5 |
| The transmission (16 October 2026), tools/wempe_transmission.js | 8 |
| The hairspring and temperature (phase 2c) | 5 |
| The dial, motion work and hands (P1e) | 12 |
| The case and box (P1f) | 12 |
| The case, gimbals and the trial (phase 2d) | 5 |
| The Soviet 6MX (the Variants' third version, Kirov No. 247; The Soviet 6MX above). Measured on Altmeppen's photographs, each fitted on the sheets' hole table; estimated or chosen where they don't show | 17 |
| Left out, small | 1 |
| In all | 161 |
The frame (P1a): 41
- The key's paddle in brass (9 November 2026): the default key's paddle brass with its body, as The Mariner's Chronometer, Fig. 2.35's bare brass body; 51 00 11 gives the paddle no material and no photograph read for it settles its colour.
- The fusee's pins (28 October 2026, the second drawing check's batch 5): the Vorreiber's pin (05 06 00-5, no sheet) Ø 1.16 in its holes reamed together Ø 1.15, its size reconciled from the hub's 0.8, the arbor's 1.1 taper-reamed and 05 06_1's 1.2 (the arbor, above), its 1:50 taper not drawn, its 8.3 length scaled on the coloured section (±0.15); the chain's pin (05 06 00-6, no sheet) pressed Ø 0.567 in the ribs' 0.555; the fusee wheel's bore 4.55, 0.04-0.06 clear on the 1:70 seat, which neither its "4 +0,1" nor 05 06_1's straight 4,45 H7/g6 can be. The dust plate 1.0 from the square's root as 05 06_1 figures it, its hole at 3.110 there (within its H7); at the fits' middles it would sit 1.3 off, and the coloured section draws it on the root.
- The navigator's voyage (Navigating by it,
wempe_navigation.js): the route, from 45° N in port to 15° N by day 20 where the box reaches 85 °F, is estimated (no source gives one; the latitude only scales miles of longitude by its cosine, and the equator's figures are given beside it). Bowditch's probable error of a fix (±2 miles) is taken as a circular normal whose median radius is 2 miles (σ 1.70 a side); Bowditch gives the figure, not its distribution. - The detent's knock margin: since 19 October 2026's physics pass, with the estimated 0.8 g preload, a 3 ms blow across the plate of 25.6 g lets a tooth go on the frame as drawn (22.6 g at 0.8 times, 28.7 g at 1.2 times; the knock's floor under 0.64 g, below the margin's 0.78 g, which the bench takes). Before it (18 October 2026), with the estimated 0.63 g preload, a 3 ms blow across the plate of 20.4 g lets a tooth go on the frame as drawn (20.0-20.1 g before the horn was traced) (
tripping.js --model wempe, its least-knock search refined from six halvings to ten: the coarse one read 22 g). The check asks 20 g or more, so the margin is a hair at the estimate. The model keeps the estimate; the bench takes the knock's floor, 0.61 g, as a second least beside the margin's 0.51 (the user's choice), its window 0.61-1.55 g aimed near 0.84 g, where the 3 ms blow wants about 25 g (the line through the frame's runs carried on past 1.2 times: estimated). - The key holder (case.js,
Schluesselhalter,Schluesselhalter.F; 18 October 2026): the box's plan, 127-556. A-1 (51-00_1, 1:2, the Boden-Chronometer's arrangement, a lever chronometer's, borrowed for the Einheits box; scaled 1.24-1.25 px/mm by the box's 185 and the gimbal ring's Ø 146.6), draws it: a triangle in the back right corner, its legs 22.3 along the two lines it is drawn against (2-4 mm inside the box's inner faces as the box's centre places them, taken as the walls), and on its long edge a round fitting, the circle fitted on 8 rim points (0.4 px rms): Ø 19.5 ±1, its centre 10.35 from each of those lines (13.4-14.5 from the inner faces by the box's centre) and 1.1 inside the long edge, with two dots on the box's diagonal 11.9 apart (about Ø 2.4). Lange VEB 2285's box (drouot_33246921_langeVEB2285_3, from above) shows the same arrangement: a wooden corner shelf and the key's body in a round black cup standing over its front edge. Built (the user's reading, 18 October 2026): the key's axis 14 ±1 from each wall (16.5 until then, estimated, and 21 before 16 October 2026; 13.5 would leave the paddle 0.24 from the walls). The shelf's front edge (the owner, 24 October 2026) is a concave arc following the gimbal ring, as Wempe 6161's (antiquorum_208-4_wempe6161) and Wempe 3044's (milivault_529241_wempe3044_screen) boxes show it, drawn about the box's centre at r 82.5 so the Ø 19.5 cup stands wholly on the wood, 1 inside it (legs 59.8 along the walls), the key's tube through a hole r 6, 10 thick; until then the plan's straight edge 1.1 beyond the key, which left the cup half over nothing and the key's tube in an open notch. Estimated: the cup's height 5 and black finish (Lange 2285's; the drawing gives neither), its Ø 11 bore (the key's cone seats on its top edge, 65 over the floor, so the 1943 key's paddle stands 20.7 over the box's top as before: on the wartime Wempe,rmg_L5393_wempe_wartime_001, 24 ±6, 20 ±8 read apart); the screws 14 apart with heads Ø 2.2 on Ø 1.2 shanks, both into the shelf (the dots' 11.9 and Ø 2.4 would put the heads over the key's bore, so they are built as far out as the reading's ±1 allows), the shelf's thickness, its front arc's radius and centre (3044's shelf scales about 45-50 along the walls, ±15 %, against the model's 59.8); that the drawn corner lines are the walls. The paddle (Ø 34.5 × 3, facing the box's middle) clears the walls and the closed lid's by 0.74 at its widest, the 1940 key's pear by 0.57 (measured on the page). The 6MX's shelf (legs 65, its hole at the same place) stands 15-30 under the rim with the paddle above (moMvyx8eXfo 3:06, a 2022 box, empty; 12_Kirow_DEC_422_Kasten_1); Wempe 5377's, in a later case, under it. Of the box's wood. - The page's ship motion (The page's time, ship motion and reports): the sea itself (14° of roll each way, pitch 0.55 of it, the axes 5 m below the box) is the Hamilton's illustrative motion; the gimbals' damping ζ 0.05 is the Hamilton's estimate; the time the transit lock takes to level the gimbals (about a second) and the twist that restarts a balance stopped to set the hands (the Twist button's 0.6 of the running swing) are estimated. The gimbals' periods are the model's own (weighed).
- As first drawn (phases E1, E2, above): the 1941 barrel's seats (their mouths Ø 39.25 and 39.2: 020701-3's 1.5-deep seat with its 5° undercut taken as faced 0.3 to 0207's flush 1.2 when the ring goes from 19 to 18, the lid's 3° seat 1.0 deep, each disc's edge turned to its seat's cone: 28 October 2026) and its boss's cone (020701, likely); the 1941 lid's oil sink Ø 7.4 (0207 draws it undimensioned: scaled against the bottom's dimensioned Ø 8, at the bottom's 10°) and its prising notch's size and place (020701's plan, scaled 2.5 × 1.9, half-round; opposite the Steg as that plan is turned onto 0207's, both seen from the bridge's side: likely); the 1941 arbor's journals Ø 4.48 in the discs' Ø 4.55 and its pivots 2.88 and 3.88 (the 1948 drum's fit and the frame's reamed holes: 020704-1 and 0207 draw the journals Ø 5 ±0.02 and the pivots Ø 3 and Ø 4, 0207 the discs' bores Ø 5, while 020701 draws them Ø 4.5 as 05 07 01-1 and 05 07 01-2 keep: the 1941 sheets disagree among themselves and none can be shown to rule, so the 1941 arbor's diameters are an estimate, not 020704-1's: the second drawing check, 4-M6); the 1941 drum's chain slot's place along the axis (0207 draws it undimensioned, its middle 4.6-4.7 from the bridge-side face; cut where the laid chain's barb comes, 4.04 from it: 0.6 toward the bridge, 4-M13); the maintaining ratchet's tips Ø 37.45 (05 06 02-1's "war 37,5∅", its tolerance not kept: the revised −0.1 taken); the maintaining spring's width past 270° to its square end; the 1941 staff's turned form (its sheet a blank: the ends, the collet's and rollers' seats as 05 04 02's); the collar's neck drawn flush with the arm (riveted); the escape arbor's cone to its upper pivot and the collet's cone top (scaled); the escape jewels' settings for the 1941 arbor's ends; the stone's pipe from 1.95 to 3.65 under the plate; the block's arm, cove and ledge (scaled on 05 04_1, its width and place from the photographs); the banking screw's size (Wempe 3955's photograph) and its near end in the arm's face; the Exploded view's offsets for the 1941 parts.
- The pillar plate's hand-setting cut: the window's place across the cut, centred on the line through 18 (Wempe 3955's 0.2 off it, within its fit), and the inner face's 12 +0.2 drawn 12.1 on both ends alike; the end arcs' bow, read on the scan at 2-3 px; the bush in 18 (no number on 05 08 02, its bore and sink from Wempe 3955's photograph). Its bore across the plate and the rim's notch not built (How each frame part was measured).
- The pillar plate's thickness, 3.35: its sheet's "3,35 ±0,02 stark" is struck through with a replacement that's no longer legible.
- Screw heads and lengths (no WN sheets in the set), measured on the coloured section and Wempe 3955: pillar screws (WN-57; the dial side's unlabelled) head Ø 6.4 × 3.0, shank 7.7; movement ring screws Ø 6.2 × 3.05, 6.3 (2.25 high until 17 October 2026); barrel bridge screws WN-55 Ø 6.4 × 3.0, 6.2; the click's screw WN-22 head Ø 4.5 × 2.1, shoulder Ø 3.19 × 2.61 (a close running fit in the click's 3.2 +0.03, 0.025 clear: estimated; Ø 3.1 × 2.65, scaled on the coloured section, until 28 October 2026: the second drawing check's 8-M6, 8-M8), thread 3.2; the fusee bush's WN-34 Ø 2.1 × 0.45, 3.2 (ending 0.4 short of the recess; 3.6 until 17 October 2026); the upper cock's screw WN-55 Ø 6.4 × 3.0, 6.2 (blued, as Wempe 3955's); the lower cock's WN-53 Ø 5.8 × 1.7, 5.0; the intermediate bridge's WN-52 Ø 4.2 × 1.9, 4.7. the balance's setting screws (upper WN-55, lower WN-18) Ø 2.5, the upper 1.3 high, the lower 1.4 (Wempe 3955 gives the upper ones' Ø 2.5); the stud's screw WN-11 Ø 2.3 × 1.6, through the cock to 0.6 under it; the hub's screws WN-10 countersunk Ø 1.8 flush in the arm's top (17 October 2026). Their WN numbers are the coloured section's labels where they could be read (the detent foot's screw WN-13, the block's WN-15, the wire spring's stud WN-27: likely); the ring screws' WN-56 on the general arrangement's print (below). The section's print in Klassik Uhren 3/2006 (31 October 2026, below: Sources) reads the labels the coloured scan left open: the upper setting screws' "Schraube WN-55" (sure) and the lower ones' "Schraube WN-18" (sure: its leader ends in the head under the lower setting), and "Schraube WN-56" on the movement ring's screw (its leader's dot in that head, on the print and on the coloured scan alike: sure), the dial side's pillar screw unlabelled; renamed so (Closed).
- Hole 4's oil sink on the top plate's outer face, Ø 4.3 spherical (its depth 0.95, two cones), from Wempe 3955's photograph (no sheet draws it; the second drawing check's 9-M11; also under "From Wempe 3955's photographs").
- The escape settings' screws' bearing: the WN-es heads (Ø 2.6 at 3.525) lap the upper endstone setting's rim by 0.07, the WN-ec (Ø 2.6 at 3.525 on the 37° line) the lower cap's by 0.075; no sheet sizes the heads or the settings, and Wempe 3955's top plate shows its heads (2.5 across, 6.94 apart) lapping a Ø 4.5 setting by about 0.03 (9-M14): a sliver, as on the real one.
- The pressed pieces' interference: the bushes WN-300, WN-301, WN-302, 05 08 02-2 and WN-hs, the seconds jewel's setting 05 05 04-2, the motion work's studs, the stop pin 05 08 01-5, the ring's pin WN-202, the dial pin and the plate's pin WN-201 are pressed (their sheets hatch or call them so) but no sheet sizes an interference: each drawn 0.01 over its hole on the diameter (line to line or a few µm loose until 28 October 2026: 8-M11, 9-M7). The plates' pillar seats (0,3 +0,03) and 26's lip (0,5 +0,05) stay at their least: at their middles the plates would stand 18.97 apart and every arbor's endshake change (9-M10).
- The stud's screw hole in the upper cock (05 08 03-1 draws none): M1.4 tapped through the arm's thin end, 4.1 along from 23 toward the foot and 4.2 across toward O, from the lever chronometer's same cock 127-556.04 U30, its only figures (the owner's choice, 28 October 2026, O-8); Wempe 3955 reads 4.22-4.33 along and 4.25-4.36 across (2_Wempe_3955_A.jpg, ±0.15), which can't tell 4.2 from 4.35. The stud built off-centre about it as 05 03_9's plan draws it (scaled: likely). The balance's setting screws are named WN-55.ck after the coloured section's label "WN-5?", whose last digit (5 or 6) its 5-6 px digits can't settle (the second drawing check's 8-M14: one WN number for the upper cock's M2.6 and these M1.2 is unlikely, so one label differs; undecidable). The section's print in Klassik Uhren 3/2006 reads it "WN-55" (sure, 31 October 2026): the name stands.
- The threads' form (26 October 2026): the sheets give each thread's size (M2.6, M2, M1.7, M1.4, M1.2), not its form or fit, and no photograph in the set shows a loose screw's thread. Every screw's shank is drawn as a right-hand ISO metric thread at its size's coarse pitch (ISO 261/262, DIN 13; M1.7 0.35, M2.6 0.45:
KIT.isoP), ISO 68-1's basic profile (60°, the depth 0.541 p, flats p/8 and p/4), at 6g's maximum material (its major diameter less es = 15 + 11p µm: an allowance of 7.5 + 5.5p µm on the radius), run out to its root over the pitch before its 45° tip. A size the sources leave estimated keeps its estimate (the case's M3-M6, the 6MX's contact's). The tapped holes of the frame (the plates', bridges', cocks' and bushes' tables, the pillars' ends, the detent block's M1.7 and the wire spring's stud's hole 5) carry the inside thread at 6H's minimum (the basic profile), running out over a pitch to the drilled hole at each face, so screw and hole are the allowance apart radially all round; each screw is turned on its axis to lie on its hole's helix (KIT.matchThreads: 43 screws in all the versions). Other tapped holes (the movement ring's, the dial screws' in its flange, the fusee's, the balance's masses', the case's and the 6MX's contact's) stay plain bores at the thread's size and 0.02, the screws in them threaded. Standard practice, not read off a Wempe: sure of the sizes, estimated in form and fit. - The 6MX's dial screws' sinks (7 November 2026): Kirov No. 247's and No. 2973's dials show a dark ring round each screw's head, its inner edge the head (Ø 1.64-1.88, the slot across it) and its outer edge onto the paint Ø 2.21-2.43 (6mx-audit/gamma.md,
dhead.py, each dial at its arbors' scale: likely). Its form isn't seen: the 6MX's sink is drawn as the drawings' Ø 1.8 opening in a 45° chamfer to Ø 2.3 at the face, 0.25 deep (estimated: the more conservative of a chamfer and a wider bore); the drawings' sink (05 02 00-4) is unchanged. In the same audit the 6MX box's badge was centred in its tier (Kirov 247 and 2973) and the outer box's catch drawn at its own reading's Ø 26 (Kirov 247's single oblique frame reads about 29: doubtful). - Steady pins' length, 3.0 (1.7 in the part, 1.3 out): U30 draws the upper cock's so; the others are taken the same. The cocks' pins carry no WN number on their own sheets; the coloured section labels the upper cock's "Stellstift 4 WN-203" (the second drawing check's 8-M6), and the lower cock's are taken the same.
- The movement ring: the lip's depth under the seat (2.0) and so where the cone starts; the M2.6 holes at the thread's size through the band and the flange to the cone (the sheet sizes only the M2.6; tapped that far or drilled clear above the thread isn't drawn), with a 5 µm step 0.3 into the flange where the cut starts; the plate's pin 5.35 long with its top 0.1 under the plate's face (the coloured section draws it 7.6, which would cross the cone); its material brass ("——" on the sheet; the coloured section colours it yellow, GUB 12255's is gilt; weighed at brass's 8.45) and its finish (nickel, as Wempe 3955's looks).
- The pillars' countersinks (Ø 2.6 at the face, 90° to the tap drill: 2.59 scaled; the thread cut through them) and relief grooves (out to r 3.25, 0.35 deep, half-round): drawn, not figured.
- The balance opening's tongue in the top plate, 2.5 wide ("2,5": sure): its axis toward 113.5°, passing 0.85 S of the opening's centre, its round end r 9.0 from it (likely: ±4° on the axis, ±0.3 on the end). 05 08_1b traced (the opening's circle fitted, 9.81 px/mm, the sheet's N up by holes 51 and 26): its sides 115.5° and 111.8° over their length, the end's arc round a centre at 119.7°, r 7.74 (its far point r 9.06), the sides' outer halves alone 118.4-120.5° (the drawn mouth widens toward the opening); "50°" is from the pocket's dashed S edge to the tongue's N side, which the pocket's edge meets. Wempe 3955's top face (
12_Wempe_3955_obere_Platte_oben.jpg, 11.43 px/mm on 8 holes): axis about 110°, 1.1 S of the centre, 2.85 wide, its end r 9.2 (8.6 read again by eye). Until 18 October 2026 its root 50° round from the pocket's line and its end 8.6 toward 112.5°: the axis toward 93°, 2.4 S of the centre, its end r 8.54 (estimated). The pocket's S edge, the tangent to the opening, runs from 51 to the tongue's N side; the crescent it would leave beyond the tongue's S side isn't dashed on the sheet and isn't cut. - The intermediate bridge's outline, 45.5 × 10.0 with round ends, 3.8 thick, its screws' sinks Ø 4.7 × 2.0, its pins' holes 2.5 deep: scaled on 05 08 04, the sinks' Ø on Wempe 3955's dial side (
3_Wempe_3955_uZ.jpg, 8.6 px/mm on holes 3, 12, 40, 30, 18 and 26: 4.7 ±0.1, likely; Ø 4.4 until 18 October 2026), their depth estimated. The same photograph measures the outline 45.7 ±0.3 × 9.75 ±0.15 with semicircular ends: the form confirmed, the sheet's sizes kept. Its section measured at 6.9 px/mm by its 3.8 (likely): the bush's hole Ø 4.3 with a 45° mouth from the plate side, Ø 5.7 at the face, to the bush 0.7 in; the seconds jewel's setting the bridge's full thickness less 0.2 at the plate side, Ø 5.2 outside and Ø 3.7 inside, the jewel 1.75 in, a straight recess Ø 3.7 under it to the dial face (until 15 October 2026 both sunk Ø 6.2 from the plate side, 0.7 and 1.7 deep, and the setting closed under the jewel to Ø 1.1). - The click: its base 2.85 under the hole (the Ø 5,7 circle tangent to it; the scan draws 2.79-2.81), the centre of its back's arc (fitted), its beak's front face, and its turn on the bridge (23.3° from N, ±3°, on Wempe 3955).
- The upper cock's relief: the 45° step runs from r 12 on the full underside in to r 11.2 on the relieved one (26 October 2026: the "12 r"'s extension line comes down from the full underside's corner on both Schnitt A-B and U30, U30 at 49 px/mm puts that corner at r 11.98 and the step's top about 11.35, and the plan's hidden arcs read about 11.5 and 12.3; until then 12 to 12.8, which side inferred). Hole 20 (Ø 2.8 at 10, out to r 11.4) then cuts the step's top 0.2, as U30's section draws its edge at the step's corner. Its two M1.2 holes are tapped (26 October 2026) at 3.525 from the bore, the middle of 3,5 +0,05, into the Ø 6 boss under the relieved arm (the "6 Ø" is a boss, not a sink: the second drawing check's 8-M6).
- The dust bush's flat faces the upper cock (inferred from the cock's place, above), confirmed on Wempe 3955 (
2_Wempe_3955_A.jpg: its normal about 256° ±5 against the model's 255°: sure). - The pillar's body Ø 8.1 −0.2 (05 08 00-1, read "8,1∅" with the ∅ written high; 8.06 scaled at 5:1: likely; Readings corrected, 05 08_11).
- Rough readings recorded, not adopted (the survey of 16 October 2026, PLAN-wempe-estimates.md's appendices; the user's decision: record them, keep the model's values): the pillar plate 3.40 rather than 3.35 (the seconds arbor's 24.1 −0.1 of revision 24.3.48 and its jewel's 1.7 leave its endshake −0.05 to +0.05 at 3.35, 0 to 0.10 at 3.40; against it the coloured section draws the pillar plate about 0.1 thinner than the top plate); the intermediate bridge's steady pins about 4.5 long (1.3 proud, about 3.2 in blind holes about 3.2 deep, 05 08 04's section) against 3.0 and 2.5; the box rim's lining lip (Lange 1947's wall top in two steps, outer 7.4-8, inner strip 4.4-4.6,
drouot_33810142_lange1947_2; Wempe 4585's open lid shows a rebate; its height unreadable); the barrel lid's screws WN-21, heads about Ø 2.2 × 0.75 against 2.6 × 0.5 (hidden in the model); the box's floor about 14.5 ±2 (51 00_1) against 12.5; the glass about Ø 116 ±2 (Wempe 6161's rim, about 4.6 wide) against 112. - The cork ring's sizes, Ø 16.1 × 3.86 on the neck: scaled on the coloured section, a pictorial drawing (likely; the bush's own figures scale to 0.1 on it). Its bore drawn 0.01 clear of the neck. Its density in the weighing, 0.24 g/cm³, natural cork's.
- The bowl's thread, rebate and notch (24 October 2026): none is on the casting's sheet. The thread's pitch 0.75 read on a 6MX's rim (±0.05), its size from the bezel's traced bore (±0.2), its form the ISO basic profile (60°, 0.406 deep) and the clearance 0.03 estimated, right-hand (estimated); the rim's height the flange's 4.7, the rebate 0.05 clear of the flange, the run-outs 0.5 (estimated); the notch 1.8 wide (the pin's Ø 1.6, 0.1 clear each side) down to 0.8 over the seat, cut through the rim as on Kirov-Poljot 24020 (its depth there not seen: estimated); the radial pin 1.78 out of the flange so its end clears the bezel's thread's crests (the coloured section reads 2.0 ±0.2). The casting placed by the reading that its top is the rim round the flange, which puts the bottom where 05 06_01 gives it (49 from the seat) once faced 0.7; the cork ring drawn 3.70, squeezed, against the section's 3.86. Since 8 November 2026 the 6MX's own thread is pitch 1.0, read on Kirov 247's rim (0.9-1.2, likely: the 6MX case review); the drawings' bowl and bezel keep 0.75, from Kirov-Poljot 24020's, which the later 6MXs may have.
- The bowl's winding-hole seat (15 October 2026; the 6MX's only since 24 October 2026, the drawn bowl's bottom meeting the cork: above): with the movement in its bowl as drawn (the bore 53 deep, R-05 01 00-1; the movement ring on the flange) the cork's top is 3.84 over the bottom round the winding hole, so on the drawn bowl it would seal nothing. The casting's sheet draws no hole and nothing machined. Two 6MX bowls have a raised seat round the hole inside: moMvyx8eXfo 3:35 (1080p, the bowl empty in hand), a flat-topped ring (that it stands, sure) 72 px across against the hole's 38.5 in the same frame, so Ø 15.3 by the hole's 8.2 (likely; the cork's 16.1 nearly), its top an ellipse 60 by 72 px, so seen 34° from the axis, its near wall 8.5 ±1.5 px at the bottom's scale, about 4.5 px/mm (the rim's 5.26 less the 53 mm farther), so 3.4 ±0.6 high (rough); DIxob2Rl4dc 5:09 (480p), a pale ring there, so perhaps a pressed bush. The Wempe's bowl is given that seat, Ø 15.3 round the hole's 8.2, drawn 3.84 high to the cork's top (estimated: inside the video's height; the cork's purpose). No photograph or video of a German bowl's inside was found (UhrenJust's Part 6, WCguXfdZ38E, puts the movement in dial down).
- Finishes: the plates, cocks and bridges gilt as Wempe 3955's (the sheets give the metal, not the finish).
- From Wempe 3955's photographs, not on the sheets (16 October 2026, the audit of 3.00.00): the maker's engraving on the top plate's outer face, "Gerhard D. / WEMPE / Hamburg", centred at O 30.6 N 8.6, its lines 8.7, 9.85 and 7.4 long and 1.2, 1.7 and 1.2 high (2_Wempe_3955_A.jpg at 7.74 px/mm; WEMPE drawn filled where it is outlined); "RGG" in a triangle stamped on the balance arm, 2.2 across, 11 out (15_Wempe_3955_Logo_plus.jpg, oblique: estimated); hole 4's spherical oil sink Ø 4.3 on the top plate's outer face (its depth 0.95 estimated, two cones); the detent block's steady-pin holes drilled through the top plate and countersunk Ø 1.4 on its outer face (blind 1.4 from inside until then); the dial screws' M1 holes through the movement ring's flange (2.5 deep until then); the hand setting's holes 14-18 and its square window 6.5, centred 30.9 out on the line through 18 (struck through on 05 08 02-1, but Wempe 3955's plate is drilled for it, each hole where the table puts it).
- The build checks' figures (Building it): the guard band, 180-270° over the wind (185° until 19 October 2026's physics pass) (wempe_escapement.js's, 14° under the reference's swing: no source's; 193° until 15 October 2026); the mainspring's strip ±0.005, the detent's and gold springs' ±0.005, the hairspring's strip ±0.003 (boxed, no tolerance written) and its cut length ±0.3, the holes' places ±13 µm (the tables give none), the banking as first set ±0.02 and the preload by eye 0.8 ±0.3 g (0.63 before the physics pass), and as the bench leaves them ±0.005 and ±0.05 g, the endshake set again within 0.01 of its drawn figure; the endshake stacks' undrawn terms (the top plate ±0.02, the seconds jewel's depth 1.75 ±0.02, the escape arbor's endstones 22.84 ±0.02 (22.82 until 25 October 2026), the fusee bush's 0.75 ±0.02, the barrel's bearings 3.29 ±0.02); the endshake band 0.01-0.08 (free in the cold with an oil film, to the Hamilton manual's 0.003 in); the lock's shallow end, 0.232, from the frame's 116 µm taken the same at every depth (0.154 from its 77 µm before the physics pass); the preload's aim a quarter into its window; the banking's aim the lock window's middle, set again until it reads inside; the maintaining spring's 5-minute floor; the timing weights' reach (their size estimated, drawn against their heads); a drawn tolerance taken as made anywhere within its limits.
- The escapement of 1943 (the Variants' fourth version; The escapement of 1943 above): the banking screw's dome rising 0.4 on its 1.1 cylinder (no photograph shows the rise), its length 8.2 under the head (the 6MX's loose block's), so its threaded end 2.9 past the upright's far face (no German photograph shows that side), its underside where the pipe rests (as the 6MX's). Its block's stud (29 October 2026): its height, 2.5 proud, and its M1.7 3.0 into the block the 6MX's (the plans show only its slotted face; DEC 422's S view puts its top about level with the pillar screws': possible); the near steady pin 1.2 into the block, the 6MX's; what clamps the block, no photograph.
- Wempe 3955's set-up ratchet recess: 0.7 deep, its wall at 45° (only its two edges, Ø 8.7 and 7.3, are measured).
- The 6MX's domed screw heads: 2.4 overall with a 0.8 dome (±0.3), read on oblique views against the model's head of the same width; their thread and shank the drawings'.
- The 6MX's cork ring 2.4 thick (its top 1.6 under a 3.86 one's; ±0.3) and its waisted dust bush's flare taken as a cone; the 6MX's detent block stud screw 2.5 (±0.7) proud; its barrel arbor's square end ±0.4.
- Wempe 3955's dust bush waist Ø 9.0 (±0.4) and shoulder height (±0.3), its collar 1.85 (±0.2); its fusee square's tip ±0.5.
- The hammered finish's tile: its statistics measured (scale, spread, orientation), its pattern synthesised.
- The hairspring's collet bored on its sheet's 1:70 to the 1946 staff's seat, Ø 1.647 at the arm's face to 1.604 (25 October 2026 the size, straight Ø 1.648; tapered 27 October 2026): its sheet, 05 03 02-2 (24.2.43), gives 1.6 H7 on 1:70, tapering to 1.55, the earlier staff's; on the 1946 staff's seat (05 04 02: 1.58 to 1.65 s6) such a bore would seat 3.15 higher, where 05 03_5's 13,4 and 0,75 put the collet on the arm. The collet is bored to the seat, as the impulse roller's 1.627-1.65 bore is, and sits 0.05 over the arm; a maker opens the collet to the staff (no effect on the rate).
- The top plate's bushes for the intermediate and seconds arbors (WN-300 at 38 and 35, no WN sheet): bored 0.845 and 0.83, each 0.02 over its pivot, for 05 05_1's "Lagerstellen: Enger Laufsitz" (the centre arbor's WN-301 1.21 on its 1.19); 0.86 both until 25 October 2026 (the per-part audit). The change pinion's root Ø 5.4 (Wempe 3955, ±0.1) leaves 0.05 under the hour wheel's tips, and the up-and-down pinion's 0.035 under its wheel's (the sheets' own figures): depths a maker must watch; no check measures the motion work's depthing (gearing.js takes the going train).
- The mechanisms in turn (25 October 2026,
wempe_wear.js,wempe_overwind.js,wempe_motionwork.js,wempe_estimates.js): the wear coefficients (Rabinowicz's classes, the escapement's as dry non-metal on metal), the hardnesses' soft ends (333 gold hard rolled 150 HV), each contact's area, slide and the tolerance taken for it (the barrel drum's line 0.10, the chain's 1 % of its pitch, the fusee wheel's teeth 20 µm, the escape tooth's tip land 0.02 and its wedge 0.5, the balance pivot's flat end), the gold spring's loads (about 10 and 2 mN); a hand's torque carried on past the data to the Ø 34.5 paddle; the key's coil wire (a design value: Ø 0.68 or more, spring wire EN 10270-1 DH), its drag back 5 mN·m; the studs' shake 0.02; the cannon pinion's bench weight 30 mm along the hand; a hairspring strip drawn 6 % long; the TF range 80-200 s.
From the parts audit (3 November 2026): 3
- The staff's lengths (25.6 overall, the pivots 6.9 and 6.1) are taken from 05 03_3.2. That sheet is the post-war Glashütte production's (12.3.65, no Wempe title block, tempered 210° against 05 04_4's 240°), not a revision of this chronometer. No Wempe sheet gives them, since 05 04_4's top is cut off.
- The banking screw's head is Ø 3.15 (Lange 5177's, the smallest of the photographs' 3.15-3.6), to clear the detent with its hole centred.
- The strap screws' head, Ø 8 × 2.0, is DIN 97's proportion for 4 (the standard isn't in the set).
The train (P1b): 11
- the intermediate and seconds pinions' cut leaves: tips Ø 4.72 and 3.17, roots Ø 2.87 and 1.70 (likely), by the escape pinion's sheet, the only one that gives a pinion's cut figures beside its turned head (05 04_8: head 3.13, tip 2.97, root 1.6 for z 10, m 0.263, so d + 1.89 m, d + 1.28 m, d − 3.93 m): the Ø 5.0 and 3.4 scaled on the intermediate's and seconds' sheets (4.9-5.2 and 3.36-3.57) are their turned heads (d + 1.89 m: 4.93 and 3.34). Until 18 October 2026 the tips the heads' 5.0 and 3.4 and the roots 2.75 and 1.61 (the centre pinion's 2.13 m dedendum). The meshes' efficiency tooth by tooth rose with them (gearing.js: the train 0.780 against 0.749's rule, escphys.js's ETA unchanged: PLAN-wempe-estimates.md, B.5);
- the pivots' finished lengths (3, the kompl. sheets', taken for the last-revised pinions too) and the centre and intermediate pivots' tapers (both read 1:90, the figures re-inked or unreadable; the centre's 1:30 until 25 October 2026); which end of the centre arbor's 1:30 journal is the larger (the collar's, where both sheets put the 2.2 and as the shank's 1:80 runs; 05 05 03-2's outline 1 px wider there, under the 2.2 px the taper would give) and WN-302's bore following it (0.026 clear);
- the seconds jewel's depth drawn 1.75 (05 08 04's 1.7, no tolerance), so the seconds arbor has 0.05 endshake; the centre arbor drawn 19.03 (19 +0.05) and WN-302 0.1 under the face (0.1 +0.02), so 0.07;
- the riveting collar above the centre wheel's seat (05 05 03-2's 1.6 −0.1 the seat alone, drawn 1.55, and the collar on to the framed 19: closed 16 October 2026); 05 05_1's layout's lesser figures beside the detail sheets that supersede them: its 17 to the centre wheel's top face (05 05 03-2's 17,2 +0,05 puts it 17.26), the top bushes' oil cups drawn about 0.9 deep at the bore against the estimated 1.2, a small chamfer where each bush meets the plate's inner face (not built: the plates' holes are batch 8's and 9's), and its unattached "5,5 Ø" at the seconds' top bush (nothing of that size on Wempe 3955's plate) (the second drawing check's 6-M12, F6);
- every bush's bore (the pivot and 0.01-0.025: "Lagerstellen: Enger Laufsitz"), oil sink (spherical, Ø 4.55 × 1.2 in the top plate running out to the bush's rim with no flat: Wempe 3955's top plate,
12_Wempe_3955_obere_Platte_oben.jpg, 4.46-4.69 at holes 1, 38, 35, sure that no flat shows, likely on the size, the depth estimated; Ø 4.0 with a 0.3 flat until 18 October 2026; Ø 3.7 × 0.9 in the bridge; on WN-302 a spherical cup Ø 3.8 × 0.55, its form drawn on 05 08 02 and its size scaled in a schematic 2:1 section) and length beyond the plates' faces: the WN standard parts have no sheets in the set; - the seconds jewel Ø 3.6 × 1.1 (scaled on the coloured section, a pictorial section) with an olive hole Ø 0.78, its oil sink on the dial side Ø 1.7 × 0.6 (the section's, ±0.1), and its setting's form (a tube the bridge's thickness, burnished over the stone, open under it in a straight recess Ø 3.7 to the dial face: 05 08 04's section, likely; a floor under it with the post's hole Ø 1.1, the coloured section's, until 15 October 2026);
- the studs' diameter, Ø 1.5 (05 02_1 at 5:1 scales both 1.52, the pipes' bores 1.50-1.56 on 05 02 02 and 05 02 04; Ø 1.3 until 15 October 2026, scaled on 05 08 02 at 2:1), their domed ends (05 02_1: rising 0.3) and the second stud bush at hole 19 (drawn dashed in 05 08 02's Schnitt A-B, taken as another 05 08 02-2);
- the wheels' riveting: each seat its sheet's length, standing past the hub as turned, before riveting (the rivet's spread into the hole isn't drawn; the centre arbor's collar with its groove); the seats and holes line to line at their nominal sizes (the n6/H7 presses' interference isn't drawn);
- the cannon tube's punched dents (05 05 03's "Körner" over the tube's groove): three, 120° apart, each 20° round and 0.4 high, pressed into the shank's groove line to line (their number, size and place estimated: the sheet draws the mark, not the dents; the tube held by nothing until 28 October 2026, 6-M6);
- the centre arbor's shank groove under the punch (05 05 03 of 1943, scaled: 0.24 deep, 0.63 high) and the crown's sphere (r 3.1, from the arc's 0.35 rise over the 2.86 the side view shows);
- finishes: the wheels gilt and the arbors bright steel, as Wempe 3955's (
8_…Räderwerk_plus.jpg).
The fusee and barrel (P1c): 12
- the mainspring's length, 1,240 mm (not drawn anywhere): fitted to 05 06_20's measured force through the drawn fusee (Physics: energy), good to about ±50 mm (GUB 12255's barrel opened and let down, UG44DSWMv3o 0:26 and 5:56 at 19.7-20.8 px/mm on the 38.5 bore, holds about 13 coils on the wall at 0.40 and 3 free turns, about 1,530 (1,360-1,700, rough), a post-war movement whose spring may be a replacement; solved at 1,530 (set 0.6 and 0.7, 16 October 2026) it fits 05 06_20's curve three times worse, rms 3.3-3.9 % against 1.07 % at 1,240 mm and the same set, and doesn't raise the level, 0.753-0.802 against 0.802: kept); 1,386 until 15 October 2026, half the room between the core and the wall, the usual rule; its height drawn 14.8, not 15: the 1948 drum is 14.95 inside under its lid (0207's 15.8 ±0.1 space is the 1941 barrel's); its shape (two packs and a turn between);
- the band's width, 0.78 (a post-war GUB's band, about 0.2 mm² across, gives about 0.8-0.9 at the sheet's thickness: rough, agreeing; The fusee: the band); its hooks' outlines, approximated on their figures; the chain's hooks' arcs between their figures (traced, the crown r 1.55, the barb's front), their eyes r 1 as the plates' lobes; the hooks 0.80 thick (05 07 04's side views: the chain's full width), their eyes thinned to 0.26 between the end links' outer plates out to r 1.1 about the rivet (where the step falls isn't drawn); the plates' sides between the lobes (no figure: traced on 05 07 04's plan views, the waist 1.41, 1.38-1.44 over 13, the sides arcs r 0.93 tangent to the lobes); the rivets' ends flush with the outer plates and polished bright (the edge view draws nothing proud of the framed 0.82; Wempe 3955's chain shows them lighter than the plates), their holes Ø 0.56 round the drawn 0.55;
- the stack's 0.05 gaps between parts that rest on each other; the fusee's face at 13.6 of 05 06 04's 13.7 −0.1 (its old "13,6 +0,1" and the new band's common end, the coloured section's ratchet to 6.1 off the plate: with the 0.05 gaps kept, 13.65 would need 0.025); the Vorreiber's face a re-turned to 2.76 (its flange 0.86; its Ø 9.9 relief 0.425 deep under the re-turned face, the sheet's 0,4 +0,05 from face a as re-turned: cut after the re-turn. Until 28 October 2026 this line said the re-turn left it 0.06-0.31 deep, as made at 3.1 or 2.9, which the solid never was: the second drawing check's 5-M6), which the stack under that face leaves; the fusee body's large face re-turned 0.2, set by 05 06 04's "0,5 +0,05" to the click wheel (0.15-0.2 with the body's 12.55 and recess 2.7: the 0.5 taken), so the body 12.35 against the sheet's bracketed (12,3) and the flange's ribs 1.8 over both against its bracketed (1,6), which no single re-turn meets with the 0,5 (a reference carried over from before 1948); the face falling back 5° outside 05 06 04's Ø 33 +0.1 (its angle drawn at the flange's outer corner, one leg on the 33's extension line), its purpose inferred: the face bears on the maintaining ratchet's plate only inside Ø 33, the flange's rim, the chain's pin and the first rib clear of it and of the maintaining detent's tip, which stands 0.15 past the ratchet's face just outside the flange; the maintaining detent at 6.2, the least of its 6.3 ±0.1 (05 05 05 of 1941, not revised with the fusee in 1948; the coloured section draws it at 6.0), so its tip covers 0.85 of the ratchet's teeth (0.75 at 6.3);
- the fusee wheel's tube Ø 6.5 g6 (05 06 00-3 writes "6,6 +0,1" over a struck figure and draws the tube 6.31-6.44; kept 6.5 g6 by 05 06_1's 6,5 H7/g6 under the ratchet's 6,5 H7, 05 06 02-1 as drawn 29.11.40 and unchanged by its revision of 11.3.48: a 6.6 tube can't enter that bore) and bore 4.55 (its "4 +0,1" can't pass the arbor's seat; 05 06_1's 4,45 H7/g6 is a straight seat's fit, and on 05 06 04-1's 1:70 seat, 4.43-4.48 under the wheel, a 4,45 H7 bore would wedge: the 4.55 an estimate, 0.04-0.06 clear on the radius, 4-5 times H7/g6's; the second drawing check's 5-M10 and 5-M15); the fusee body's length as turned 12.55 (12.6 −0.1); the 1,2 taken as every turn's pitch (it is drawn once, at the first land) and the first turn's rise out of the flange's slot (a cubic, level at the hook); the slot's deepening under the chain's pin read as a slitting cutter's (its depth scaled on section A-B), the pin 0.17 rad behind the groove's start (where along the flange the groove starts isn't drawn);
- the chain's pin's angle along the flange (0.17 rad behind the groove's start; its radius, 1 under the ribs' tops, is the sheet's) and the hooks' throats round it;
- the stop work (05 06 03, no sheet): the bar's slide at full wind, 3.36 (the chain's,
wempe_stopwork.py) against C-D's figured 3,2 (the lower end's way between its two drawn positions; the positions themselves scale 3.54-3.66, so the drawing isn't to scale there and the figure rules): 0.16 over (the second drawing check, 3-M15, likely). Not corrected, because C-D's figures can't all hold on the model's fusee: the 22,5 bar with the "2" (its upper far corner r 12.5 running) puts the lower point at r 12.36 running, where the "1,76" puts it at 12.26; at full wind the chain on the top turn (05 06 04-2's groove, figured) holds the lower end at r 9.32, the "1,2"'s 9.3, so the slide is 3.36 with the drawn bar and 3.26 with the lower point at the 1,76 (the upper corner then 0.1 past the "2"); 3.2 itself would want the chain's contact on the top turn about 0.06 further out than the figured groove puts it, or the upper corner 0.16 past the "2". Which of the four figures gives way isn't settled by any sheet; the stop's function doesn't depend on it (full wind is where the stop pin meets the bar, which the chain's push sets the same either way); the cap, 3.6, is the drawn positions scaled. Also the bar's thinner upper part, 1.05 from u 0.8 (its thickness from the coloured section's 0.70 of the middle (9.5 px of 13.5), its start so its full thickness stays inside the small end's recess across its 3.6, since the slot is 1,1 deep from the recess out on that side; u 3.4 until 31 October 2026); the spring's height, 1.0, a design value (no source draws its section: the coloured section leaves the recess between the bar's end and its wall uncoloured, where it colours steel blue; the 5:1 fusee sections 05 06_1, 03-1 and 03-2 draw the earlier stop, a post at the small end; no 05 06 03 sheet is in the set; no photograph or video found opens a fusee: the GUB restoration, ZEc91vwppVk and WCguXfdZ38E, keeps its cover plate on). Anything from 0.9 (its pin's Ø 0.5 hole through it, 0.2 of strip either side) to 1.5 (under the recess's 1.6, 0.1 off its floor) works: its stress is the same at any height, 750 MPa wound against hardened spring steel's 1,200-1,800, and its push, linear in the height, is 0.054-0.12 N half way over that range, 37 times or more the 0.5 g bar's sliding on the cover plate (wempe_strength.js); the bench's stop work test (wempe_bench.js) has a maker check the bar springs back and the stop holds full wind. Its thickness, 0.10, worked from its bending (the stop work), and its shape between the two drawn; its pin's height, mid-spring; the bar 0.02 off the chain where it presses it; the stop pin's fit and its outer end flush with the plate (its length is scaled off the coloured section, 1.85 ±0.1: the stop work; anything from 1.24, to bear on the bar's whole thin end, to about 6, short of the chain on the fusee's fourth turn, would work: a strong hand's 1.06 N·m on the key, Swain 1970 as overwind.js takes it, puts 76 N on it 0.7 out, 134 MPa); - the maintaining detent's arbor (05 05 05-2, no sheet: Ø 2.25, 18.95 between shoulders, pivots Ø 0.88 × 3.1; its shoulders' 0.25 × 45° chamfers and its pivots' domed ends, rising 0.35 at the lower shoulder's end and 0.25 at the other, scaled on 05 05_11, likely; its seat tapered 1:70 as the detent's hole (05 05_12's "Kegel 1:70") over the detent and the 1.2 it was knocked along, the body straight either side at the taper's ends, 2.233 and 2.279: 28 October 2026); its wire spring (Feder 05 05 06-1, no sheet: its hole is the top plate's 5, "Drahtfeder", M1.7) and its stud, measured on the north-side photographs (4_Wempe_3955_N, 4_Kirow_247_N, 4_Lange_5177_N, scaled by the hole table's spacing of holes 3, 4, 5 and 49) and from above (2_*_A), checked on the coloured section (9.37 px/mm by the plates' 19): the stud a plain slotted cheese head Ø 3.0 × 1.9 (2.6-3.5 and 1.8-2.0 on the three, the section's 3.4 × 1.87: likely ±0.3, ±0.15), its slot 0.45 × 0.7 (likely) turned 10° as Wempe 3955's (it varies), steel (Wempe 3955's is brass coloured), its shank 0.4 out under the plate with its end rounded (the section: likely), the wire in a hole 1.5 deep in that end (estimated); the wire steel Ø 0.25 (0.24-0.26: likely ±0.05), to 1.8 over the pillar plate (the section; the photographs 1.2-3.3: likely ±0.4), drawn upright across the detent (the section; the photographs lean it 1.8° and 2.9° toward the arbor and 4.9° away, a set given by hand) and bent out by the detent's back, which stands 0.32 over its axis at hole 5: 0.31-0.51 mm at the arm's upper corner as the detent rides the teeth, a cantilever 12.3 long, so with steel's 206 GPa it presses the detent with 0.020-0.033 N (its root stressed 160-270 MPa);
- the maintaining spring's pins drawn Ø 1.2 in their 1.2 holes (020605: 1.25) (its swell round its pin traced on 05 06 01-1 since 15 October 2026: 3.4 at 288° and 4 at its end were estimated); its outer edge's run into the eye, an arc tangent to the ring 60° from the eye (the sheet's line comes in over about that, within its own ±0.08: the angle estimated; 27 October 2026); the click springs' holes on the strip's middle (05 06 02-2's 0,8 −0,05 from its edge at its lower limit);
- the clicks' screws (WN-21: put in from under the ratchet, the shoulder Ø 1.19; its M1.7 an ISO thread at 6g in the plate's tapped hole, 27 October 2026), the click wheel's screws (WN-19, heads turned to the holes' 1:8; their M2 an ISO thread in the body's tapped holes, and the cover plate's WN-20's M1.7 in its, both tapped since 28 October 2026, the second drawing check's 5-M11 and S-6: plain until then), the cover plate's screw (WN-20, countersunk, 3.5 into the body's 6); the Vorreiber's pin (05 06 00-5) Ø 1.16 × 8.3 in the hub's and the arbor's holes reamed together, Ø 1.15 (the sheets' 0.8, 1.1 and 1.2 reconciled: the arbor, above), its taper not drawn; the chain's pin (05 06 00-6) pressed, Ø 0.567 in the ribs' 0.555 (its own figure isn't in the set; 0.0025 clear until 28 October 2026); the tapped holes drawn flat at the drill's depth (the M2s at 6.25, the middle of 6 +0.5), and the M2s' angle on the body read off C-D (likely ±2°); the click springs' rivets' heads (05 06 02-4, "Niet": domed, 0.2 high as 05 06 02 draws them, Ø 1.0 estimated) and their formers' tangencies 15° apart (02-2, likely ±2°) and the tip's place where the 27.0 ends, 113.6° from the hole against the figured 110° (likely) and the 1.7 sink and 2.2 opening of the clicks' holes on the faces first-angle projection puts them on;
- the hook block and the Steg (built as their sheets draw them on 18 October 2026: the barrel, above): the rivet's place on the block, 1.4 from its far end (0207's plan, scaled: likely ±0.5); the strip's end on the block 0.3 short of its far end, its last 5.7 lying on it (the hook's form and the strip's hole aren't drawn); the Steg's ends flush with the bottom's and the lid's outer faces (0207's section: likely); the 1941 lid's and bottom's slots for it (2.025 wide, open to the discs' rims to r 18.35 as 05 07 01-2 of 7.4.41 draws the lid's 9 o'clock notch, since 28 October 2026: closed 2.025 × 0.55 before, estimated); the Steg's 0.5 in the 1948 drum's 0.8 slot (05 07 01-1's revision b widened the slot, "war 0,5": the coloured section draws the Steg 0.45-0.55 thick, so the slot's width doesn't make the Steg 0.8: the second drawing check, 4-M12, closed); and the drawn spring's bends under the Steg and the block's ends (over 0.25-0.4 rad, as the solve's states step: tools/wempe_mainspring.py). The block's length is 0207's dimensioned 6 (the later sheets scale 5.1-7.3). The chain's slot in the drum (cut at the fusee's assembly, 0207: 2.5 × 0.85 through the wall) cut where the laid chain's hook puts its barb, and the band's where its hook does, one drum for each (since 25 October 2026). The 9 o'clock slot of 05 07 01-1 (revision a of 11.3.48: 2 +0.05 wide, "0,95 +0,15", "18,3 +0,02" struck; revision b of 20.4.48: "0,8 +0,05", was 0.5 +0.03) is the Steg's, through the drum's bottom at r 18.3-19.1 (sure: the section draws it through the bottom just inside the bore, the plan its outline from the bore's 0.15 in to 18.3); from 17 to 18 October 2026 it was cut through the wall from the rim and read, with the lid's 9 o'clock notch, as one slot for prising the lid out. The lid's 3 o'clock notch's use isn't drawn (prising the lid out: likely; since the drum's insides were turned to 0207, 25 October 2026, it lies at the chain's slot's angle, 1.8 from it along the axis);
- the set-up ratchet's teeth face the way the frame's click takes them (README, Unresolved);
- finishes: the fusee, its wheel, the maintaining ratchet, barrel and set-up ratchet gilt, as Wempe 3955's (8_…Räderwerk_plus.jpg, 7_…W.jpg); the clicks, detent and maintaining spring blued (their sheets' 295° and 310°); the click wheel and dust plate plain brass; the click springs bronze.
The escapement (P1d): 15
- The locking stone's place, 7.14 from the wheel at 37.0° from the line of centres (0.235 deep): scaled on 05 04_1 against the tips' Ø 14.00 (likely, ±0.04 and ±0.3°; 7.2 and 36.5° until 19 October 2026).
- The detent block's turn about hole 13, fitted so the stone lands there: the stone then sits 18.74 along from the block's screw row, 0.06 short of 05 04 01-4's 18.8 to its cross screw (18.73 with the blade centred, until 27 October 2026).
- Which face of the block lies on the plate. The front view of 05 04 01-4 is taken as the face on the plate, seen from above as the frame's plans are: drawn the other way round, the base's end that the detent's foot is clamped to would face away from the detent. Its side view is read in first angle, as the sheet reads throughout (DIN's; 15 October 2026, sure): the upright at the free face, 3.5-6.5 under the plate, the banking screw 5.0 under it and the foot 1.3-3.3, as 05 04_1's elevation prints them (the upright 6.5 to its end, 2.8 high, the screw's axis 1.4 from its end) and Wempe 9166 shows them (since 27 October 2026: the escapement of 1943's block; until then read in third angle, the upright flush with the plate and the foot 3.2-5.2, to meet the misread rollers). The block's steady pins' holes in the top plate (not in its table: drilled at assembly) and the stud's screw's tapped hole in the cock (not on 05 08 03-1) are cut in frame.js.
- The detent's heights: its foot 1.3-3.2 under the top plate (3.2-5.2 until 27 October 2026), the blade flush with the foot's lower edge (1436's right view), the pipe 1.9 long (1436's) from the blade's top edge, 2.35-4.25 under the plate (as first drawn 2.0 long, 2.30-4.30: 05 04_1's elevation dashes it from the blade's top line, 2.28, to 4.25, beside the arm set back 1.08; Wempe 3955's still 1.95-3.65, its arm flush with the base's edge as photographed, where the drawn pipe would run 0.16 into it: estimated), its side on the banking screw's head, and the stone standing out of it to 0.06 over the teeth (1.9-3.8 and, as first drawn, in 1943 and the 6MX, 1.95-3.65 until 28 October 2026, from 0.1 under the teeth: drawing check 2's 2-M1; until 15 October 2026 from 3.3 under the plate, 2.0 long). 1436's right view draws the pipe's band from the blade's "unten" edge 1.9 toward "oben", 1.0 past the blade's flush edge: built so.
- The gold spring's tip 1.54 from the staff, traced on 05 04_1, and its bending point 6.15 from the stone, 05 04_1's dashed mark (6.10-6.23 by the plan's scales: likely; 6.7 until 28 October 2026, on the "0,04" figure's glyphs beside it, drawing check 2's 2-M3; the owner's choice, O-6, with the detent's spring's mark, 12.52, for the flexure); the gold spring's head on 05 04_1 drawn 8.40-10.77 from the stone, its screw at 9.57, against the model's 8.18-10.58 and 9.38, 0.19 nearer the stone (05 04_1 is the 1940 layout; 05 04 01-2 draws the part, not its place: within the layout's precision, recorded: 2-M10); its bow round the pipe traced on Wempe 3955's photograph (likely). The horn bent toward the block to carry the gold spring (its curve, 1436's "Anschrägen", traced on Wempe 3955's photograph since 18 October 2026: likely, ±0.1; 1436 draws the bend later, its length not to scale there); its length 4.4 is 1436's figure with Wempe 3955's photograph (likely; 3.5 until 15 October 2026).
- The discharge stone's reach, 1.578 from the staff (1.563 until it was recomputed, 1.5754 with the blade built, until the gold spring's tip's slide about the offset flexure was taken, 27 October 2026), set so the detent lifts the stone 0.305, 0.07 past the lock's 0.235 (the sheet scales 1.7-1.75; 1.547 lifting 0.245 until the lock was re-laid, 19 October 2026), its end bevelled 0.3 so only its leading corner works the gold spring, 0.4 across; the discharge roller's outline (scaled: round at both ends, as built since P1d; 05 04_1's dashes at the stone's end can't be read square or round, and a square end where they end would put its corners at the gold spring's tip) and its material (brass, from Wempe 3955's: likely).
- Which side of the impulse stone the hollow lies (behind its face, where the tooth comes: inferred from the motion; 05 04_1's plan draws it so, about 3.7 long and 2.0 on the tooth's side: likely). A GUB's roller lying loose (Ldzmn4kuKMA 3:53.5, the video review of 27 October 2026, References/wempe/VIDEOS.md) has the hollow's larger part in front of the stone's face, as here: verified, sure (its hollow 2.5 wide against 02 04 02's 3.5, its second hole and its long stone are its own).
- The escape wheel's crossings' turn against the teeth: one under the locked tooth as 05 04_1 draws it (05 04_23 draws its crossing 17.9° behind a tooth's tip; a crossing's place against the teeth is set in the making, not by the form); the meaning of 05 04_1's 86°, 22°10', 6°, 5°, 20° in the wheel is not read (05 04_23's "6,0606∅" is a dashed circle about the centre through the crossing, purpose not written). The openings' arcs' centres 9.43 out (traced, not figured), the floor's step slanting 0.6° (traced), the recess Ø 11.62.
- The escape wheel's collet's diameters, Ø 2.8 and 1.7, its step 1.6 over the wheel and its chamfers 0.15 (scaled on 05 04_7.2: likely). A GUB's collet side-on (Ldzmn4kuKMA 1:20) reads about Ø 2.4 ±0.15 with no step to 1.7 showing, scaled on its pinion's head and the wheel's tips (its wheel end hidden by the crossings): that clock's, not adopted.
- The balance: the masses' height and place read on the sheet and photographs (likely: How the balance and escapement were measured), their chamfer 0.26 × 45° (the plan's ring; the side view's about 0.4); their screws (WN-12: M0.8, the drawn shank's Ø 0.84, its head Ø 1.6 sunk flush in a counterbore Ø 1.62 0.55 deep, from Wempe 3955; threaded through the outer jaw's tapped hole to the rim, as the 6MX's book's Fig. 5.62 cuts a mass; the hole's mouth on the slot's round wall spot-faced up to 0.02) and the tapped hole in each top for WN-12a (M1.2 2.0 deep, its top flat: 05 03_2's plan and the coloured section; left empty, the owner's choice; WN-12a was a nut sunk in the inner face until 18 October 2026), the timing weights' size in Wempe 3955 and the 6MX (Ø 3.8: the photographs ±0.4) and their cuts' depths and width, the timing screws' heads (Ø 1.65 × 1.3, scaled on a poor copy), the punch marks' size and height on the rim's face (the photographs'). The hub's screws WN-10 go in from the arm's top (the coloured section), M1, into the flange's tapped holes (05 04 02's "M1"); the arm's sinks for their heads are read from the coloured section's conical heads, flush: 05 03 01-1's "1,8 Ø H7" (its leader at the side hole) and its "0,4" (an arrow 4.4 from the axis, on no hole) don't attach to a countersink, and its plan rings the left hole only; built a 90° countersink to Ø 1.8, 0.4 deep, in both (possible, recorded: the second drawing check's 1-M10). The staff's seats at their fits' middles (s6, r6) where pressed, the impulse roller's 1:70 bore on its straight s6 seat drawn with its interference (0.009-0.021 on the radius) and the discharge roller's estimated bore at H7's middle (0.005), the hub and the collet line to line on the staff's 1:70; the rollers' and collet's places along the staff as before.
- The hairspring's outer curve the same as the inner, 05 03_7's table, pinned in the stud's hole 3.48 from the staff (3.55 until 28 October 2026, when the stud's screw went to U30's 4,2 across and the stud was built off-centre as 05 03_9 draws it: the owner's choice, O-8; likely); the collet's pin (the same Spiralstift 05 03 02-4) half round and brass as the stud's, its flat 0.005 off the strip in the collet's Ø 0.8 (the strip's end straightened along the hole, as at the stud), 0.45 proud of each side (its form estimated from the stud's; a steel rod Ø 0.22 loose in the hole until 27 October 2026, found by seatcheck.py). The stud (05 03 02-3) has no slot: its plan's dashed lines, 1.87 apart, are the upright's own sides under the bar, and its "1,2 −0,1" runs from the bar's middle to its edge at the square end (read as a slot 1.2 wide until 27 October 2026, drawn 2.0 deep and open at the end). The spring's outer end goes into the sheet's Ø 0.7 hole, drilled along the bar when the spring is fitted, 0.36 from the upright's middle toward the axis (the end view, sure to ±0.05) and 3.15 under the bar (05 03_5, 05 03_1: likely; 05 03_9 gives it no place), 1.35 from the upright's end: 3.55 from the staff, where 05 03_7's curve and the collet's 3.49 pin it, so both curves alike (likely; 0.72 from the end, 3.46 from the staff, until 28 October 2026). Its pin beside it in the hole, outside: half round, the hole's round less the spring's side, its flat 0.005 off the strip, brass, 0.45 proud of each face and domed over its last 0.2 (Ldzmn4kuKMA 4:32-4:34, a GUB's old spring with its stud: a brass end about as wide as the hole, rounded; its length and dome estimated, the face seen obliquely; the video review, 27 October 2026, found no frame that reads its length: both ends proud and rounded, and the GUB's bar hole sunk to Ø 2.2 or more at its top with its outer corner chamfered, that clock's). The drawn curve bows 0.18 across the stud's 1.8, so the drawn spring's last stretch is straightened along the hole; the helix is opened to the hole's height (above); the physics keeps 05 03_7's curve. The drawn spring's straightening is estimated: the maker forms the end to the hole.
- The staff's ends from the later staff 05 03_3.2 (05 04 02 draws only the blank, 14.03 to the lower centre): its upper end 13.0 above the hub's flange and its lower 12.59 below (its 25,6 −0,02 and 12,6 −0,02, each at its middle: 25.59; 13.03 and 25.62, over the overall's limit, until 28 October 2026, 1-M6; 12.83 below until 27 October 2026), each 0.02 off its endstone (the upper jewels following it down 0.03), so the lower endstone's face lies 1.19 inside the lug's face (the coloured section: 1.06 ±0.11); its pivots' cones hollow on R 6 (its detail's "6" read as a radius, likely). The escape arbor's ends likewise, 0.02 off.
- Every jewel, setting and endstone (no sheet): the stones' sizes and form scaled on the coloured section (a pictorial section, to scale where it was checked: likely, ±0.1; above, How the balance and escapement were measured), their holes 0.02 over the pivots (built so since 25 October 2026: until then the balance's 0.04 and the escape wheel's 0.03 over them), the oil gap between hole jewel and endstone 0.03 (at the escape wheel 0.07 above and 0.04 below: its endstones 0.03 off the arbor's ends for the 1958 book's 0.05-0.07 of endshake, the hole jewels left where they were, 25 October 2026; 0.06 and 0.03, the endshake 0.04, until then), settings to their seats, each holding its stone by a lip (the section draws them burnished over it); the escape wheel's upper hole jewel as last revised thinned to 0.4 and its lower to Ø 1.6 × 0.45 to fit what the sheets leave; as first drawn the escape wheel's lower endstone Ø 1.6 in its plug, the form scaled; the 6MX's chaton jewels and its contact's are left plain discs with olive holes (no section or photograph shows their insides); stones Ø 2.0 (1.8 and 1.6 for the escape wheel's) × 0.35, plain discs, and the escape wheel's lower hole jewel 0.2 off its endstone (a floor of its bush between them as first drawn), until 18 October 2026; the escape wheel's lower jewel in a bush in hole 26; the escape wheel's endstones in round gilt settings as Wempe 3955 shows them (the upper's spigot Ø 4.5 through the lip, flush outside, two brass screws from outside with heads Ø 2.6 × 0.3 under the balance's rim; the lower's Ø 4.6 flush in a seat 0.25 deep in the dial face with a boss 0.36 proud round its stone, Ø 2.2, two brass screws' heads Ø 2.6 lapping it: 2_Wempe_3955_A.jpg and 3_Wempe_3955_uZ.jpg on millimetre paper; a stadium cap 9.4 × 3 × 0.6 over the lower and a closed setting under the lip above until 16 October 2026); the cock's endstone seen through its setting, colourless (Wempe 3955's and Kirov 247's: sure; a Wempe's described as diamond, Kirov 247's faceted, drawn domed), its screws brass; the cock's hole jewel under it a ruby as the others, showing pink through the endstone (the user's choice, 18 October 2026; 3955's photograph reads grey there, so it may be colourless: unsure); the other screws' heads Ø 2 × 0.6 and their WN numbers where the coloured section's labels couldn't be matched (the block's two, the escape settings', the detent foot's).
- The discharge stone's end bevelled 0.3 back from its acting corner (the code's DS, makeEsc's BEV, drawn since 15 October 2026): 05 04_1 measured again scales 0.15-0.2 (±0.12, its dashes faint at 24.4 px/mm, the "1°" figures beside the corner); 0.15 would move the swing 0.003° and the escapement's own rate 0.01 s a day, and no contact (only the acting corner reaches the gold spring's tip), so 0.3 is kept until a better copy of the sheet settles it.
- The page's escapement (The page's escapement, above): the balance's beat drawn from makeEsc's pushes with the air's and pivots' loss spread as a viscous one (estimated: its share through the beat; its total is TF's); each contact makeEsc solves exactly drawn 0.01 mm apart, as the layout kept them; the gold spring's bend drawn as a turn about its bending point where makeEsc moves its tip bodily (they agree at its square end, where the stone meets it).
The energy budget (phase 2b): 5
- the mainspring's free curve: the Hamilton's measured spring (KLUwI2UUCMQ 32:18) scaled to the length, its turns ×0.75 (the set fitted with the length to 05 06_20's shape with the coils' friction counted, where the level also closes with the drawn strip: Physics: energy; ×0.6, the frictionless fit, until 26 October 2026); its eye the Hamilton's (2.2-9.4 mm along the strip from its inner end, 5.2 high; cut in the drawn strip since 17 October 2026, the hook's face 0.05 off its end toward the tip; the hook's ramp, 0.475, stands 0.1 into the next coil, which a real spring bends over it and the drawn spiral doesn't); its modulus 207 GPa (200-210); no film between packed coils;
- the level: the solved strip at 0.37 gives 25 % more torque than 05 06_20 measures; the budget and the strengths take the solved shape at the measured level, the losses at their middle (×0.883);
- the losses to the fusee arbor: the spring's own up to what mainsprings measure (ICMFF9, as the Hamilton's), the coils' mu 0.08-0.16, the pivots' and the chain's rivets' mu 0.10-0.15, the fusee arbor's pivots counted or not (05 06_20's rig isn't drawn);
- the meshes' friction, mu 0.10-0.20 (steel leaves on brass teeth, run dry), and the pivots' shake for the holes' tolerance (0.02-0.05, the drawn bush bores; the WN sheets aren't in the set);
- the strengths' ranges (strength.js's: brass, hardened steel, a mainspring's limit), Lewis's Y 0.2, each pivot carrying its arbor's whole load, the chain's plates 0.26 thick (drawn: three plates in its 0.82), its hooks 0.80 (the strip 0.9 finished to the chain's width), the band 0.78 wide, the stop pin's and stop bar's steel (no sheet).
The escapement in time (phase 2a): 9
- the balance's free run-down TF 111 s, a running 6MX's measured on video at the model's own swing (111.1 s, 102-125, at 194.3° since 19 October 2026's physics pass; 108 s, 107.8 s, 96-121, at 199.4° before: References/wempe/VIDEOS.md, "Measured"; a 6MX's balance, not the Wempe's; taken since 15 October 2026, the user's choice), inside its parts' damping (81-208 s: the air's drag coefficients, the endstone's effective friction taken from the Hamilton's measured, the spring's own Q; their middle, 125 s, was taken until then); so the swing, 188.5-199.5° over the wind;
- the train's efficiency 0.780, the geometric mean of 0.730-0.833 from its pivots at published friction coefficients and its meshes worked tooth by tooth (gearing.js --model wempe at mu 0.10-0.20; 0.749 from the meshes' rule of thumb until 19 October 2026);
- (the discharge stone's place on the staff,
DSB, was an estimate here from 16 October 2026, leaving the gold spring's tip 5° after rest with the release at +2.6°, "the scan can't give it", and before that leaving the tip at rest; since 11 November 2026 it is 05 04_1's own figure, the 5°: Readings corrected) - the detent's preload, 0.8 g at the stone (just over the margin's floor with the deeper lock, at the 0.80 g cap above which the stone, landing with brass's restitution, lands on the escaping tooth's back during the impulse (Closed, 25 October 2026; The physics pass; 0.63 g, the Hamilton's after Op. 78, until 19 October 2026: no Wempe source gives one; a banking sets the lock, the 1954 instruction's п. 11), and its restitution on the banking (0.3); the steel detent spring's modulus 205 GPa; the gold spring's, 98 GPa (96-101: Au/Ag/Cu 333-333, the alloy Poljot 20027's passport gives the 6MX's; 05 04 01-2 says only "Goldblech 333": likely; 90 until 19 October 2026); the brass tooth on the sapphire stone mu 0.15;
- the hairspring's modulus 206 GPa (200-210) and its working length as read (Physics: hairspring and temperature): the period 0.468 s against 0.5;
- the densities of the rim's nickel steel (8.1) and the gold spring (11.6, 333-333 as above; 11.0 until 19 October 2026);
- in makeEsc, the discharge stone's bevelled end as a straight bevel from the acting corner to the back corner, 0.3 (scaled), and the gold spring's tip as its strip's square end;
- the maintaining spring's working (wempe_sustaining.js): its end at the wheel's pin held by the recess's wall as clamped (the ring's 32.3 -0.1 in the recess's 32.3 +0.05: no figure says it bears), the modulus 207 GPa (200-210), the detent taking the ratchet half a tooth back on average; so its ends' 0.27-0.58 mm in running and its 11-14 minutes; the twist's swing, about 130°;
- 05 06_20's force scaled off its curve (±0.7 g), by the chain's turn on the groove from the large end: the page's turns from full wind taken off the stop's turn, 8.638 (escphys.js MF; fusee.js MW, the page warning if they part), its run down 8.70 turns on, 0.06 before the curve's start, taking its first value.
The escapement in time (phase 2d): 5
- the stone's friction on the tooth it has let go (μ 0.15, as on the lock: 0.10-0.20 move the landing −9.5° to −9.1° and the swing 214.5-213.5°), its landing on it plastic, and makeEsc's quasi-static ride (
RW); - the detent's own damping (Q 100) and its restitution on its banking (0.3), the Hamilton's;
- the twist's swing, 0.6 of the running swing (128°);
- in the frame (tripping.js --model wempe): the banking a single contact, the pipe's side on the banking screw's head at the stone (05 04 01-4's cross screw and the 6MX's photographs: likely; its head not drawn), its stiffness tripping.js's; the contacts' penalty stiffnesses and restitutions, tripping.js's (the return contact's matters: Physics: in time); the gold spring's tip square and unturning in its contact; the gold spring's fixed part rigid with the square up to its bending point (05 04_1); the screw WN-14's mass weighed, at its centre; the stone's lower half's height (to 0.06 under the teeth);
- the train beyond the escape and seconds arbors in makeEsc's JW left out (0.03 g·mm², −0.08° of swing).
The transmission (16 October 2026), tools/wempe_transmission.js: 8
- each mesh's stiffness, the teeth as cantilevers (the brass wheel's tooth and the steel leaf in series, halved for the contact: 1,620 N/mm a millimetre of face; traindyn.js's), and its damping (3 % of critical, oil);
- the chain's stiffness, 120-700 N/mm (its plates' and rivets' give over the free span and the turns on each drum the tension reaches, μ 0.15 on the groove), 290 taken;
- the click's face on the click wheel's tooth 10 kN/mm, the detent's 5 kN/mm, the escape tooth on the locking stone 2 kN/mm, the stop bar on its pin 6.7 kN/mm (its sizes, wempe_strength.js's), the maintaining spring banked 40 times its running stiffness; the contacts' damping 5 %, the springs' 2 % (the let-go's figures over the ranges each is varied in);
- the pawls' springs' set, 0.3 mm (the clicks') and 0.5 mm (the detent's), and the click wheel's backs a straight rise over a pitch;
- the coils' stick: the friction taken up over 0.05° of the drum;
- the chain's mass, 8.6 g (2.9 mm³ of steel a pitch), the up-and-down wheel and hand's inertia (560 g·mm²) and the key's (2,200), none weighed;
- the hand: its grip 1 N·m a radian, winding at a turn a second in half-turn strokes, a strong hand 1.06 N·m (Swain 1970), easing back over 0.15 s; the key's coil spring's drag slipping, 5 mN·m;
- the cannon pinion's fit, 16.9 mN·m (the middle of its window: no sheet gives it).
The hairspring and temperature (phase 2c): 5
- the reading of 05 03_7's "13 Umgänge −3,5 mm" as the whole strip, and its sheet as this chronometer's (likely: Physics: hairspring and temperature); the strip's ends past the pins (1.35 and 0.9 mm);
- the drawn spring's isochronism (
WESC.SET.HS−0.543 s a day per 10° about 207°) from its curves as drawn, both 05 03_7's table; the strip's own mass and the curves' rise left out; - the rim's nickel steel as Guillaume's 42-44 % ("Sonderlegierung" isn't named further): 7-8.5 × 10⁻⁶ a °C, E 145-160 GPa; brass 18.5-20 × 10⁻⁶, E 95-110; the carbon steel spring's thermoelastic coefficient −240 to −270 × 10⁻⁶ and expansion 11-12.5 × 10⁻⁶ (published ranges, named in the tool);
- the masses clamping the rim over their slot (Ø 6.3) so it doesn't curl under them; the arm rigid; the quarters' roots at the arm's edge;
- the secondary error: the steel spring's share from Dent's error (2-3 s a day over 0-30 °C), and the integral balance's taken as Guillaume's balances' fifth of it at Neuchâtel (1902): the nickel steel's quadratic coefficient isn't to hand.
The dial, motion work and hands (P1e): 12
- the hour wheel's collar, 3.585 over its wheel's lower face, fitted to end 0.3 under the dial with the wheel on the cannon pinion: its sheet (05 02 03, 1940) gives 5.2 −0.1, which with 05 05 03's tube (1943) would put the Ø 8.0 collar 1.4 into the dial's Ø 6 hole; its overall 8.2 kept;
- the seconds hand's height, 0.2 over the 1.2 dial on the 1946 post's finished 7.2 (the coloured section, pictorial); the hour and minute hands are at 05 02_1's boxed 2,6 and 3,2 (above), the minute hand's on the tube's shoulder read as the 3,2 (likely), the hour hand's set by how far it is pressed;
- the pinions' tips and roots (above), the change pinion's leaf thickness 0.55 on the pitch circle, the up-and-down pinion of steel (the coloured section colours it yellow; Wempe 3955's is steel);
- the cannon tube's square's corners turned to Ø 3.45 (Wempe 3955's,
1_Wempe_3955_Z.jpgat 9.14 px/mm: sides 2.60-2.67, half-diagonals 1.72-1.77;3_Wempe_3955_uZ.jpgthe same: likely, ±0.1; Ø 3.2 until 18 October 2026), its crown so starting 0.6 under the top, and its diameter 3.6 (scaled 3.65); the change wheel's collar Ø 5.5 and the up-and-down pipe's Ø 3.4, 7.7 (its flange: Wempe 3955's,3_Wempe_3955_uZ.jpgat 8.45 px/mm, 7.71 ±0.15, likely; 7.4 scaled until 18 October 2026) and 2.8, the hour wheel's collar Ø 8.0 (05 02 03 scales 7.95-8.2, Wempe 3955's 8.01, rms 0.03: likely; 7.9 until 18 October 2026) and bore 3.62 (scaled at 5:1); the up-and-down wheel's hub Ø 10.4 (the sheet's 10.5 −0.2; Wempe 3955's measures 10.77-10.92, recorded, not adopted: the drawn figure's tolerance excludes it, and Wempe 3955's version is claude/wempe-photo-inner's); the pipes' bores Ø 1.52, 0.01 clear of the studs (Ø 1.5, train.js; 05 02 02 and 05 02 04 scale them 1.50-1.56); - the change and hour wheels' riveting sinks (27 October 2026): 040204-1's "0,4" and "30°" at the hour wheel's hole, on its lower face (05 02 03's section draws the chamfer there, the pipe's foot flared into it), the 30° read to the axis (its leader on a chamfer about 0.2 across at 5:1: likely), Ø 6.46 at the face; the change wheel's, drawn the same on 05 02 02 (enlarged 6×, about 0.4-0.5 deep and 0.2 across) but not figured, made the hour wheel's (likely); the up-and-down wheel's the same since 28 October 2026 (05 02 04's "vernietet", its leader on the bore's lower corner, a small flare drawn there; not figured: estimated; until then nothing under it, the second drawing check's 7-M2). Their bores, and the change pinion's and up-and-down wheel's, are polygons on their pipes' lathe angles (48, 64), the pipes lying on their flats exactly (until then 24-gons the pipes stood 0.02-0.03 into)
- the hands' outlines between the sheets' stations (traced), the up-and-down hand's length 10.2 (measured on Wempe 3955's dial: its sheet isn't drawn to scale there) and its pipe Ø 3.0 (scaled), read as a collar drawn up from the hand's 0.6 strip (its side view draws the boss a thin-walled tube under the flange, its walls strokes as the blade's: likely), its blade an even 0.3 under the flange's 0.5 (the side view's one stroke, 0.5 tapering to 0.3 until 28 October 2026: 7-M4), the hour hand's flange bevel (Ø 8.2 to the plan's inner circle 6.8), the minute hand's flange's round (r 0.4, scaled);
- the seconds hand's collet (05 02 01-2, no sheet): Ø 1.5, 4.6 long, scaled on the coloured section, its end Ø 1.2 through the hand;
- the dial's screws (WN-10 by the coloured section's label, likely: M1, heads Ø 1.7 × 0.8) and the ring's tapped holes for them; the dial's stepped pin (Ø 1.1 in the ring, 3.7 deep as the coloured section draws it, Ø 1.0 in the dial, whose hole scales 1.0; the step estimated); the hole at 185.7°; both small holes under the printed face, which no photographed dial shows pierced (Wempe 3955's
1_Wempe_3955_Z.jpgat 9.14 px/mm, where a Ø 1 would be 9 px and the screws' sinks show; Lange 5177's; Kirov No. 247's: sure; through the printing until 18 October 2026); - the dial's printing: traced on one photograph (Wempe 3955's, 9.2 px/mm), so its edges are good to about 0.03 mm and its line widths include the photograph's blur (sigma 0.046 mm) where under it; the 20's 0 and the 8's top, under hands there (above);
- the Lange dial's printing (Lange 5177's, 8.9 px/mm, blur sigma 0.024): the same, and where its rust lies on the printing (wear, left out by its colour: brown where the ink is grey) the glyphs' edges taken a quarter of the way from the ink to the paper (0.016 mm in from half way, under this blur), so a few edges stay rough by 0.05-0.1 mm (the S of SÖHNE, the R and N of DRESDEN, the seconds 20, 40 and 50); estimated outright: the 16's 1, lost under rust, which is the seconds 10's 1 scaled to the up-and-down figures' height (0.695) and set by the 6 as the 10's 1 stands by its 0; the serial's last 7 (its stem broken by rust), the first 7 fitted on what shows; the 8's top under the minute hand, an ellipse through its upper loop (as Wempe's); its divisions under the hands or moved by rust (the seconds' 6) at the nominal angle, and the outer corners of the up-and-down band's ends sharp (not measured); the ground white, not the photograph's aged cream (above);
- the glass's underside 17.0 over the plate's dial face (05 02_1's pencil, unsure), until the case was built (P1f: 16.7, above);
- a fill light from below in the page (app.js), so the dial, which faces down in the page's views, reads white.
The case and box (P1f): 12
- the bowl's machining: the recess Ø 68.2, the winding hole Ø 8.2, the screw's M3; its inner corner r 7 (scaled); its material: brass as the sheet, though the sheet's "Gewicht 350 gr." is a quarter of the 1.34 kg this bowl weighs in brass (158.4 cm³ with its brackets, weighed on the solid, phase 2d: 350 g is 2.2 g/cm³, a filled moulding's or, machined, aluminium's; a bowl that light wouldn't hang on the drawn pivots: Physics: case, gimbals and the trial);
- the movement ring's seat 5.3 over the pivots (the bowl's top face until 24 October 2026; 05 01 against its 11,5 reads 4.6 and 4.75, ±0.5, for the 1940 bowl; 5.3 so the cast bowl's foot clears the ring as it turns to be wound; the ring's top level with it until 21 October 2026, the pivots then 11.5 under it);
- every line of the bezel's section traced on 05 01 01 (no figures, ±0.2); its thread (05 01 01 marks it; its size and pitch: The bowl's thread, rebate and notch, above; until 24 October 2026 its lower bore was opened 0.35 for the ring's pin and plain); the glass's Ø 112 × 2.3 (scaled on the 1941 bezel) and its seat flush with the top; the notch for the ring's pin; the radial pin's 2.0 out and 9.4 long, its hole not cut;
- the gimbal ring's material (brass; Wempe 3955's is Bakelite; its sizes measured on 05 01 since 25 October 2026, How the case and box were measured); its bracket's length, 57, and its screws, 35.5 apart (Wempe 3955's ring,
16_Wempe_3955_Gehäusetopf_Kardan.jpg, 35.5 ±0.8: likely; 37.2 until 18 October 2026); the ring bracket's screws round holes where 05 01 says they slide in slots ("Kloben verstellen"), M2.5; the pivots' shoulders 0.1 off what they bear against (endshake), the tapped holes' fits (the ring bracket's screws tapped through the ring, as Schnitt A-B draws them, since 27 October 2026; 2.75 into it before); the brackets' five screws' length (8 and 7.5, 3.3 into the bowl's wall; 6 until 27 October 2026), their tapped holes in the bowl not cut (bom.py's embed measures their threads in its metal); the outer pivots' heads 3.8 thick (51 00 10's side view, rough; 05 01's elevation 4.1); the knurls of the lock nuts and the bearing discs; the outer pivot's tip at 9 o'clock ending at the ring's inside (05 01 draws it 4.7 long, ±0.5: no longer, so the 1942 bowl clears it turned over); - the case brackets' foot stepped to the 1942 casting's band and body (r 54 over 13.5 under the pivots, 53 under: 05 01's 1940 bowl has no step), the foot's 3.7 thickness carried along its length and its slots not drawn, the boss's sides radial; the WN-78 screws' M4 (their heads Ø 7.0 as DIN 84's M4); the locking bracket's back stepping out under the bowl's band (its face, crank and slot measured on 05 01, 24 October 2026), the transit lock's lever (28 × 8 in plan) and knob (Ø 19.6), brass with its hub and pin on the drawings' brass case as on Wempe No. 6161's (
antiquorum_208-4_wempe6161.jpg, one photograph: likely; black knob on steel until 18 October 2026; the 6MX's black on steel, as Wempe 5377's and 4585's): scaled on 05 01 at 2.45 px/mm, their forms after Kirow 422's bowl and the sheet's small views; its heights, which no sheet draws, read on Wempe 5377 (bonhams_26816_327) and Greenwich's wartime Wempe against the knob's Ø 19.6 (likely, ±1.5): the lever 2.5 thick (at the pivots' height, in the locking bracket's slot: above, the locking bracket and the transit lock), a hub Ø 9.8 standing 10.8 under the knob, the knob 4.5 thick, its top 4.6 over the rim, the pin Ø 4 standing 16.7 over the lever (16 to 24 October 2026 the lever lay at the box's rim over the ring's top, the knob's top 18 over the rim; until 16 October at the pivots' height, the knob 10 thick on a Ø 4 stem); its bracket's form estimated; - the closing plate's screw and knob (WN-71 head Ø 7.2 × 2.5, M3; WN-72 Ø 5.2 × 2.4); its spring (Verschlußfeder 05 01 00-7: Closed, below): the steel wire Ø 1.0, its two turns from r 12.35 to 6.5, the bends r 0.8, the hole Ø 1.2 × 1.5 for its inner end in the bowl's bottom and its stiffness, all estimated; its turn shut, 25° from open (its Ø 8.1 clears the Ø 8.2 hole from 20.8° on; the 6MX's shutter is a pin in a slot, Uy8A88_j-cA 5:21-5:25, so no measure for this one);
- winding in the case: the bowl turned a full 180° (the videos show its bottom facing up; the instruction says "onto its side"), the way the dial goes (toward 3 o'clock: DIxob2Rl4dc 7:07, likely), and 0.8 s for each step (the turn, the plate, the key);
- the pins over the outer pivots (05 01's elevation; How the case and box were measured, The box): their size and place scaled on the sheet's pixel profiles (Ø 2.2-2.9 between the lines' centres and outsides, built 2.5; 2.3 proud of the parting face and 3.3 into the wall, ±0.4; likely), their purpose (a lid-locating pin: inferred), their brass, their foot set in the wood without a bored hole (as the handles' screws), and the closed lid's hole for each, Ø 2.7 × 2.6 (no sheet draws the lid; inferred from the pin standing proud) (25 October 2026)
- the handles' finger recesses' rounding (radius 10, as deep as the hollow: the section's curve fits it at one more point, 2.5 over the foot) and their place along the wall (centred under the strap); the box's floor 12.5, its boards butted, the lid's top a frame 20 wide round a glass 3 thick, the keeper on the front, the handles' screws: as the photographed boxes show them; the hinge one piano hinge 148 long across the back, its leaves 6.5 × 0.6 let into the parting faces and its knuckle Ø 5 in seven lengths (its length measured on Lange 1947's box from above,
drouot_33810142_lange1947_2.jpg, 664 px at 4.48 px/mm by the box's 185; every photographed box has one, Wempe 6161's, 5377's and Greenwich's too: two hinges 40 long until 16 October 2026, which this line then said the photographs show); the lid's stay, a brass bar 91 × 6 × 1.5 with a slot 2.4 wide, pivoted 5 over the parting line and 40 from the back on the lid's left wall and riding on a pin 20 under it and 45 from the back on the box's (Wempe 6161's form,antiquorum_208-4_wempe6161.jpg, on the left as Greenwich's; Lange 1947's on the right), its places fitted to the lid's travel so it clears the back wall at every angle (it leans about 45° open, where 6161's stands nearly upright: its pin and pivot aren't measurable on the photographs); the knurls (the bezel's lowest 2.5 of its Ø 125, 0.4 deep, Wempe 6161 and 5377; the bearing discs' edges, 6161 and Lange 1947; the transit lock's knob, every photographed box; the inner pivots' lock nuts, knurled brass discs Ø 19 × 2.5 inside the ring against its face, Wempe 3955's bowl, where they were hex steel nuts outside it); mahogany, as Wempe No. 6161's round its brass bowl and gimbals (Antiquorum 208-4; its colours sampled on the photograph), where the wartime boxes photographed with Bakelite bowls are oak (Greenwich's, Lange 1947's; the Überkasten's sheet says bleached birch); - the outer box (51 00_5): its cushions' cover (felt-grey) and form between their figured middles (a lens (1 − u²)(1 − v²), 1 at the rim), the ends' and floor's 20 (scaled 23, 21), the rim strip's 5 and 4, the strap's leather 3 and its loose ends (not drawn), the eyes' form (a disc Ø 23, 2 thick, its screw's round head the Ø 8.5 centre), the hook and eye (commercial: a ring Ø 9 of 1.6 wire, a hook of the same), the hinges' leaves 12 × 1, which numbers of its parts list are which; the catch (19) inside the front not drawn, its form unread; the wooden box's latch and keeper press 2-3 mm into the front cushion
- the maker's plate's place on the lid (Greenwich's wartime Wempe), its four pins; the latch (31 October 2026, the owner's choice, built as Lange 5591's:
js/case.js's LT): the plates' 1.2 thickness, the latch plate's top 8 deep let into the front wall and its face 7 high (the knob's centre at its lower edge, as 5591's), the slots' 2.4 along the wall, the hook plate's face 7 and the hook's 2 below the parting line, the screws' heads; the tongue as the bolt behind the latch plate, out of view in a mortise in the front wall (its 45 can't lie inside the 43.9 plate: its arrangement unknown), its pivot screw (M6, in its Ø 6.2) put in from inside the box and its knob (Ø 9 measured, in its M3.5) the plate's; until then the tongue hung on the lid's front over an estimated keeper; its outline's arcs scaled (the round end R 6 about the hole, the narrow end R 7 through the tip at 39, both edges tapering 1°20' to 8: 10-M9, 28 October 2026; one edge tapering and a semicircle r 4 until then); - the key's tube 8.0 under the body's top (scaled on 51 00 11's section, ±0.15; its free length then 33.0, the sheet drawing the tube 48.1 against its own 50.1), the spring's wire 0.6, pitch 0.95 and about 12 coils (scaled), where its end stands round the axis (free on the sheet), the tube end's relief to Ø 4.6, the joint of its body's four solids 0.12 under the drill point's foot (no figure: where they join is the build's, not the part's), the square's 60° sink 1.1 (its tolerance's middle; built 27 October 2026); the pin's length (15.3, scaled on 51 00 11's section); the paddle's colour (black, as the body: no sheet for it); where it lies in the box.
The case, gimbals and the trial (phase 2d): 5
- the densities (as wempe_inertia.py's; the dial and the hands' Goldin brass 8.45), and for comparison only Bakelite 1.37, hard Buna rubber 1.18, aluminium 2.7 (published typical values);
- gimbals.js's: the pivots' damping (0.05 of critical), the stops' wood (1e6 N/m, restitution 0.3), the seas (but for their periods and NORDFORSK's limit), the box's place on the ship; the box turned a quarter as the roll and pitch swapped (small angles, the box on the centreline);
- the balance's pivots' side friction (mu 0.15 on the Ø 0.21 journal) and the beat error's quasi-static offset; the detent's trip threshold from its preload (0.63 g, the Hamilton's after Op. 78) and weight, static;
- the masses' setting by the adjuster to ±0.45° of their compensating place (the rim's graduation read as eight punch marks of a 60-division; the spread the 6MX passports' adjusted C gives, sd 0.060; ±0.25° until 18 October 2026); the regulation at 20 °C ±0.5 s a day (the cards' largest period means, 0.81-1.90, come from C and S with it; ±2.5 would fail a fifth of the trials);
- the scatter and drift (calibrated on the 6MX's eight test cards' E and R: a later Soviet chronometer's, not a Wempe's), the barometer (1 % of the air's density day to day) and the oil (the drive lost 0-10 % a year): the Hamilton's estimates; the air's share of the damping from phase 2a's parts (the middle of its range).
The Soviet 6MX (the Variants' third version, Kirov No. 247; The Soviet 6MX above). Measured on Altmeppen's photographs, each fitted on the sheets' hole table; estimated or chosen where they don't show: 17
- pillar 39's radius, 37.3: its bearing, 190°, is measured to ±0.5° on both faces, its radius reads 36.6-37.3; on r 37 the drawn pillar would stand 0.11 into the drawn seconds wheel's tips, so the radius is the least that clears them by 0.2 (the 6MX's seconds wheel and its pillar's diameter aren't seen);
- the chatons: each filling the bush's hole (4.59 in the plate, 4.3 in the bridge; about Ø 4.1 shows), the stone flush with the face the arbor's shoulder bears on (so the drawings' endshake), Ø 2.2 × 0.6, its hole the pivot's and 0.025, the sink a cone Ø 3.4 to 1.2: the photographs show the settings' faces only;
- the balance staff: the first-drawn one with its brass collar (no 6MX photograph shows the hub), taken because the escapement stands at the first-drawn heights;
- the barrel: the drawings' 1941 three-piece barrel, its cap underneath (Altmeppen, Knirim); the photographs can't tell it from the later drum turned over;
- the detent: 1436's revised (bracketed) sections and lengths at the first-drawn heights (the 6MX's detent is not shorter: X5); Kirov 14100's slotted foot not drawn, as the drawings' foot's holes aren't;
- the detent block: 05 04 01-4's figures, read in first angle (the upright 3.5-6.5 under the plate; Kirov-Poljot 24020's reads 4.3-6.6, Kirov 247's 3.9-6.6); the taper at the upright's root (one photograph); the stud's thread and depth in the block, the near pin's 1.2, the slide's depth, the stop screw's thread and head height; the banking screw centred in the upright, its domed head Ø 3.2 × 1.4;
- the upright's slit (29 October 2026): 0.12 wide (about 0.1 on both photographs, 2 px at 18.3 px/mm), its floor the screw's hole; the slit end extruded 3.5 long.
- the Geneva stripes: their profile is the photograph's light; the faces the photographs don't show (the plates' inner faces) take the same;
- the dial: its screws' and pin's sizes the German dial's; the serial's two strokes under the seconds hand (the 4's upright below its crossbar, the 7's bar 0.4 under the head), drawn straight on from what shows;
- the bowl: its foot below 8.3 under the cone (unseen, run to the drawn floor), its inside (the bore and a cone 3.4 inside the outer one), the rim's top flush with the flange and its notch for the ring's pin; the brackets' plates' and web's thicknesses, the block's depth taken 4.6 with its outer face at the drawings' r 66.5 for the ring's pivot screw, the locking bracket's crank; the closing plate's spring and screw's head height;
- the bezel's inside and its glass (the 6MX case review, 8 November 2026,
6mx-audit/case/README.md): the glass 3.0 thick (the blind reading about 3, doubtful), flush with the lip as Kirow 422's, Kirova 14100's and Poljot 09777's are (likely), its underside where it was, 0.1 over the cannon tube's crown, so the bezel 14.5 high, a plain band 1.5 between the traced bell and the knurl added to reach it (DEC 422 shows a longer band, on a scale set by its collar); the seat and shoulder not seen; the sight cone (10 November 2026) measured, likely ±1: a white cone from r 52.3 under the glass to r 46.0 at the dial, 0.1 over it, on Kirov 14917 (rAw2zmulpk8 0:22) and Poljot 09777 (Uy8A88_j-cA 2:08) with their bezels on, each frame's camera an ellipse on the minute track (its r 45.13 Kirov 247's, so the scale is borrowed); its paint's colour by eye; Kirov DEC 422's bezel has none (its dial screws at r 49.9 show), so the model follows the two; the knurl a diamond (±28° to the axis, 270 round, 0.4 deep: its pitch doubtful); the thread's pitch 1.0 on Kirov 247's rim (likely), its hand not seen (right-hand, estimated); - the brackets (8 November 2026, the same review): their heights read blind on 247's and 2973's bowls (±1-2, 247's taken where the two part by 2-3), their slots' sizes (18 × 5 on the case brackets, 4.5 wide on the locking bracket, square-ended as drawn), the screws' threads (M4) and lengths, the locking bracket's crank (3 thick) and its block's stand-off (8 ±2); the pivots' height kept at 3.0 under the rim (247 reads 0 ±1.7, 2973 2.5 ±1.5);
- the key: its form the key of 1943's, which no 6MX photograph measures; only its colour, brass, is read (two videos);
- the boxes: the walls, the glazed lid's glass and frame, the hinges, the lids opening together; the outer box's height, parting line, walls, felt and straps (its width, notch and catch measured: X5); the lid's tab drawn filling the notch;
- the physics: the 6MX's own escapement, from its bodies weighed on the page's solids (X5); its mainspring the drawings'; the gimbals' periods the drawings' (its bowl, hanging 7.0 lower, weighed apart and run on 7 November 2026: 0.578 and 0.661 s, every check passing; Unresolved);
- the electrical contact: the lever, staff, stone, cock and spiral's places from Romanov's Fig. 100 mapped onto the photographed parts (±1.5), the base's inner edge (±2), the blocks' outlines, the contact wheel's tooth depth and form, the springs' sizes (±15 %), the jewels' sizes and the staff's pivots (each 0.02 off its cap jewel, 0.04 endshake: no photograph shows them inside their settings; the upper ended 0.1 into its stone until 24 October 2026), every screw's thread; which half-second the contact is open; the stud's outer face kept at r 44.0 and the stone's bevel to 0.3, so the lever swings clear.
- the contact's drag on the train (7 November 2026,
6mx-audit/delta.md§4,tools/wempe_6mx_contact.js; the owner's choice: recorded as a range, the page's physics left without it): on every other beat the contact wheel's slope lifts the lever 4.6° up a 58° flank against the spiral 59, its work out of that beat's impulse (36 µJ at the escape wheel). Through the 6MX's makeEsc it costs about −4° of swing at a middle estimate of the contact's force (0.14 gf at the screw: a spiral 0.05 × 0.3, one turn), −1.4° to −30° over hairspring-like spirals of the measured size (0.01-1.4 gf), the rate under 0.25 s a day to 0.2 gf; from about 2 gf a lift beat falls under the least drive. The TU holds the contact and contactless 6MX to the same requirements and trial, which rules out the stiff end. Unknown: spiral 59's section and preload (Romanov 1975, p. 208, calls it a hairspring, волосок; the TU gives only the current, 5 mA), and the screw's travel off the disc (about 1.15 mm from the contact wheel's estimated root, the stone's 0.4 rest and Fig. 100's arms), which the drag scales with; each figure is an upper bound for its force (its arm taken whole).
Left out, small: 1
- Left out, small: the stud's Ø 0.8 round at its point; the balance rim's graduation (05 03 01-1: "8 Körner in 60 Teilung"). The barrel bridge's pin holes' 0.3 × 90° countersinks, the upper cock's pins' 0.2 × 90° sinks (16 October 2026) and the dust bush's bottom, a flat ring 0.5 wide with the face dished 5° to the bore (26 October 2026; a 5° × 0.5 chamfer until then) are in; the dust plate's 0.5 × 45° (05 06 00-1, on the face toward the plates) and the cover plate's outer 45° (05 06 00-4, on its outer face with the sinks; not sized, scaled on the section 0.6-0.7 and drawn 0.65, leaving a 0.15 land: estimated) since 25 October 2026 (fusee.js,
chamf).
3. The escapement
The Wempe's spring detent escapement is laid out on one sheet, 05 04_1 (Hemmung für Feder-Chronometer, 10:1): the escape wheel 10.00 mm from the balance, the locking stone 36.5° on from the line of centres, the impulse 21° either side of it. Its parts come from their own sheets: the escape wheel's tooth (05 04_23), the detent and its gold passing spring (1436, 05 04 01-2), the rollers and the balance.
3.1 Solved from the layout (makeEsc)
Method. The shared escapement solver, makeEsc, takes the layout's points put in its frame, the parts' shapes and bodies (the balance weighed on the
model's solids, the train behind the escape wheel, the detent about its flexure), and solves the escapement as the Hamilton's is solved: the wheel released from rest
chasing the impulse stone, the strike's loss, the unlocking's work, the detent's fall and ride on the tooth it has just let go; then the swing at which the escapement's
work each oscillation balances the balance's damping, at the drive 05 06_20's measured force gives through the train. The rate is Airy's sum of the escapement's
disturbances with the drawn hairspring's own isochronism (section 8).
Since 11 November 2026 the tooth is let go where the layout has it. 05 04_1's "5°" stands on the balance's arc beside its 6° and 22°10': the impulse stone is 5° inside the teeth's path when the tooth is let go. The model had the discharge stone 9.2° earlier on the staff, an estimate. Put where the sheet has it (the owner's choice), the wheel, let go from rest, reaches the impulse stone only about 5° before the line of centres and drives it through little more than half the drawn impulse, and the swing falls from 194° to 161° at 12 h. On the measured drive no damping the balance's parts allow reaches the sources' 225° (section 5), which two checks report and no longer fail. The drive (05 06_20) and the damping (TF 111 s) are kept, the owner's choice; the model's README has the reading (Readings corrected) and what is open (Unresolved).
ampAt). The green band is the sources' 225-270° (the 1954 instruction for chronometers in general); the model's swing lies under it (section 15).
wempe_escapement.js.wempe_escapement.js (rateAt).3.2 In time (dynamics.js)
Method. The balance, the escape wheel with the whole train behind it, and the detent move as bodies through every contact, beat by beat, on contact geometry worked out apart from makeEsc's: the bevelled discharge stone on the gold spring's square end by separating axes, the stone on the tooth it let go from the tooth's drawn arcs. The result is held against makeEsc's: the swing, where the tooth lands, the detent's fall and its home, the rate and its isochronism. Then the detent's estimates are varied, the chronometer is started by a twist, starved of drive, knocked, and taken to sea.
3.3 The detent as a frame (tripping.js)
Method. The detent becomes a plane frame: beam elements with stretching, bending and their consistent mass for the spring (0.07 × 1.9 mm, clamped at its foot), the blade's two sections, the horn and the gold spring along its drawn path; the square with the gold spring's head and the pipe with the stone rigid. Its modes carry it in time with the balance and the wheel through elastic contacts: the discharge stone on the gold spring, the gold spring on the horn, the pipe on its banking (the block's cross screw), the tooth on the stone and on the impulse stone. Validated rigid against dynamics.js, it is then run as drawn, with its estimates varied, pushed to larger swings, and knocked.
tripping.js --model wempe, section 3.4. The mainspring and the fusee
The drawing set has a sheet no other chronometer's drawings are known to have: 05 06_20 (Herb. Müller, 24.7.41), the fusee's curve and its measured force, the pull in grams on a lever 262 mm long over the whole wind. It gives the strip (15 × 0.37) but not its length or free shape.
Method. The Hamilton's mainspring.py solves the strip in the drawn barrel (Ø 38.5 on the arbor's Ø 13.3 core) for its shape of least bending energy at
every quarter turn, coils pressing on each other, its torque the energy's slope. Its free curve is the Hamilton's measured one scaled to the length, its turns scaled by a
set. Set up ¾ turn (the sheet's "3/4 Umgang gespannt") and wound through the drawn fusee and chain, its torque on the fusee arbor at each of the sheet's readings is set
against the measured force, each scaled to its mean. Twelve lengths and sets were solved; the best fit is the model's spring.
wempe_mainspring.py, wempe_mainspring.json.wempe_mainspring.py.The level is the drawing's open figure.
5. The energy budget
Method. Where the drive goes, from the mainspring through the fusee and chain, the train and the escapement to the balance's damping, each loss from the Wempe's own parts: the coils' friction (section 4), the barrel on its journals, the chain's links on their rivets, the fusee arbor's pivots; each mesh tooth by tooth (section 6) and each pivot on its tooth loads; the escapement's strike and unlocking (makeEsc). The balance's damping, which no Wempe source gives, is built from its parts: the air's drag on its masses, timing weights, screws and arm (a pressure drag at the masses' Reynolds number), the endstone's friction under the balance's weight, the spring's own. Then: does some balance within its parts' damping swing the sources' band on the measured drive?
wempe_physics.js.6. The going train, tooth by tooth
Method. The train is four meshes: the fusee wheel (90) on the centre pinion (14), centre wheel 90 on the intermediate pinion 12, intermediate 80 on the seconds
pinion 10, seconds 80 on the escape pinion 10; every count, module, tip and root from the wheels' tables, the two pinions no sheet gives fixed by the drawn centres.
gearing.js takes the page's own outlines, places each pair at its drawn holes, and for 120 steps through a pitch turns the pinion back against its load until
the outlines touch, giving the torque it receives with the teeth's friction (µ 0.10-0.20, steel leaves on brass). The four ratios as their wheels turn drive the balance
through the escapement's equation over six hours. Then each mesh's centres are moved until it jams or its friction takes the swing out of the model's band: the window
the holes must hold.
gearing.js --model wempe.gearing.js, day().gearing_wempe.json.7. The parts' strength
Method. Fully wound, at the measured level of the drive, every stage lossless (the largest forces): the mainspring's bending stress; the chain's plates, rivets and hooks under its pull; the band; each mesh's teeth by Lewis' formula (Y 0.2, clock teeth); the pivots as cantilevers carrying their arbor's whole load; the maintaining spring, ratchet and click wheel; a strong hand on the key against the stop. Each against its material's published range: the margin at its weak and its strong end (~~ where only the strong end holds).
wempe_strength.js.The maintaining spring. Its eye's pin goes up into the ratchet and its other pin down into the fusee wheel (05 06_4's Schnitt A-B: the eye's pin drawn whole,
"Stift nach oben", the other hidden), so the drive closes the open ring until its ends nearly meet, its outer edge leaving the wheel's recess; the end at the wheel's
pin, its short wide tail against the recess's wall, is held as clamped. Its stiffness from its drawn section (the width traced round it on 05 06 01-1), by Castigliano at
small turns and as an elastica as it closes; how far the fusee's drive (05 06_20) closes it and where its ends would meet; its stress; and, the key held, the train run on it, the
swing following, with the maintaining detent catching the ratchet up to a tooth late. wempe_sustaining.js.
8. The hairspring and Phillips' curves
The hairspring is a helix (05 03_6: 0.285 × 0.52, Ø 12.8, left-hand), its ends bent to a curve drawn on 05 03_7 as a table of radii every 10°, and cut, before the curves are bent, "auf 13 Umgänge −3,5 mm": to 13 turns less 3.5 mm.
Method. The length is read four ways and each gives the balance a period. The curve's table is fitted as two compass arcs and tested against Phillips' conditions (1861): its centroid on the perpendicular to the junction's radius, at R²/l from the staff, so that the spring pulls the balance with a pure couple. The force it leaves on the pivots under a couple follows (HSPR.lateral), with the helix's turns varied. At large swings the drawn spring is solved as an inextensible elastica by shooting and again as co-rotational beam elements; the two must agree on the couple's shape, the force and the rate.
HSPR.large on the drawn spring (wempe_hairspring.js, section 4).wempe_hairspring.js, section 3.9. Temperature: the cut bimetallic balance
A steel hairspring weakens as it warms, so the balance must open to compensate: the rim, steel inside and brass outside, cut beside the arm, curls in as it warms and carries its four masses toward the staff. How much depends on where the masses sit on the free arc.
Method. Each quarter of the rim is a bimetal cantilever from the arm's edge to the cut, curling by Timoshenko's bimetal (1925), each element's radius moving by the layers' mean growth, the masses clamping the rim over their slot. Every part is weighed on the model's solids. The spring's own loss is its thermoelastic coefficient's (−240 to −270 × 10⁻⁶) with its expansion. The rim's "Nickelstahl Sonderlegierung" is read as Guillaume's 42-44 % nickel steel (estimated); a plain nickel steel is tried beside it. The secondary error (Dent's, 2 s) against Guillaume's nickel steel as NBS Circular 58 tabulates it, checked against the 6MX passports' S.
wempe_thermal.js.The frame, train and escapement in heat and cold
The plates, pillars, bridges, wheels and, unlike the Hamilton's, the escape wheel (05 04 05-1, Ms 63) are brass; the pinions, arbors and detent steel, the gold spring gold, the impulse roller beryllium copper. Over the TU's working range, 4 to 36 °C, assembled at 20 °C, what isn't brass moves against what is.
Method. Each mesh's depth changes by the pinion's pitch radius times the brass's and steel's difference, against gearing_wempe.json's windows; each
arbor's endshake by its brass gap and steel length (the bench's stacks, wempe_endshake.js), against the 1958 MX repair book's bands. The escapement runs through
makeEsc in the brass wheel's own frame: the steel detent from its brass-held foot (the depth of lock, the gold spring's tip), the rollers on the steel staff, the springs'
moduli and the mainspring's torque by their thermoelastic coefficients; at the published constants' middle and at the corner that moves each part most (brass 20.9,
steel 10.8 × 10⁻⁶ a °C), with the drawn lock and with the bench's, the window's middle. Where makeEsc loses the impulse, dynamics.js --model wempe in time
was run on the same settings and agreed when this was found (27 October 2026: the swing 91-97° then; not run again since the discharge stone was put at 05 04_1's 5°, where makeEsc gives about 80°).
Found. The depths, endshakes, lock and chain hardly notice (under 4 µm). The gold spring's tip does: 1.8-2.3 µm farther from the staff at 36 °C, taking 0.3-0.45°
of the 1.50° let-off, and the escapement loses its impulse at about 1.0-1.1° (the same edge that tops wempe_tolerances.js's lock window). The lock window that holds over the range is about half the one at 20 °C, and since 3.45.00 it is the
window wempe_tolerances.js gives the bench (the owner's choice): 231.7-237.9 µm, the bench aiming just under its top (237.8) so the teeth's wear, which only makes the lock shallower, has three years' room. At the constants' corner no lock holds at 36 °C (open).
10. The case and gimbals
Method. The bowl with the movement in it and the gimbal ring are weighed on the model, every closed solid at its material's density (massprops.py --model
wempe): mass, centre of gravity and inertia about the gimbal centre. 05 01 says to move the case brackets "bis Gleichgewicht erreicht ist", until it hangs level, and
the tool does so. The two bodies then run on their pivots under the Hamilton's seaway (gimbals.js: narrow-band random roll, pitch, yaw and heave; NORDFORSK's
0.12 g limit), and what reaches the balance's staff is run through the Wempe's escapement.
gimbals.js --model wempe, section 2.11. The 6MX's trial and a voyage
The Soviet copy of the Einheits-Chronometer, the 6MX, was made to a published specification (TU 25-07.1533-84) with a trial: 35 days at 36, 20, 4, 20 and 36 °C, the first two days of each period not counted, wound daily, its figures worked as E (the mean variation of the daily rate), R, D, C (the temperature coefficient), S (the secondary error), each period's mean, and N = 42E + 4.5R + 60C + 2.4S. No Wempe test card is to hand, so the trial is the 6MX's.
Method. Each day's rate is summed from its parts: the temperature curve (section 9, with the masses set by the adjuster at their compensating place to ±0.25°), the air's density, the swing over the daily wind, the day-to-day scatter and drift (calibrated on eight 6MX test cards' E and R), the barometer and the oil; the trial is drawn 2,000 times. Then a 60-day voyage from a winter port into the tropics, rated over ten days in port, gives the error a navigator would carry.
wempe_errorbudget.js.12. Building it: tolerances, the bench, the Monte Carlo
The checks above take the Wempe as drawn. A chronometer made to the drawings is made to tolerances, some the sheets give and some they don't, and is then tested and
adjusted on the bench as its makers did. Three tools follow it there, as the Hamilton's tolerances.js, bench.js and montecarlo.js do.
They are guidance for anyone who would make one, proved by their own runs: the model was never made.
12.1 How closely the unsized parts must be made
Method. From the escapement as the page runs it (makeEsc with the Wempe's settings, driven by 05 06_20's force through the train), the swing and rate are solved with the escape wheel's torque and the detent's and gold spring's stiffness each scaled (a strip's stiffness as its thickness cubed). Each part's range is the one that keeps the swing in the model's guard band, 147-270° (its floor 14° under the model's own swing at 12 h; the two builds' 150-270°), over the whole 56-hour wind; the sources' 225-270° is reported beside it. The parts: the mainspring's strip (05 06_20's "15 × 0,37", no tolerance), the detent's spring (1436's faint "0,07") and its preload, the gold spring, the depth of lock (05 04_1's 0.235, set by the banking), and the hairspring against the period, which the timing weights must take up.
The drawn detent's ring, and how the drawn version is judged. The lock's floor and the preload's rest on how far a held tooth's stone rings in the frame (section 3.3). With the discharge stone at the sheet's 5° it rings 126.9 µm, 53.9 % of the depth of lock, under half only from a preload of 0.93 g (116 µm, 49 %, with the stone as it was). By the rule of half the depth the drawn version would have no window: twice the ring, 0.254 mm, lies past the deepest lock that unlocks (0.2436 mm), and the preload that halves the ring past its cap (0.80 g). The owner's choice (12 November 2026): the drawn versions are judged on no tooth getting past, the ring reported; the builds, their gold spring thinned at its bend, keep half the depth. The frame run at shallower locks holds every tooth down to 0.130 mm and lets one past at 0.120: the ring is the gold spring's blow on the return swing, 127-133 µm whatever the depth. The tables below, the bench and the Monte Carlo are worked on that floor (tools/tripping_wempe.json, which tripping.js --model wempe --write writes). Still open: the ring turns on one estimated stiffness, the discharge stone's on the gold spring's tip on the return.
12.2 The tests on the bench
Method. Each test turns the model's figures into what a made part or movement must read, and how to measure it with a maker's means: the mainspring's pull against 05 06_20, the fusee's evenness, the depths, the endshake from the sheets' fits, the balance vibrated, its free run-down, the detent's ring, the escapement's figures and the banking's preload, the swing, the maintaining spring, and the 6MX TU's 35-day trial as the acceptance test (the Wempe's sheets give no trial of their own).
12.3 The whole movement made to tolerances
Method. 2,000 movements, each drawing every tolerance at once (uniform within the sheets' limits where they give them, normal where estimated): the arbors' holes, every term of each arbor's endshake stack from its sheet, the mainspring's strip, the teeth's friction, the detent's and gold spring's strips, the wheel's tips and the banking (the depth of lock), the preload, the hairspring's strip, coil, cut length and modulus. Each is judged as made (the train turns, every arbor free, the escapement unlocks and locks in its window, the swing in the guard band over the wind, it times within the weights' reach), then after the bench's tests as a maker applies them (bench_wempe.json's figures): a close mesh re-bushed, endshake set again, a detent spring out of its band replaced, the banking and preload set, another strip, the set-up turned, the hairspring matched to the balance.
wempe_montecarlo.js, montecarlo_wempe.json.13. The whole transmission in time
Sections 3 to 7 take the movement a mechanism at a time, each with the others held still or rigid. Here every part that moves is one system: the barrel on its solved mainspring, the chain, the fusee with its two clicks, the maintaining ratchet, spring and detent, the fusee wheel and the going train to the escape wheel, the motion work and hands, the up-and-down work, the key and the stop: each a body with its inertia weighed on the model's solids (or estimated, said where), joined by the elements a real movement has, none of them linearised.
Method. wempe_transmission.js. The elements: the mainspring's torque as solved (section 4) with its coils' friction as a stick-slip element,
so winding takes more than running gives; the chain in tension only, so it can go slack, its lever on the fusee where it lies and rising and falling as each 2.05 mm
link comes onto a drum; each pawl (the clicks, the maintaining detent) a body on its pivot under its spring, riding the teeth's backs and catching a face only if it is
down; the maintaining spring's drawn ring, stiffening as it closes, with its bank; every mesh tooth by tooth on the page's own outlines (section 6's), the driven gear's
place under load through each pitch, the backlash to its back flank and the teeth's friction, contact on either flank or neither; the cannon pinion's friction fit,
which slips past its torque; the key's one-way coil spring (it grips whenever the hand holds the key against the fusee, and slips only if the key is turned the wrong
way); the stop bar on its pin. The escapement is dynamics.js's own (section 3.2), its escape wheel driven each step by the train through the escape pinion's
mesh, at its own place and speed. The beat runs from 8 starts of the train's meshes, and each mesh's peak is judged on the worst of them, a figure that holds as the
step is refined (wempe_transmission_converge.js: the seconds wheel's, the escape pinion's take-up after the escape wheel lands on its stone, within 2 %
from a quarter of the step to an eighth). It is stepped in time at a microsecond. The stiffnesses no sheet gives (the teeth's give, the chain's, the clicks' faces, the bank) are estimated from the parts,
and those the results rest on are varied.
Watch the run: the movement in plan, every part coloured by the load it carries against its running load and its deviations from rigid motion magnified, as a finite-element post-processor shows a deformed shape; a beat, the key let go outright and eased back, and the stop, played in slow motion with their time histories (wempe_transmission_trace.js).
wempe_transmission.js.Every moving part in 3D
The runs above give the forces between the parts; here each moving part's own stress under them. motion3d.py takes the page's solids and moves each part as
the page's own update() moves it; motion3d_fe.py solves each part as finite elements (voxel bricks on its solid, a modulus by its material, finer
windows at its contacts, the root's bending kept apart from the contact's pressure) at its worst load in the four runs, held where it is held; the springs (the mainspring
by its solved curvature, the hairspring, the maintaining spring, the gold spring) from their large-deflection solutions. Each part is read against its drawn material:
the 1950s build beside the drawing's.
Open the 3D viewer: every moving part in 3D through the four runs, coloured by the load it carries against its load in running (the plan above in 3D, with its moments and its probe of every joint's force), by its stress, its stress against its material's limit or its speed, the deviations magnified, with each part's load, margin and motion, the kinematics against the tooth counts, and the assumptions.
Every part past its limit but the mainspring (its inner coils, fully wound: section 17's builds and wempe_build.js take it up) is past it only with the key let go outright. Those peaks lie at the contacts, and the methodology's contact study finds them the contact's own pressure: it halves as the load is spread twice as wide, so a real blow dents the click's nose and the tooth's face where they meet. By the beam formulas only the maintaining ratchet's teeth bend past brass (about 500 MPa at the blow); the click wheel's tooth carries about 200 MPa in the contact study (240-280 until 26 October 2026), inside it. The let-go study (wempe_letgo_fix.js) runs that let-go (the worst place, the nearer
click 97 % of the way to the next; and eased back beside it) with the fixes a maker could make: more clicks, evenly spaced over a tooth, so the fusee runs a shorter way
free; a brake, friction between the click wheel and the maintaining ratchet, which the clicks hold still running (so it costs the train nothing) but which the key works
against winding; the click's face cushioned. The stresses are the 3D results' scaled to each case's force; the click wheel's tooth by wempe_strength.js's beam, the highest of three readings (the FE on the tooth gives 0.49 MPa a newton (0.60 until 26 October 2026), wempe_ratchets.js 1.16, the beam 2.05: the methodology's cross-checks).
14. Against a period text
The drawings decide the Wempe; a period text says how a detent escapement was usually proportioned, and so where the Wempe's makers chose otherwise.
keystone.js --model wempe measures the escapement against Watch and Clock Escapements (The Keystone, 1904), Ch. III: the wheel and roller, the
balance planted where the rims cross over a pitch, the impulse and unlocking arcs, the locking stone, the tooth's face and back, the detent and its spring, the balance.
The text is generic, so the tool reports and never judges; where the two differ, the drawing and its sheet are named.
15. The swing measured on video
No Wempe source gives the balance's damping, the figure the swing rests on most. A running 6MX, whose balance is of the same kind (a cut bimetallic rim, four masses, two nuts on the arm), is filmed from above at 30 frames a second in moMvyx8eXfo, 17:53-19:50 (another person's video: linked at the moment used, no frame copied here).
Method. wempe_swing.py reads the balance's arm in every frame as a drop in saturation along the rim's ellipse, folded every 180°, and fits each
4-second window with a sine: the swing, its alias settled by the frames between the turning points. The movement is set down at 17:52 and the swing rises; it is
turned in the hands at 18:46 (the 6MX's start) and the swing falls back. wempe_startup.js fits all the stretches together with the Wempe's averaged balance
equation, d(A²)/dt = 2 Wn(s, A)/T − 2A²·damping/TF, the escapement's work Wn from makeEsc with the Wempe's settings, the drive and each stretch's start free: rising
and falling toward one swing, they fix TF, the free run-down.
wempe_swing.json,
wempe_startup.json.The clicks of two more running chronometers were read with this escapement in time: a Lange VEB (gnIP3NqNbEU,
0:03-1:03) and a Kirova under a dome (KxInG08LWXg, 0:00-0:34). Their pairings leave the swing between readings 80-120° apart,
since which click is which isn't settled, so no swing is read from them (References/wempe/VIDEOS.md, "Measured").
16. The Soviet 6MX
The page's third version (Variants, Version) is the 6MX the 1st Moscow Watch Factory made from these drawings, built as one photographed chronometer is made:
Kirov No. 247 of February 1952, from Johannes Altmeppen's photographs, with videos of other 6MXs where his don't show a part. Each difference from the drawings is
measured on a photograph, fitted on the sheets' hole table, or marked estimated; the drawings' two versions are left as they were (every view the same to the pixel).
The section below is the model's README as it stands: how each difference was read, and how sure. The page keeps the drawings' swing and rate in every version; what
the 6MX's differences would change is worked out apart (wempe_6mx.js, below).
How each difference was read (the README's "The Soviet 6MX")
Status (18 October 2026): complete. X0-X4 (16 October 2026) built the switch, the movement, the dial and finish, the case and boxes, the cards, the essay's paragraphs, the report's section and the physics worked apart; X5 (18 October 2026, below) settled what they left: every one of the 6MX gallery's photographs read for the model, the parts measured on them built (the escapement's collet and detent block, the lower cock, the ring's screws, the bowl, brackets, closing plate and outer box), its electrical contact built, and the page running the 6MX's own escapement. What no source shows stays in "Estimated" (The Soviet 6MX) and "Unresolved"; the asks for the photographs that would settle it in REQUESTS.md.
The Variants' third version, Soviet 6MX (Kirov No. 247, 1952; rev=6mx in the link): the 6MX (6МХ) the 1st Moscow Watch Factory made from these drawings after 1946-47, built as one photographed chronometer is made, as Wempe 3955 stands for the first-drawn sheets. Kirov No. 247 (February 1952, first generation) has Altmeppen's full set (photos/dg-chrono-6mx/: its dial, top plate on millimetre paper, dial side, four obliques, detent and box) and his arrowed comparisons with a Wempe. Its electrical contact (E-Kontakt) is left out. The plan is PLAN-wempe-6mx.md at the root.
X0, the switch (16 October 2026). The version control (heading "Version") has three buttons. userData.rev now lists the versions a group shows in ('last 6mx': the revised sheets' pieces the 6MX kept; 'first'; '6mx' for its own), setRev(v) shows a group if its list holds v, and each onRev callback gets the version's name. Until its own parts are built, the 6MX shows every revised piece: its views are pixel for pixel the last-revised ones (views.py --model wempe --eval "__mv.userData.setRev('6mx')"). Both earlier versions rendered unchanged, every view 0 px. The tools: audit.py --rev 6mx (its keys movement.6mx, box.6mx), ci.py's wempe-audit-6mx and wempe-exploded-6mx; bom.py's dev entries take a list of versions in rev; app.js's cards per version in REVC.
How Kirov No. 247 is measured. Its top plate (2_Kirow_247_A.jpg, square-on) is put on the sheets' hole table by a similarity on four arbors seen on it (the fusee's square in the cork ring, the barrel's square, the balance's cap jewel, the escape wheel's endstone) and pillars 11 and 49: 8.98 px/mm, every residual under 0.55 mm; holemap.py --model wempe lays it over the model's plan hole by hole (it now takes --model). Its dial side (3_Kirow_247_uZ.jpg) the same way on seven holes (the centre, seconds, change wheel, intermediate, escape and the intermediate bridge's two screws): 8.63 px/mm, under 0.42. The millimetre paper under the top plate gives the paper's scale (8.8 px/mm), not the plate's, which stands well above it. Screws' centres are circles fitted to their edges.
X1a, the frame (16 October 2026). Each piece and how sure:
- Pillar 39 at 190° (Altmeppen's list: pillar 39 in another place). No pillar or screw at its drawn 210° on either face; its screw at 190.0° (top) and 189.6° (dial side), where 11 and 49 read 94.9/94.8° and 350.1/349.9°, their drawn bearings: sure to ±0.5°, pillar 49's 350° mirrored across the O-W line. Its radius reads 36.6-37.3 (each reading corrected by 11's and 49's in the same fit). On r 37 the drawn pillar (Ø 8.1) would stand 0.11 into the drawn seconds wheel's tips (Ø 21.9); it clears them from r 37.2, so it is drawn at r 37.3, 0.2 clear (likely; the 6MX's seconds wheel isn't seen). Both plates' holes and seats, the pillar and its two screws move with it (
WD.P39_6MX).
- No hole 20 in the upper cock (Altmeppen: no window in the upper cock; his comparison's arrow points at the Wempe's hole there). Kirov 247's cock is plain where the overlay puts it: sure.
- No hole 53 in the top plate (Stift f. Wendelfeder, for the balance holding work): Kirov 247's plate is bare there, in plain view: likely. Holes 51 and 52 lie under its balance, unseen, and are kept.
- Holes 3, 12 and 40 kept. Hole 3 is a clean Ø 3.6 hole at 0.3° (its Ø 3.5 at 0°), 12 at 105.0° (105°), 40 partly under the barrel bridge at 224°: so Altmeppen's "three small windows by the pillar screws" are not these Hilfslöcher, as frame.js had read them (unresolved: what he meant isn't found on Kirov 247's photographs).
- Jewels in chatons at the intermediate arbor's two pivots and the seconds arbor's upper (Altmeppen; the TU's 15 jewels are the drawings' 12 and these three). Flush gilt settings about Ø 4.1 on both faces of Kirov 247, the pivot in the middle, no screws. Each chaton fills the bush's hole (4.59 in the plate, 4.3 in the bridge), its stone flush with the face the arbor's shoulder bears on, so the endshake stays the drawings' (likely); the stone Ø 2.2 × 0.6 and the sink estimated.
bom.json's six lines carry"rev":"6mx"(a line withrevcounts only in those versions), the bushes"last first", and the arbors'inrelations take either (WN-300.t38|6MX.jw38u);checks.py'sJEWELSis per version (15 for the 6MX).
- The electrical contact's fixings (X5, below): the top plate's two Ø 3.5 access holes over the contact's base screws (219.0° r 37.5 and 179.8° r 38.72, the latter re-read blind on Kirov 247's and 1564's plans on 7 November 2026, 179.1° r 38.6 until then: the README read the 219° one, with the screw's dark slotted head 19 mm down in it, as "a cheese-head screw in the top plate at S 28.75 W 23.07"; Kirov 1564's, without the contact, are open to the pillar plate); the dial side's two flush screw ends at 180° r 38.2 and 220° r 37.9 (M1.7, open on Kirov 1564). The small hole read at S 20.6 O 30.2 is the detent block's near steady pin's hole, read 1.4 off (7 November 2026, the 6MX audit: (-29.98, 21.88) on Kirov 247's and 1564's plans; a brass pin end on 247, open on 1564). The pin is built 0.33 from that, at (-30.0, 21.55): the read place would put its hole through the block's end face (Unresolved).
X1b, the escapement (16 October 2026). The 6MX has the escapement at the heights the sheets first drew, with the revised block's form:
- The escape wheel just under the top plate, on a long cone collet (likely). Kirov 247's detent view (
8_Kirow_247_F.jpg) and Kirov-Poljot 24020's (9_KirPol_24020_Feder2.jpg) show it so, as Wempe 3955's (10_Wempe_3955_Feder_plus.jpg, the first-drawn version's source); Altmeppen's comparison of Wempe 3955 with a 6MX (1_3_Vergleich_Wempe-6MX_Feder.jpg) marks the block, not the wheel. On 24020's, scaled by the block's base (6.5 deep, 26.6 px/mm), the wheel's teeth read 0.35-2.3 under the plate. So the 6MX takes the first-drawn balance, rollers, escape wheel and arbor and their jewels ('first 6mx'), and their Exploded offsets. The staff's form (the 1941 collar or the 1946 hub) isn't seen on any 6MX photograph: the first-drawn one, the staff the sheets draw at these heights, is built (estimated).
- The detent at the first-drawn heights its block holds it at (the foot 1.3-3.3 under the plate), with 1436's revised (bracketed) sections (likely). It is not shorter than 1436's: the 6.4 from the pipe to the square read on the loose 6MX block until 18 October 2026 divided a foreshortened span by the scale across the block; along the detent (24.5 px/mm) it reads 8.2 (7.8-8.6), the drawn 8.4 (X5).
- The block, 05 04 01-4 read in first angle, as the sheet itself reads (DIN's; How the balance and escapement were measured): the upright at the free face, 3.5-6.5 under the plate; on 24020's it reads 4.1-7.0, the detent's blade 2.9-4.1 above it (±0.3 with the camera): sure in kind, the sheet's figures kept. The 6MX settles, for itself, the reading the drawings leave unresolved: its block hangs its upright below the detent, at the first-drawn heights. Its foot a taper (below); the hole Ø 1.3 drilled from the plate's face to the foot's M1.
- The banking: the cross screw through the upright, centred, its domed brass head Ø 3.4 × 1.4 (Ø 3.2 until 29 October 2026: below) on the wheel's side of the pipe, which rests on its flat face (24020's: Ø 3.2 against the upright's 3; the loose block's,
8_Gangfeder_mit_Kloben_Rus_einfach.jpg, reads Ø 3.8 by the upright's 3.0 at 26 px/mm, which would stand 0.13 into the gold spring's path as it bends aside: the mounted reading taken, likely), its thread 0.6 out behind the upright.
- Not built: the adjusting slide. The loose block has a gilt slide in a notch across the base's plate face under a slotted cylinder, and a large slotted screw (head about Ø 3.4 on 24020's, 2.9 under the plate) in the base's end beside the detent's foot; how they meet the plate's hole 13 and which way the slide moves aren't seen (Unresolved). Nor is the collet's form: both 6MXs show one long gilt cone, about 5 long, as Wempe 3955 (Unresolved, below); the first-drawn arbor's cone and pipe are built.
X1c, the barrel (16 October 2026). The barrel cap underneath (Altmeppen's list; Knirim's, against Lange's Kal. 100): the drawings' own barrel, the 1941 three-piece barrel the first-drawn version builds (0207, 020701; its arbor's core and the mainspring 0.44 lower with it): likely. Kirov 247's side views (4_, 6_Kirow_247_N, S) show a drum about Ø 41.5 × 18 under the chain, too fine to tell that ring from the later drum turned over. The maintaining spring stays the revised one. Not built: the lower balance cock's other shape (Unresolved). Since 28 October 2026 the drawings' 1941 barrel is read with its lid on the bridge's side and its bottom on the pillar plate's (drawing check 2, 4-M1): the 6MX is built with that barrel, and which side the 6MX's own cap is on (Altmeppen's "underneath") isn't modelled apart: its discs are the same sizes either way.
X2, the dial (16 October 2026). Kirov No. 247's dial (dg-chrono-6mx/1_Kirow_247_Z.jpg), traced as the two German dials are (dialtrace.py --dial kirov, into js/dialface_kirov.js, WDIALFACE_KIROV; the Variants' dial switch, 1st Moscow Watch Factory, which choosing the 6MX selects):
- Its layout is the drawings': the six printed circles fitted by one homography to 10-25 µm, the sub-dials' centres on the arbors at (0, ±23), measure Ø 89.96, 84.91 (the minute track's lines), 26.18 (the up-and-down circle), 37.13, 33.01 (the seconds track's), 22.79 (the seconds' inner circle), the sheet's 90, 85, 26, 37, 33, 23. Printed thin, as Lange 5177's (blur sigma 0.031 mm), its up-and-down sub-dial laid out as Lange's: the circle open at the top (338.3-22.6 deg) for СПУСК (run down) and ЗАВОД (wound) along it, the band's end strokes at 0 and 56 running in to r 5.33. Every figure of the geometric printing is
dial.js'sKIROV, from--dial kirov --geo.
- Traced: the hours, the up-and-down figures 0-56, СПУСК and ЗАВОД, the seconds figures, the factory's mark 1МЧЗ and ИМЕНИ КИРОВА across the centre, and the serial 247, written in red ink: traced from red alone (red over the other channels, each stroke half way to its own core: the pen's strokes 0.40-0.45 wide, the 2's lighter), drawn #ff617f (the photograph's 165, 59, 79 on its paper's 149, 146, 145, scaled to the model's paper). Where the hands cover the printing: ИМЕНИ's last И (its lower corner under the minute hand) is its first, the same glyph; under the seconds hand's head and stem, the 4's upright (it shows at x 1.59 from its top, z 16.85, to the crossbar) is drawn on down to the line's foot (z 19.25) and the 7's bar (it shows at z 15.46 from x 3.95 to its corner) on 0.4 under the head, straight pen strokes 0.42 wide (estimated; until 16 October 2026 they were lost and the serial read 241); the brass hands' boss and their shadows are cut from the ink, not filled in.
- Its screws at the 19, 39 and 59 minute marks (Altmeppen's list): 112.5, 233.6 and 353.1 deg on the photograph (±1 for its tilt), drawn at 114, 234 and 354, the German dial's 120 and 240 moved; the movement ring's tapped holes for them move with them (both built per version).
X2, the finish (16 October 2026). Geneva stripes on the plates, cocks and bridges (Kirov 247's, 1952; the Wempe's are hammered, drawn plain gilt): straight, 3.95 mm apart (an FFT on plain patches of its top plate, 3.73-4.28 at 8.98 px/mm, and its dial side, 3.71-4.35 at 8.63: the median), running at 50 deg in each face's own photograph (49.8-50.3 and 48.5-52.1): in plan along (-0.643, 0.766) over the top plate, cocks and barrel bridge as one sweep (its stripes run on across them), and along (0.643, 0.766) over the pillar plate's dial face and the intermediate bridge (each plate striped from its own face). Across a stripe the photograph's brightness, folded on the pitch over two patches and averaged (each to its brightest), falls slowly from 1 to 0.61 and rises quickly back: the gilt material's map (frame.js's G6), on solidGeo's plan UVs. Likely: the profile is the photograph's light; the faces it doesn't show (the plates' inner faces) take the same. Altmeppen's "the finish changed in the late 1950s" is later than Kirov 247, which is already striped. The barrel and intermediate bridges are built per version for it, their pins with them.
X3a, the bowl and bezel (16 October 2026). The 6MX's bowl isn't R-05 01 00-1 outside: no Ø 118 flange, but a threaded rim Ø 110.5 for a knurled bezel screwed onto it (Altmeppen's "the bowl and bezel brass", and Kirow 422's knurled bezel). Inside it is the drawings' (the bore, its round, the bottom, the recess and closing plate, the winding hole's seat): the movement is the drawings' and stands in it as drawn. Each reading and how sure:
- The rim, Ø 110.5 (sure to ±1.2): on Kirov 247's dial photograph (
1_Kirow_247_Z.jpg, in its bowl with the bezel off), scaled bydialtrace.py's own fit of its printed circles (8.75 px/mm, 0.01-0.03 mm rms), 24 rays round the dial read the dial's edge at r 51.0-51.2, the movement ring's gold flange to r 53.0 (its 105.95) and the bowl's dark rim outside it to r 55.0-55.6. The rim stands a little under the dial's plane, so ±0.6 for the camera. Kirov 009, 1564, 2973, 22823, 23239 and Poljot 00127's dial photographs, all in their bowls, show the same narrow rim round the flange (by eye).
- The outside profile (likely in shape, its heights estimated): Kirow 422's bowl turned over (
dg-chrono-dec/11_Kirow_DEC_422_Gehäuse.jpg, side on), its silhouette traced every 4 rows and scaled by its band (930 px) as that Ø 110.5 (8.42 px/mm). Body r 51.8 (51.6-52.2: smaller down the photograph, which lies farther from the camera), a cone to the foot, the foot read r 37.5 and taken as the drawn 36.25 (the camera, about 0.33 m off, makes the foot about 4 % larger than the band; the cone's radii are scaled down the same way, 0.962 at the foot to 0.987 at the body), a step and round out to the band (rows 448-472), the band up to the bezel's edge. The heights come from the photograph's rows, put on the movement's frame by two ends: the foot's face at the drawn YB − 65 (the floor where the cork ring's seat needs it) and the bezel's glass 0.65 over the hands. That is 0.1322 mm a row, 6.4 % more than the photograph's own vertical scale (8.05 px/mm at its widths and a 15° view). The close camera leaves that stretch unmeasured: the view tilts from 9° at the foot to over 20° at the bezel. So, from YB: the foot −65 to −62.4, the cone to −51.3, the body to −13.2, the round to the band by −10.0, the band to the bezel's edge at +0.55.
- The threaded rim round the flange (likely): Kirov 14917 with its bezel off (rAw2zmulpk8 0:29 and 2:52, 1080p) shows the thread running up to the gold flange round the dial, and its loose bezel threaded inside. Drawn flush with the flange's top (YB + 4.7), its counterbore r 53.05 down to the drawn seat at YB. A notch 1.8 wide at 12 o'clock takes the ring's radial pin (WN-202, its end at r 55.0), down to YB + 0.8, through the thin wall under the bezel (estimated). The thread isn't drawn.
- The bezel (likely in shape): traced on the same photograph. Its lower edge r 56.1 swells (a bell) to the knurl's tips, r 58.3 (Ø 116.6). The knurl runs over 42 rows, 5.5 mm by the stretch; it is diamond on the photographs, drawn as 360 straight teeth 0.4 deep. Then a plain lip rounds into the top face at YB + 13.5. The glass is thick and stands proud (
12_Kirow_DEC_422_Kasten_1.jpg: a green edge over a narrow brass top): Ø 107 × 4.0, its top edge chamfered 0.8, its underside YB + 12.0, 0.65 over the hands' highest point (the minute hand's boss, 17.70 in the movement's frame), its top YB + 16.0, where the drawn bezel's top is. Inside (estimated: no photograph shows it): the glass's seat 1.5 deep, the sight bore r 52.1 over the dial's edge (51.8), and the shoulder at the rim's top bearing on the flange and the rim, which holds the movement down as the drawn bezel's recess does.
- The brackets: the drawn case brackets and locking bracket, their plates on the 6MX's narrower body (r 51.8). Kirov 14917's inner pivots (rAw2zmulpk8 0:29: the cone-pointed screw in the gimbal ring's middle, below the bowl's rim) work out about 15 mm under the dial's face (YB − 10 ± 3, the frame tilted 53° by the dial's ellipse), the drawn YB − 11.5. Kirow 422's brackets stand higher (Unresolved).
- The winding hole's shutter: Kirov 14917's foot (rAw2zmulpk8 0:12 and 0:36, the bowl turned over) has the turning closing plate in its recess, its centre screw and its round hole away from the winding hole: the drawings' (05 01 00-2), kept. The pin in a slot on Uy8A88_j-cA (5:21-5:25) is a later Polet's, not built.
X3b, the boxes (16 October 2026). Kirov No. 247's box and outer box (dg-chrono-6mx-gallery/leben-des-6mx/13_, 14_Kirow_247_Kasten_*.jpg), built in the drawings' box's place (the gimbals, pivots and transit lock as drawn):
- The box, 190 each way (the TU's "190x190x190", 1984: the only figure; sure for the later 6MX, likely for 1952): orange lacquered wood (Kirov 247's sampled #dc6914 to #e07c3e, drawn at 0.7 of it as the mahogany is), in three tiers, as Kirov 1564's, 2973's, 22823's and 23239's (Kirov 422's and 479's, German movements finished in Moscow, have one glazed lid). The tiers measured on Kirov 22823's box, nearly square-on (
bilder-zum-6mx/10_Kirow_22823_Kasten.jpg), as parts of its height at both edges: the body 97 (0.506, 0.514), the glazed lid 68 (0.354, 0.360), the top lid 25 (0.140, 0.127): likely. Kirov 247's own front puts its parting lines 72 apart by the hasp's width.
- Its fittings (likely, by Kirov 247's front,
14_, scaled by the hasp, 53 wide: 22823's 215 of 773 px): two hasps with knurled screws (the head Ø 11 × 5 on the lower leaf, 6.4 under the line), across both parting lines; the factory's diamond badge on the glazed lid, 38.6 × 24, its centre 37.6 under the upper line, lettered "1 МЧЗ им. Кирова"; the number plate on the body, Ø 31, 40 under the lower line, "247"; brass strips 27 × 12 round each vertical corner at the bottom, 27 under the lower line, 25 under the upper and capping the top (22823's); a ring handle on each side (22823's).
- Estimated: the walls 10; the glass in the glazed lid's top under a frame; both lids hinged at the back, opened together (the page has one lid;
WCASE'srev(v)gives the page the version's lids); the bottom 93.5 under the pivots as drawn, the pivots 2.5 longer for the wider walls, the transit lock's bracket reaching the right wall, the key's shelf with legs 65 so its front edge and the key stand where the drawings' do.
- The outer box (estimated in size): of the same wood, felt-lined, a half-round notch in the body's front at the parting line into which a half-round tab on the lid's front closes, a turning hook on the tab over a brass catch under the notch, the number plate 247 on the lid, a leather strap on each side (Kirov 247's,
13_; Poljot 08479's,14_Poljot_08479_Kasten_komplett.jpg). No photograph scales it: 250 each way and high round the box (felt 18 under and over, 8 at the sides, walls 12), the parting line at half, the notch r 48 (13_: 0.38 of the front's width). The red cloth bag it stands in (the TU's "чехол") isn't drawn.
X4, the 6MX's physics (16 October 2026). tools/wempe_6mx.js (with wempe_inertia.py --rev 6mx, which weighs its escapement's bodies on the page's solids in that version) works out what its differences change; the page keeps the drawings' swing and rate (the user's choice):
- The jewels in chatons change nothing the energy budget can see: the model's sources give oiled steel in ruby and in brass the same friction (μ 0.10-0.15,
physics.js), so the train's efficiency is the drawings'. They tighten the pivots' shake (the jewel holes the pivot's and 0.025, estimated; the drawn bushes 0.035 and 0.05 loose), and so loosen the holes' tolerance a CNC must hold: ±82 µm against ±77 at the centre-intermediate mesh, ±60 against ±47 at the intermediate-seconds, ±35 against ±25 at the seconds-escape (the escape jewels' own shake 0.03).
- The first-drawn balance staff and collar (no hub screws): the balance's inertia 0.01 % less, a beat shorter by about 24 µs, 4.2 s a day fast before timing (4.4 until the bodies were weighed again for 3.06.02), which the timing weights take out as they do the drawings' balance's. The detent's inertia 2.6 % less and the escape arbor's 0.1 %: the swing (191.9-202.0° over the wind, since 16 October 2026's reading of 05 04_1's angles) and the escapement's rate against 12 h are the drawings' to 0.1° and 0.01 s a day.
X5, completing it (18 October 2026). Every photograph in the 6MX gallery (dg-chrono-6mx-gallery/, thirteen more 6MXs), Kirov 14100's parts laid out (chasy-ru-9985-kirova-14100/) and Romanov's Proektirovanie priborov vremeni (1975, Figs. 95-101 and their parts lists) read for the model, each part then measured as below (the 1950s Kirovs first, Kirov 247 before the rest; the user's choice, 17 October 2026). Each reading and how sure:
- The escape wheel's collet: one straight cone with a square shoulder onto the arbor, no pipe: Ø 2.77 at the wheel to 1.70 at its end (1.55 since 29 October 2026: below), 5.08 long on
8_Kirow_247_F.jpg(18.3 px/mm by the wheel's Ø 14 tips and the pinion's Ø 2.97), 3.14 to 1.58 over 5.23 on Kirov-Poljot 24020's (26.4 px/mm): likely. Kirov 247's built; the first-drawn version keeps 05 04_7.1's cone and pipe.
- The detent block's fixing: not through hole 13 but by a slotted steel stud Ø 3.4 flush in the top plate's outer face, 2.2 S of it, between two steady pins 10.0 apart (
holemap.py --model wempeon2_Kirow_247_A.jpg, six seeds, 8.993 px/mm, every residual under 0.57;2_Kirow_009_A.jpgby hand; each corrected by hole 12's 0.4 offset; the two agree to 0.3: sure to ±0.4). In the block's frame its pins stand 1.9 nearer its end than 05 04 01-4 puts them, the stud 2.1 nearer and 0.8 across from hole 13; the block itself stays where the escapement needs it (its holes drilled otherwise: Unresolved). The plate's holes per version (WESC.HOLES.block6). The near pin, 0.55 inside the end face, goes 1.2 into the block, clear above the detent foot's pins (estimated).
- The adjusting slide and the stop screw (on the loose block,
8_Gangfeder_mit_Kloben_Rus_einfach.jpg, 30.3 px/mm across, 24.5 along, tilted 30-36°): a gilt key 3.2 wide, flush in a notch across the corner of the base's plate face and free side, from the stud to the edge and 2.5 down the side, the stud through it; a large slotted screw in the base's free side 0.9 from its end and 3.3 deep, its head Ø 4.0-4.4 over the end face by 1.2, beside the detent's foot (every 6MX Feder photograph shows it): likely in kind. Kirov 14100's loose detent has a slotted foot, so the screw is most likely a stop for the foot's place along the block, the banking setting the lock; how the slide works isn't seen (Unresolved).
- The block's upright: slit since 29 October 2026 (below); until then no slit (the loose block's upright, its face toward the plate, is plain to its end with the banking screw's thread straight through it: likely), and a short taper at its root, widening 0.46 over its last 0.9 (about 27°, on that photograph only: estimate), where the model drew r 2 (estimated). The banking screw's head Ø 3.2 × 1.4 was taken to fit all three readings (3.3 loose, 3.1-3.4 on 247, 3.4 on 24020; the loose block's 3.8 came from the wrong scale).
- The lower balance cock: full depth only over its lug, the rest of the bar toward the screw and pins cut back to 3.3 deep (every 6MX side view of the detent, a stamped number on the deep part; on
8_Kirow_247_F.jpg, the full depth taken as the drawn 10: 3.3, 3.0-3.9): likely; the step 1.5 past the lug's edge so the lug and the screw's hole stand on the full depth (estimated). Its plan stays the drawings', and its step is in question (the side views fix only a line across the plan; the loose piece once taken for it is the upper cock: Unresolved).
- The movement ring's screws: at 342.2°, 102.2° and 246.4° ±0.5 (both of Kirov 247's faces,
holemap.py --model wempeat 8.89 and 8.57 px/mm; Kirov 009's and Poljot 20027's the same: sure), so 120°, 144° and 96° apart, where the drawings put 340, 100, 220; steel slotted heads Ø 6.1 ±0.2 × 2.0 (drawn 6.2) where the drawings' are brass 6.2 × 3.05. The ring's band and its tapped holes per version.
- The bowl, re-measured: its outside with a pinhole camera fitted in the meridian plane, scaled by the rim's Ø 110.5, on Kirov 2973's bowl near side on (residuals under 0.3 px) and Kirov 247's: the thread r 55.25 down 5.55 from the rim's top, a collar r 56.6 to 7.76, the body r 52.4 (until then 51.8) to 46.7 (247: 47.0), a shallow cone to the foot r 36.7 at 55.3, the foot on to the drawn floor (its end isn't seen): likely. A cone that high leaves no room for the drawings' bore: the inside follows the outside, the bore r 49 then a cone 3.4 inside the outer one to the recess's wall (estimated; the movement's lowest parts clear it by 3.4 and more).
- The brackets, the high form (Kirov 247's own bowl,
11_,12_Kirow_247_E-Kontakt_*.jpg; Kirov 2973's the same; Kirow 422's too): each case bracket a flat plate 9.7 high (12.8 to 22.4 under the rim's top), its wings 27.5 either side of a block 8.7 wide which rises 1.8 over the rim's top, the pivot's hole 4.8 under its top (3.0 under the rim's top: ±2), the wings' slotted screws 16.8 from the block at 17.4 under, through the bowl's wall (the small holes in the bore of Kirov 247's and Kirov-Poljot 24020's bowls 16-21 under the rim are their ends: likely); the locking bracket an upright 11.7 wide, two screws in a vertical slot at 20.0 and 27.4 under, cranked out past the bezel to an L hook 3.8 over the rim's top, the pad the transit lock stops against (Romanov p. 204). So the 6MX's bowl, with its bezel, closing plate and movement, hangs 7.0 lower in the gimbals than the drawings' (13.2 until the drawings' case pivots were raised on 25 October 2026; case.js'sbowlS,DY6; app.js adds the movement to it); the later Kirov-Poljot 24020's pivots stand 10.8 under the rim, as the drawings' nearly do.
- The closing plate: a flat disc, no boss (Kirov 14917's foot square on, rAw2zmulpk8 0:11.75; Kirow 422's; a modern one, moMvyx8eXfo 7:20: likely), its screw's head about Ø 8 on its face, the domed knob about Ø 6.5 at r 19 ±2 (the drawings' 25); its groove, holes and spring as the drawings' (the spring unseen on any 6MX: Estimated), the spring's end shortened into the thinner plate.
- The outer box: its front about 233 wide (±7 %, the inner box's 190 scaled on
13_Kirow_247_Kasten_1.jpgand Poljot 08479's), the notch a circular segment, chord 102, depth 33 (until then a half-round r 48), the catch 51 under the parting line. The lid's tab reads larger than the notch (chord 105-111, 41-44 high) and may lap over the body's front: drawn filling it (Unresolved). The parting line's height and the straps' places are hidden by the bag (estimated as before).
- The seconds wheel: the gilt collet on its arbor under the wheel (
6_Kiro_247_S.jpg) is the contact wheel's (below). Pillar 39 reads Ø 8.0 ±0.5, the drawn 8.1; its radius stays 37.3 (Estimated).
- The electrical contact (Kirov 247's:
leben-des-6mx/10_-12_Kirow_247_E-Kontakt_*.jpg,6_Kiro_247_S.jpg,2_Kirow_247_A.jpgand3_Kirow_247_uZ.jpgagainst Kirov 1564's without one; Kirov 009's, 2973's, Poljot 08479's and Kirov-Poljot 24020's of the same design; Romanov 1975, p. 105's parts 52-69 and Figs. 100-101, p. 209; the user's choice, 17 October 2026, to build it). On the pillar plate's inner face by pillar 39, from 176.5° to 236°, a gilt base 58 (2 thick, its outer edge an arc r 45.7 past the plate's rim, cut round pillar 39; its inner edge from Fig. 100: estimate) screwed to the plate by two M1.7 screws 56 (above); on it, on black fibre 68 (1.8) and insulated by bushes 67 (their black flanges Ø 4.6 under the heads), two gilt blocks, 52 (+, 177.6-201°) and 57 (−, 209-231°), each held by two steel cheese-head screws Ø 3.1 × 2.6 (182.9°/193.3° and 214.6°/226.0°, r 43: the two steel heads seen under the top plate's edge are 57's); a gilt knurled contact disc 55 (Ø 11.9 × 1.2, 48 teeth) upright in its radial plane at 207.7° on a bracket on block 57, turnable to renew the contact (the user instruction); the lever 60 pressed on a staff 69 (206.2°, r 31.8 on Fig. 100 mapped, ±1.5; taken r 31.0, so the spiral's measured Ø 8.9 clears the disc) jewelled at both ends, a hole jewel and an end jewel in a setting in the base and in an L-shaped gilt cock over it under a cap plate, its stone 61 (a corundum pallet with a bevelled end) on the contact wheel 10.0 from the seconds arbor, its other arm (15.1) carrying the brass contact screw 54 with a lock nut, tangential at r 45.5, its point on the disc's low face; a flat copper-coloured spiral 59 (7 turns, Ø 8.9) from the staff's collet to a stud 53 on block 52, both the lead and the lever's return. The contact wheel 62 on the seconds arbor under its wheel (Romanov: fixed to it), on a gilt collet Ø 2.0 rising 3.0 above it (3.1 and 3.55 until 18 October 2026): 60 ratchet teeth, tips Ø 20.4 (likely), roots 18.6 (estimate), 8 spokes, one tooth left out. In the bowl, two flat brass springs 66 on black insulation, each held by two screws 65 through the wall, three tines bearing on a block's outer end; outside, their slotted brass heads and a brass socket for each lead, + at 200.6° and − at 235.9°, on black fibre washers, all 27.5 under the pillar plate's inner face (12_Kirow_247_E-Kontakt_3.jpg, a camera fitted on the band; the springs on11_and Fig. 101: likely; their sizes estimated, ±15 %). The heights from Fig. 101 (9.68 px/mm, which gives the seconds wheel's height to 0.06 and the 19 between the plates) and the S views (10.5 and 21 px/mm). Five more jewels, as the TU's 20 against 15 without the contact (checks.pyJEWELS). It works as Romanov (p. 209) and the user instruction describe it: the seconds arbor turns 3° a beat, half a tooth; on one beat the wheel's sloping flank lifts the stone (the lever turns about 4°) and the screw leaves the disc, on the next the tooth's radial face lets it fall and the spiral closes it: open half a second, closed half a second, and at the missing tooth closed a second and a half, at the minute (train.jsupdate,R.c6; which half-second is open isn't given: estimated). The parts the photographs show are where they show them; the stone and the staff's place, seen on no photograph, are Romanov's figure put on them (estimate). Rebuilt to the photographs (18 October 2026),10_Kirow_247_E-Kontakt_1.jpgthrough photocompare.py'sm6_contactcamera (0.6 mm at the block screws) and14_E-Kontakt1.jpg(another 6MX of the same design, them6_contact_frontcamera, about 1 mm): a millimetre scale stood at the staff, the seconds arbor and the screw's tip through the first gives the heights, and the two together give places across the view (they look along nearly the same line, 14° apart, so depth stays Fig. 100's). The cock's arm −12.9 to −14.2, 1.3 thick (−11 to −13.2 before), its leg run up to it; its cap plate three lobes, the two screws and the end jewel in a row 2.1 either side (along (−0.97, 0.24) as triangulated), the arm rounded r 1.6 past the far screw (a round plate with its screws 75° either side of the arm's axis before); the spiral at −11.7 to −12.3 just under the arm, its end run out over the stud and bent down onto its top beside the clamp screw (head Ø 2.2) (−8.5 to −9.1 before, from Fig. 101); the lever gilt (steel before), the contact screw Ø 1.0 threaded, at −5.85 (the photograph's −5.15 ±0.6 taken at the top of its range, to pass 0.1 over block 52's top), held in a gilt block under the lever's end with a brass lock nut 1.1 across; the disc's knurl square, its low face recessed Ø 6.0, 0.3 deep (estimated), a slotted steel axle screw (head Ø 2.6) in it, no raised boss. Left as drawn: the cock's leg renders about 2.5 further from the disc across the view than both photographs show it, within Fig. 100's ±2 but at its edge; moving it needs the arm's root and foot, whose depth no photograph fixes (Unresolved). The fine check required: the stone's end narrowed by its bevel (0.3 at its point), the stud's outer face at r 44.0, one block screw 0.15 off pillar 39 and the cock's screw and pins placed clear of its leg (each within its reading). The base overhangs the pillar plate's window for the intermediate wheel (0.23 over it), so in the Exploded view the 6MX's intermediate wheel leaves toward the dial after its bridge, as a watchmaker takes it out, the lever, spiral and cock lift clear of the contact wheel first, and its seconds wheel rises 30.6.
- The page's physics (the user's choice, 17 October 2026): the 6MX runs its own escapement,
WPHYS.rev('6mx')with its weighed bodies (WESC.SET6, checked bytools/wempe_6mx.jsagainstwempe_inertia.py --rev 6mx), its swing table and its 35-day trial (WEDATA.rev6,wempe_essaydata.js, its children run as the 6MX:wempe_load.js'sMC_WREV), in the Swing and isochronism and the Rate and trial panels and in the export to Blender. With the contact wheel weighed on its seconds arbor (the escape arbor's body 10.89 g·mm² against the drawings' 9.96), its swing is under the drawings' over the whole wind (190.2-200.2° against 191.0-200.5°:tools/wempe_6mx.json, its escape arbor 10.19 g·mm² since 29 October 2026, the shorter pinion; 190.1-200.1° against 191.9-202.0° when first worked out), its rate against 12 h theirs to 0.01 s a day; the mainspring is the drawings' (the 1958 Navy repair book's 1.01-1.08 N·m fully wound is the first generation's MX, which a strip about 0.42 thick would give, but no 1950s source gives the 6MX's strip: Unresolved).
- The contact revised (24 October 2026). The lever's boss sits on the staff just under the spiral's collet (−10.2 to −11.5), not at the screw's height: on Kirov 2973 (
14_E-Kontakt1.jpg) and Kirov-Poljot 24020 (12_KirPol_24020_E-Kontakt2.jpg, 16.7 px/mm by the cock's arm) the boss is 0.1-0.3 under the collet, the staff bare steel under it, and the arm runs down from it to the screw's holder on block 52 (likely; Kirov 247's own lever is hidden behind the stud and holder). Both arms are drawn sloping from the boss to their ends at the old heights (−6.1 to −7.4); the stone arm's slope is estimated, since no photograph shows it. The staff is Ø 0.6 under the boss (8-11 px against the block screws' Ø 3.1 at 23-26 px/mm, a little further off: Ø 0.4-0.6) and Ø 1.0 above it. Until then the boss and both arms were flat at −6.1 to −7.4, 4.5 under the spiral, on a staff Ø 1.0 the whole way. The cock (its foot, leg, arm, cap plate and screws) was compared again on 2973's, 24020's and 247's photographs and left as it is. The block's stud has a real slot, 0.5 wide and 0.9 deep, square across the base (the loose block,8_Gangfeder_mit_Kloben_Rus_einfach.jpg, 30.3 px/mm: 15-17 px across, running about 12 px down the stud's side; likely), in place of the kit's 0.35 × 0.55 at an arbitrary heading. The 6MX's block has no Ø 1.3 hole between its near steady pin and the stud (25 October 2026, the owner's choice): 05 04 01-4 drills one there from the plate's face to the detent foot's M1, and the German block in10_Vergleich_CWW-6MX_Gangfeder_mit_Kloben.jpgshows it, but the 6MX's face is plain there on that photograph and on8_Gangfeder_mit_Kloben_Rus_einfach.jpg(at about 30 px/mm it would be 40 px across: sure). The drawn versions keep it. The 6MX face's dot between the stud and the far pin (about Ø 0.3, a small hole or a punch mark) isn't drawn. The whole contact (on the pillar plate, on the seconds arbor and in the bowl) is hidden on the page unless Variants' Electrical contact is set to Shown (contact=1in the link; the owner's choice, 24 October 2026); under?qait is shown, so every tool weighs and checks it as before, and the physics is the same either way.
Checked again against the photographs (29 October 2026). The 6MX's escapement, its block and the parts at their heights, each read on the photographs before the model's figures were looked at (Kirov 247's 8_Kirow_247_F.jpg at 18.3 px/mm, scaled by the escape wheel's tips, 257.5 px for Ø 14, and its pinion's Ø 2.97, 54 px; Kirov-Poljot 24020's 9_KirPol_24020_Feder2.jpg at 26.6): WEMPE-VARIANT-ESCAPEMENT.md at the root has every reading. Changed:
- The upright is slit along the banking screw, parallel to the plate, from its end into the screw's hole: a line about 0.1 wide on both chronometers, the thread showing in it, 2.85-2.9 from the end face on 247 and 2.8 on 24020 (sure). The loose block's face toward the plate is plain (X5), which a slit parallel to the plate doesn't contradict: it doesn't show from that side. Built 0.12 wide, ending in the hole (its far edge 3.07 from the end), the upright's end extruded across with the slit and hole in its profile, as the 1943 block's.
- The banking screw's head Ø 3.4: 3.45 ±0.1 on 247 and 3.43 on 24020 at the wheel's own scale (likely); the 3.2 came from scaling by the upright's 3.
- The escape pinion 3.77 long, from 11.15 to 14.92 under the escape wheel, its foot about 2.2 over the pillar plate (likely ±0.1): the 3.9 and 1.5 read on the same photograph came from a tip span of 247 px (17.65 px/mm), where the tips measure 257.5.
- The collet's end Ø 1.55: 1.37-1.57 on 247 at 6×, 24020's 1.58 (likely).
Matched: the base's 6.5 at its end, the stop screw's head (Ø 4.4 ±0.15, the model's 4.2) and place, the collet's length (5.19 ±0.1) and its diameter at the wheel, the wheel's rim 1.37. Not settled by any photograph: the adjusting slide and stud, the lower cock's plan and step (Unresolved), the upright's height (3.45 ±0.3 read against 3.0: possible) and the screw's axis 0.4-0.6 under its middle (one view: possible).
The sheet, Soviet 6MX against the drawings (18 October 2026). The panel's section after Variants lists every difference the 6MX version builds (app.js's X6: 22, grouped as frame, escapement, barrel, electrical contact, ring and dial, case and boxes), each with what the drawings have, what the 6MX has and how sure the reading is, as this section gives them. Choosing one turns the model to the 6MX and closes in on it, the rest see-through (VIEWER.focusOn, shared/viewer.js: the parts' box, or a place where a part's own box would lose the change, as for pillar 39, the hand-setting holes, hole 53 and the moved ring and dial screws); Drawings and Soviet 6MX flip the version where the camera stands; a view chosen, Reset, Back or Whole model ends it.
The geometry checks in the 6MX
The browser checks of section 1, run with the page set to the 6MX: its own parts, its case and boxes, against the same expected contacts and leftovers.
Its physics against the drawings
Its jewels in chatons change the holes' tolerance, not the train's efficiency (oiled steel in ruby and in brass has the same friction in the model's sources); its escapement at the first-drawn heights, with the first-drawn balance staff and collar, changes the bodies only, weighed on the page's solids in that version.
The escapement of 1943 against the drawings
The page's fourth version stands its escapement as the German movements photographed with the 1943 detent block are made: the first-drawn balance, rollers and escape
wheel at their heights, the 6MX's detent and the block with its banking screw (the model's README, "The escapement of 1943 as photographed"). Its plan is the drawings'
(the banking screw sets the drawn depth of lock), so, as for the 6MX, only its bodies change: weighed on the page's solids in that version and run through makeEsc
(wempe_1943.js: the swing at the reference 160.7°, as the drawings'), its bodies within 0.3 % of the drawings', whose run in time stands for it (dynamics.js --model wempe: 300 beats, no tooth lost; the swing 160.5° against
makeEsc's 160.7°; run on the 1943 bodies themselves before the discharge stone's move, 198.7° against 197.6°). The page itself runs the drawings' escapement in this version.
17. The builds: a Wempe to navigate by
What a maker would build to navigate by: about two miles of longitude a month, 8 s after 30 days at sea. As drawn, the balance swings 155-166° over the wind, under the sources' 225-270°; the depth of lock has a window of a few µm at best (section 12), too fine to set and keep as the stone and the teeth wear; and set as the 6MX passports show adjusters set the masses, it carries about 17 s after a month (section 21). Two builds answer it, and the maker chooses (the model's README, "The build"; each choice the user's, 19 October 2026):
- Both: the gold spring thinned to 0.06 over its first 3 mm from its bending point (Belyakov 1957: Lange's MX 0.06 at its bend; 05 04 01-2's 0.15 taken as the blank), which opens the lock's window to about 0.2 mm; the preload 0.8 g; endshake to the Soviet Navy's 1958 MX repair book; the temperature masses set to ±0.1° on more rounds of the trial.
- The 1940s build: the drawings' drive and their carbon-steel mainspring, 0.37. A stronger carbon strip is past steel's limit.
- The 1950s build: 1.26 times the drive (the repair book's mainspring torque), from a Nivaflex 45/5 strip 0.393 × 15 × 1,240 mm, its free curve set ×0.8 (Straumann's alloy, patented 1948: not in the Einheits-Chronometer's own decade; 0.377 at set ×0.6 until 19 October 2026, whose inner coils section 13's 3D analysis found at 3.25 GPa, past the alloy's 3.0: the thicker strip's are 2.88-2.96), its drive taken turn by turn through the drawn fusee (stronger fully wound, weaker run down); the maintaining spring banked while running, as the Hamilton's is.
- Winding, both builds: the key let back at the end of each stroke, never let go outright (section 13: let go, the blow dents the click and the click wheel's tooth and bends the maintaining ratchet's brass teeth; no fix a maker could make keeps every part within its material).
The drawn versions' cross-checks between makeEsc, dynamics.js and the tripping frame are calibrated on the drawn detent; on the thinned gold spring three of
them part on detail of the detent's motion (none bears on its safety), so each build is judged on what decides whether a made one works (wempe_build.js).
Since 11 November 2026 (the discharge stone at 05 04_1's 5°) both builds have their hairspring set against the escapement, a bench adjustment (the escapement gains with the swing; the spring is set to lose as much: the owner's choice), and their swing's floor is 150°. Both builds pass every line below: the 1950s build swings 197-209° over the wind, the 1940s build 174-182°, both under the sources' 225°. On 11 November the 1940s build was reported here as failing (a held tooth's stone lifted 84 % of the depth of lock, a tooth past at 1.02 times its drive). That was a fault in the tripping tool, found and fixed on 12 November: it pressed a held tooth on the stone through the one step in which the tooth comes free, throwing the wheel back at up to 11 rad/s, and in about 1 beat of 100 the tooth met the returning stone (5 wrong beats of 560 before the fix, none of 560 after).
Made to the tolerances, and after the bench
Each build's tolerances, bench and Monte Carlo, run as section 12's with the build loaded (MC_WREV=build40, build): 2,000 movements each.
18. The mechanisms in turn: wear, the key, the motion work, the estimates
The Hamilton's model was checked mechanism by mechanism, as a maker would take its parts, by five tools beside the escapement's and the train's (its build report's
section 11): wear, the key forced, the motion work, the train on sprung meshes and the estimates swept. The Wempe's counterparts follow, each reading the Wempe's own
data (wempe_strength.js's loads, gearing_wempe.json's windows, tolerances_wempe.json's lock window, mechanisms_wempe.json,
wempe_inertia.json) and its sheets. The train on sprung meshes (the Hamilton's traindyn.js) has no counterpart here: section 13's
wempe_transmission.js already runs every mesh tooth by tooth through the beat (the meshes' forces, which rattle, the seconds hand's bounce) and weighs every
body on the solids (its section 1; the escape wheel's inertia against WESC.SET's is invariants.py --model wempe's), so it is cited, not repeated.
Wear: how long each contact keeps its figure
Archard's law at every sliding contact (V = k F s / H; k from Rabinowicz, 1e-7 well oiled, 1e-6 poorly, 1e-5 once the oil has gone; the escapement runs dry, as a
chronometer's does, at Rabinowicz's unlubricated non-metal on metal, 1.5e-6), the loads wempe_strength.js's fully wound, each depth against the tolerance it eats.
An escape tooth's tip (gilt brass) wears as a wedge whose flat widens. The line is a service interval: the 1954 Soviet instruction's cleaning and fresh oil every three years
(6MX-figures.md, п. 19); the TU's ten years' service life is reported against.
The key forced
A strong hand on the key's Ø 34.5 paddle (Imrhan and Munoz-Vasa's handles carried on past their 19 mm, an extrapolation; Swain's 1.06 N·m beside it), wound against the stop, and turned the wrong way. The 1943 key (51 00 11) is a one-way clutch, its coil spring gripping the tube one way ("Linksaufzug b. Rechtsdrehung entspannt sich die Feder"); the 1940 key it replaced is one-way too, its click spring drawn round its pipe (05-01_6; read as a plain key until 28 October 2026). The table's wrong-way lines are what a key that grips both ways would do.
The motion work and the up-and-down work, made on a CNC
Each mesh tooth by tooth on dial.js's tables, its depthing window (closer until its tips reach the roots, wider until it loses contact or its hand has a
quarter of an hour of play) and the hole its stud must be bored to (gearing.js's rule, the window's close side less the stud's shake, halved). The cannon pinion's friction
window is wempe_transmission.js's (section 13), put as a weight hung on the minute hand.
The estimates swept, with the bench's correction
What wempe_tolerances.js (section 12) doesn't sweep: the balance's free run-down (TF) over 80-200 s with the strip the bench's run-down test chooses, the
pivots' shake against each mesh's window, the hairspring's length read four ways off 05 03_7, and its outer terminal curve formed by hand; for the drawings as last revised
and both builds.
19. Making it: the frame under load, the order it goes together, each part on the machine
Sections 7, 12 and 17 ask whether a Wempe made to the drawings would hold together, keep time and pass its bench. Three more checks ask whether it can be made and put together at all, each on the page's own solids: the parts that hold the pivots solved as elastic bodies under the mainspring's load, the movement taken apart and put back in the order a repairer's book gives, and every machined piece read against what a lathe, a mill and a drill can cut.
The frame under load
fea.py --model wempe (the Hamilton's fea.py, its parts, arbors and fixings in wempe/checks.py's FEA): each part that
holds a pivot of the going train (the pillar plate, the top plate, the barrel bridge, the fusee bush and the intermediate bridge) cut into brass bricks (E 100 GPa,
ν 0.34) from its solid, at two sizes, the coarser a check on the finer; loaded fully wound and run down with the chain's pull on the drums' common tangent (the spring's
moment at 05 06_20's level, wempe_physics.js, on the barrel's pitch radius; the fusee's radius and the chain's height at that turn) and each mesh's tooth force
with its pressure angle (gearing_wempe.json), shared between each arbor's two bearings by the lever rule; each part held at its screws, the top plate on the
three pillars (Ø 8.1, 19 long, bending as beams), the pillar plate at its rim in the movement ring, the parts put together by superposition. What it leaves out: the
arbors' own bending, the jewels' settings (taken as the brass round them), friction at the fixings, the cocks (they carry the balance, none of the train's load).
The order it goes together
The Einheits-Chronometer has no overhaul manual of its own in the set; the Soviet Navy's repair book of 1958 (Эксплуатация и ремонт измерителей времени,
pp. 59-60, "Порядок разборки и сборки") gives the order for the MX, its copy on the same frame, step by step: the hands, the dial, the motion work and the up-and-down
pinion from the dial side; then, dial down, the balance's cock and the balance, the detent's block, the barrel arbor's ratchet, the barrel bridge, the fusee arbor's cork
washer, flange and washer, the top plate on its three screws, and the rest; and together the same backwards. assembly.py --model wempe rasters every part as
assembled into columns 0.2 mm apart (exploded.py's and overhaul.py's method), freezes the movement in one state, and draws each step's parts
straight off along the arbors, or along a path of straight legs where a part leaves sideways: a pair fails if one passes through the other, or is dragged the long way out of a fit it sits in. Where the model's parts can't follow the
book, or a real movement takes a part off another way (unhooked, unwound, turned to a gap, slid sideways), the step says so.
Each part on the machine
dfm.py --model wempe reads every machined piece off its solid (screws, jewels, springs, the chain, the dial's enamel and the hands left out: bought,
stamped, rolled or wound): its sections sampled between every two heights at which it has a flat face, on a grid 0.01-0.06 mm square as the piece's size allows. It
reports, against stated limits: walls in plan under mm (fragile in brass; teeth left to the gear cutter), slots narrower than an end mill of
radius mm (a smaller mill, a slitting saw or EDM), the inside corners that mill leaves rounded, round holes and their depth over diameter (over
10 peck drilling, over 20 a gun drill or EDM; under Ø 0.2 a micro drill), the thinnest floor along the arbors, what is cut from each face and whether the piece is round
about one centre (turned) or nearly (turned, then cut), undercuts (material above and below a gap: a lathe's grooving tool, or a side cutter on a milled piece), the
setups that follow, and any void sealed inside one piece (it fails: no tool reaches it).
Every piece
20. The build book: what each part is made of, and how
The page's Making it (the Hamilton's maker's sheets, in the Wempe's words): each part card has its maker's sheet, its lines of the parts list with the fit
bom.py measured on the model, the material and treatment its own drawing gives (the title block's Werkstoff, the notes' hardening and tempering,
the surface marks, read off References/wempe/transcriptions/), and how it is made; its drawing to scale, drawn from the model's solids; and the whole
build book to print, ending with the bench's tests for the 1950s build (section 17). Nothing is filled from practice: a part whose sheet leaves the Werkstoff blank,
or which has no sheet in the set (the Wempe-Norm screws and pins, the parts drawn only on an assembly), says so. tools/wempe_makers.py writes the data
(wempe/js/makers.js; --check in ci.py), book.py --model wempe checks the book as paper (every shown line on a sheet, each
with a material or the reason it has none and a fit, every drawing at its stated scale and legible on A4).
235 lines as last revised (14 assemblies): 60 parts with their material on their own drawing, 161 without (56 Wempe-Norm parts whose standard sheets aren't in the set; the rest drawn only on an assembly, or with the Werkstoff left blank). 166 carry a fit measured on the model.
| How it is made | Lines |
|---|---|
| CNC milled or turned, the material the maker's choice | 64 |
| bought in or turned | 56 |
| CNC milled or wire-cut | 27 |
| bought in or made by a case maker | 22 |
| CNC milled or turned | 18 |
| bought in | 17 |
| CNC turned | 8 |
| by hand and special supply | 2 |
| special supply | 2 |
| by hand | 1 |
| special supply and hand work | 1 |
| special supply or by hand | 1 |
| cast and machined | 1 |
| joinery | 1 |
What needs a hand, or a special supply
| Drawing | Part | Material (its drawing) | How |
|---|---|---|---|
| 05 05 04-2 | Fassung (the seconds jewel's setting) | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 05 04-1 | Lagerstein f. Sek. (the seconds arbor's lower jewel) | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 03 01-1 | Unruhreifen (balance rim with arm, nickel steel and brass) | „Nickelstahl Sonderlegierung u. Messing“ (nickel steel, special alloy, and brass) | by hand and special supply: the cut bimetallic rim: 05 03 01-1's „Nickelstahl Sonderlegierung u. Messing“, a nickel-steel special alloy with brass fused or brazed on, turned, then cut through beside the arm and its masses' holes drilled; no stock supplier makes it: a maker fuses brass onto the nickel steel or buys a balance blank, then adjusts it for temperature on the trial (wempe_thermal.js, the Wempe README's "Physics: hairspring and temperature") |
| 05 03 02-1 | Spiralfeder (helical hairspring) | „Bandstahl 0,52×0,285 poliert“ (strip steel, polished) | by hand and special supply: the helical hairspring: 05 03_6's „Bandstahl 0,52×0,285 poliert“ wound 15 turns left-hand on a form, hardened and tempered dark blue on it, its terminal curves bent to 05 03_7 by hand with curve pliers on a drawing of them; vibrated against the balance (its tolerance) |
| 05 04 03-2 | Hebestein (impulse stone, sapphire) | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 04-2 | Auslösestein (discharge stone) | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 01-1 | Gangfeder (spring detent, drawing 1436) | „Stahl“ | by hand: the spring detent (1436, „Stahl“): one piece of steel, its spring (Federung) 0.07 thick (0.09 at its ends) and 5.0 long filed and stoned to its ring (the bench's test), the locking stone set in its pipe (Röhrchen); 1436 gives no hardening |
| 05 04 01-3 | Ruhestein (locking stone) | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 01-2 | Goldfeder (gold passing spring) | „Goldblech 333 federhart“ (gold sheet, 333 fine (8 ct), spring-hard) | special supply and hand work: 05 04 01-2's „Goldblech 333 federhart“: 8 ct gold sheet rolled spring-hard, from a bullion or jewellery supplier; cut, thinned at its bend (the build) and stoned |
| 05 04 08-1 | Deckstein (endstone), balance, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-2 | Fassung (jewel setting), balance, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 07-1 | Lagerstein (hole jewel), balance, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-2 | Fassung (jewel setting), balance, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 07-1 | Lagerstein (hole jewel), balance, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 08-1 | Deckstein (endstone), balance, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 08-1 | Deckstein (endstone), escape wheel, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-2 | Fassung (jewel setting), escape wheel, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-1 | Lagerstein (hole jewel), escape wheel, upper | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-2 | Fassung (jewel bush), escape wheel, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 06-1 | Lagerstein (hole jewel), escape wheel, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 04 08-1 | Deckstein (endstone), escape wheel, lower | not on the drawing | bought in: a synthetic jewel: choose the standard hole and outside diameter nearest the drawn (the hole to the pivot plus 0.01-0.02), or have it made |
| 05 07 00-6 | Zugfeder (mainspring) | not on the drawing | special supply: the mainspring: 05 07 00-6's strip, or the build's Nivaflex 45/5 (Straumann's, from a mainspring supplier) cut to 1240 mm, its ends formed, set |
| 05 07 04 | Kette (fusee chain) | „Bandstahl 5×0,3; 10×0,9; Präz. Rundstahl 0,6“ (strip steel 5 × 0,3 [the link plates, inferred]; 10 × 0,9 [the end hooks, inferred]; precision round steel 0,6 [the rivets, inferred]) | special supply or by hand: the fusee chain (05 07 04): links blanked from thin steel strip and riveted on pins; a chain from a watch-parts supplier, or blanked with a press tool |
| 05 07 03-1 | Band (fusee band) | not on the drawing | special supply: the fusee band (05 07 03, 0.22 +0.03 thick, 730 ±3 between its hooks; no width or material on its sheet): a rolled steel strip from a strip supplier, its hooks brazed on (1.3.43); a post-war GUB Glashütte's band was Sandvik's, 730 mm between its hooks and about 0.2 mm² across (chronometerbook.com, post 35, 10 January 2019). Fitting it (the same post): too springy to lay on the fusee beforehand, it is hooked to the fusee in place and wound on under tension, then hooked to the barrel |
The materials the drawings give
| Drawing | Part | Material | Treatment |
|---|---|---|---|
| 05 08 02-1 | Unterplatte (pillar plate) | „Messingblech 4 / SonderMs α-βGef.“ | none on the drawing |
| 05 09 01 | Oberplatte (top plate) | „Messingblech 4 / Sonder Ms α-βGef.“ (special brass, α-β structure) | none on the drawing |
| 05 08 00-1 | Pfeiler (pillar) | „Rundmessing 8,5 Din 1758 Ms 58“ ("hart" struck through) | none on the drawing |
| 05 08 05-1 | Federhausbrücke (barrel bridge) | „Messing blech 3,5 Din 1751 Ms 58“ | untoleranced sizes ±0,1 |
| 05 08 05-2 | Sperrkegel (click) | „Messingblech 3 Din 1751 Ms 58 federhart“ | untoleranced sizes ±0,1 |
| 05 08 01-2 | Schneckenfutter (fusee bush) | „Rundmessing 13,5 Din 1758 Ms 58“ | none on the drawing |
| 05 08 01-3 | Staubfutter (dust bush) | „Rundm s. 15 Din 1758 Ms58“ | none on the drawing |
| 05 08 03-1 | Unruhkloben oben (upper balance cock) | „Profilmessing 50×15×3,3×5,5 Ms58“ (the "5,5" likely) | blank (Rohmaß) Profil ×18; untoleranced sizes ±0,1 |
| 05 08 00-2 | Unruhkloben unten (lower balance cock) | „Profilmessing 20×10×8×3,3 Ms 58“ | blank (Rohmaß) Profil ×18 |
| 05 05 03-2 | Minutentrieb (centre pinion and arbor) | „Präz. Rundstahl 7,2 Din 175“ | „härten, 295° anlassen“ (harden, temper at 295°); surface ▽▽▽ ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 05 03-1 | Minutenrad (centre wheel) | „Messingblech 1,5 Din 1751 Ms 58 federhart“ | surface ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,01 |
| 05 05 02-2 | Zwischentrieb (intermediate pinion and arbor) | „Präz. Rundstahl 5,2 Din 175“ | surface ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 05 02-1 | Zwischenrad (intermediate wheel) | „Messingblech 1,2 Din 1751 Ms 58 federhart“ | surface ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,01 |
| 05 05 01-2 | Sekundentrieb (seconds pinion and arbor) | „Präz. Rundstahl 3,5 Din 175“ (precision round steel bar 3.5 mm, DIN 175) | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 05 01-1 | Sekundenrad (seconds wheel) | „Messingblech 1,2 Din 1751 Ms 58 federhart“ (brass sheet 1.2 mm DIN 1751, Ms 58 spring-hard) | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,01 |
| 05 03 01-1 | Unruhreifen (balance rim with arm, nickel steel and brass) | „Nickelstahl Sonderlegierung u. Messing“ (nickel steel, special alloy, and brass) | „∇∇∇ poliert“; surface ∇∇∇ ∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,03 |
| 05 04 02-2 | Unruhbutzen (balance hub, brass) | „Ms.“ (brass) | |
| 05 03 02-1 | Spiralfeder (helical hairspring) | „Bandstahl 0,52×0,285 poliert“ (strip steel, polished) | „härten, dunkelblau anlassen“ (harden, temper to dark blue); blank (Rohmaß) 0,52 × 0,285 × 603 |
| 05 03 02-2 | Spiralrolle (hairspring collet) | „Messingblech 3,5 (overwritten, likely 3,5) Din 1751 Ms 58“ | surface ∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 03 02-3 | Klötzchen (hairspring stud) | „Flachmessing 15×7 Din 1759 Ms 58“ | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 02 04 02 | Heberolle (impulse roller, beryllium copper; 05 04 03-1 in the coloured section) | „Kupfer Beryllium, Saphir“ (beryllium copper; sapphire) | none on the drawing |
| 05 04 05-1 | Gangrad (escape wheel, 15 teeth) | „Messingblech 1,6 Din 1751 Ms 63 federhart“ (brass sheet 1,6, spring-hard) | none on the drawing |
| 05 04 05-2 | Gangtrieb (escape pinion, z 10, m 0.263, and arbor) | „Präz. Rundstahl 3,4 Din 175“ (precision round steel ∅3,4) | none on the drawing |
| 05 04 01-1 | Gangfeder (spring detent, drawing 1436) | „Stahl“ | none on the drawing |
| 05 04 01-2 | Goldfeder (gold passing spring) | „Goldblech 333 federhart“ (gold sheet, 333 fine (8 ct), spring-hard) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 04-2 | Schneckenkörper (fusee body) | „Rundmessing 36 Din 1756(?) Ms 58“ ("Rundmessing 36", "Ms 58"; the DIN number reads 1756 or 1758) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,05 |
| 05 06 04-1 | Schneckenwelle (fusee arbor) | „Präz. Rundstahl 7,5 Din 175“ (precision round steel 7,5 dia, DIN 175) | untoleranced sizes ±0,1 |
| 05 06 04-3 | Schneckensperrrad (click wheel) | „Ms Blech 2mm DIN 17.51 Ms 58 federhart“ (brass sheet 2 mm, DIN 1751, Ms 58 spring-hard) | surface ∇∇ ( (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 00-4 | Deckplatte (cover plate) | „Bandstahl 24×1 Din 1016“ (strip steel 24 × 1, DIN 1016) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 00-2 | Vorreiber | „Präz. Rundstahl 14 Din 175“ (precision round steel bar 14 dia, DIN 175; "Rundstahl" cut off at the box edge, likely) | surface ∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 00-1 | Staubplatte (dust plate) | „Rundmessing 8 Din 1758 Ms58“ (round brass bar 8 dia, DIN 1758, Ms 58) | none on the drawing |
| 05 06 00-3 | Schneckenrad (fusee wheel) | „Messingblech 5,5 Din 1751 Ms 58 federhart“ (brass sheet 5,5 thick, DIN 1751, Ms 58, spring-hard) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 02-1 | Gegensperrrad (maintaining ratchet) | „Messingblech 3,5 Din 1751 Ms 58 federhart“ (brass sheet 3,5, DIN 1751, Ms 58 spring-hard) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 06 02-3 | Sperrkegel (click) | „Bandstahl 11×2 Din 1016“ (strip steel 11 × 2, DIN 1016) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,05 |
| 05 06 02-2 | Sperrfeder (click spring) | „Bronzeband 1,5×0,4 federhart“ (bronze strip 1,5 × 0,4, spring-hard) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 06 01-1 | Gegenfeder (maintaining spring) | „Bandstahl 35×1,75 Din 1016“ (strip steel 35 × 1,75, DIN 1016) | „400° anlassen“; „härten in Öl“; „310° blau anlassen“; surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,05 |
| 05 05 05-1 | Gegensperrkegel (maintaining detent) | „Bandstahl 2,25 × 18 DIN 1016“ (steel strip 2.25 × 18) | „härten in Öl, 310° hell-blau anlassen“ (harden in oil, temper light blue at 310°); „um die Bohrung 400° anlassen“ (temper round the hole at 400°); surface ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 07 01-1 | Federhaustrommel (barrel drum) | „Ms. 63 3“ (brass Ms 63, 3 mm, i.e. 3 mm sheet) | surface ∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 07 01-2 | Federhausdeckel (barrel lid) | „Ms 58 DIN 1751“ | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 07 02-1 | Federkern (barrel arbor) | „Präz. Rundstahl 14 Din 175“ (precision round steel 14 dia, DIN 175) | „härten bei 800(?)“ (harden at 800?); „anlassen 270“ (temper at 270); „Kegel 1:70 poliert“; „härten bei 800 / anlassen 270“; surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); blank (Rohmaß) 14 × 45; untoleranced sizes ±0,05 |
| 05 07 00-3 | Sperrad (set-up ratchet) | „Messingblech 3 Din 1751 Ms58“ (brass sheet 3, DIN 1751, Ms 58) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
| 05 07 04 | Kette (fusee chain) | „Bandstahl 5×0,3; 10×0,9; Präz. Rundstahl 0,6“ (strip steel 5 × 0,3 [the link plates, inferred]; 10 × 0,9 [the end hooks, inferred]; precision round steel 0,6 [the rivets, inferred]) | „leicht polieren“ (polish lightly); „∇∇∇ härten, 310° anlassen“; untoleranced sizes ±0,05 |
| 05 07 03-2 | Bandhaken rund (band's round hook) | „Bandstahl 10×0,8 Din 1016“ (strip steel 10 × 0,8, DIN 1016) | surface ∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,05 |
| 05 07 03-3 | Bandhaken f. Trommel (band's drum hook) | „Bandstahl 10×0,8 Din 1016“ (strip steel 10 × 0,8, DIN 1016) | surface ∇∇∇ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,05 |
| 05 02 02-1 | Wechselrad (change wheel) | „Messingblech 1,2 Din 1751 Ms 58 federhart“ | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); blank (Rohmaß) 1,2 × 22,5 × 22,5; untoleranced sizes ±0,1 |
| 05 02 03-1 | Stundenrad (hour wheel) | „Messingblech 1,2 Din 1751 Ms 58 federhart“ | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 02 04-1 | Auf u. Abrad (up-and-down wheel) | „Messingblech 1,2 Din 1751 Ms 58 federhart“ | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,03 |
| 05 02 00-1 | Minutenzeiger (minute hand) | „Goldin“ (a gold-coloured brass alloy) | „Oberfläche poliert“ (surface polished); surface ▽▽▽▽ (▽▽▽) (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 02 00-2 | Stundenzeiger (hour hand) | „Goldin“ | „Oberfläche: hochglanz poliert“ (surface high-gloss polished); surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 02 00-3 | Auf u. Abzeiger (up-and-down hand) | „Bandstahl 0,6 × 15“ | surface ▽▽▽ (▽▽▽) (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 02 01-1 | Sekundenzeiger (seconds hand) | „Bandstahl 30 × 0,6 Din 1016“ | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| 05 02 00-4 | Zifferblatt (dial) | „Messingblech 1,3 Din 1751 Ms 58“ (1,3 struck, pencil "1,2") | „Eisenblech 1,3 gebondert“ (iron sheet 1.3, bonderized); „weiß lackiert“ (struck through: white lacquered); blank (Rohmaß) 1,3 × 110 × 110 |
| R-05 01 00-1 | Gehäusetopf (bowl) | „Ms-Sandguß (Kokillenguß)“ | none on the drawing |
| 05 01 00-2 | Verschlußplatte (closing plate) | „Ms.“ (brass; sure) | surface ▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished); untoleranced sizes ±0,1 |
| R-05 01 01-2 | Glasrand (bezel) | „Ms.“ | none on the drawing |
| 00 01 01-9 | Firmenschild (maker’s plate), Type 3371 | „Alu 10“ | none on the drawing |
| P. 51 00 02-2 | Zunge (latch tongue) | „Eisen 10 × 4 blank gezogen“ | „gebondert, schwarz lackiert“ |
| 127-556.01 (52 00 16) | Überkasten (outer box): body and base plate, bleached birch | „gebleichte Birke“ | none on the drawing |
| 05 01 02-2 | Schlüsselmittelteil (key body) | „St. Az / Din 668“ ("St. Az" = bright-drawn steel ("Automatenstahl"/"Stahl, gezogen", inferred) to DIN 668) | „** (sure) = sand-blast, phosphate, spray black. - **Number note:** on the key assembly 51 00 11 this part is “; „sandeln, phosphatieren, schwarz spritzen“ (sand-blast, phosphate, spray black) |
| 05 01 02-3 | Schlüsselrohr (key tube) | „Ms. 58“ (brass, CuZn40Pb, inferred) | surface ▽▽▽ (DIN 140: ▽ roughed, ▽▽ smoothed, ▽▽▽ fine, ▽▽▽▽ polished) |
The 1950s build's deviations on the cards
- The gold spring thinned at its bend (both builds, the 1940s and the 1950s): „Goldblech 333 federhart“ (gold sheet 333 fine, spring-hard), as drawn; the blank 0.15 (05 04 01-2) thinned to 0.06 over its first 3 mm from its bending point, stoned or rolled; the rest as drawn. 05 04 01-2's 0.15 taken as the blank: Belyakov (1957, Table 3) gives Lange's MX 0.06 at its bend. Stiff, sprung back onto the horn after the discharge stone passes on the return, it sets the held tooth's stone ringing 113-116 µm; thinned it rings 44 µm and the lock's window opens from 15 µm to about 200 (0.101-0.281 mm at the 1950s build's drive: tools/wempe_detent_study.js, wempe_build.js).
- Mainspring in Nivaflex 45/5 (the 1950s build (Straumann's Nivaflex: patented 1948); the 1940s build keeps the drawn carbon-steel strip): Nivaflex 45/5 (Co 45, Ni 21, Cr 18, Fe 5, W 4, Mo 4, Ti 1, Be 0.2 %); cold-drawn strip 0.393 × 15 × 1240 mm, its free curve set ×0.8, aged to over 3000 N/mm²; coiled; greased. 1.26 times the drawings' drive (the Soviet Navy's 1958 MX repair book's mainspring, 1.01-1.08 N·m fully wound, against the model's 0.83), which no carbon strip gives within steel's stress: the swing at 12 h 203.1° against the 1940s build's 177.3°, its inner coils 2.88-2.96 GPa fully wound on Nivaflex's 3.0, 30 days at sea 6 s. From 1.07 times the drive the maintaining spring closes onto its banking while running, as the Hamilton's does by design (11.7 min on it while the key turns).
The book's last chapter: the bench's 15 tests (tools/wempe_bench.js, the 1950s build), each on its part's sheet too. Not in the book yet: an order of assembly (the Hamilton's is its manual's Sec. VIII reassembly; no Wempe or 6MX assembly instructions are in the sources).
21. Navigating by it: the position a made Wempe gives at sea
Sections 11, 12 and 17 ask whether a Wempe passes its trial, can be made to its tolerances, and keeps about two miles a month in the builds. This section follows the
whole chain a navigator depends on, from a chronometer as made to the ship's position. tools/wempe_navigation.js takes 2,000 made chronometers for each version,
as wempe_montecarlo.js makes them after the bench. Their swing sets how much the oil's thickening moves the rate, and they are adjusted as each version is: as last
revised, the masses within ±0.45° of their compensating place (the TU's trial, the 6MX passports' spread of C); the two builds within ±0.1° on further rounds of the trial.
Each one is rated over ten days in port and carried sixty days to sea on wempe_errorbudget.js's voyage: a winter port (55 °F) into the tropics (85 °F) over the
first twenty days, the scatter and drift calibrated on the 6MX's test cards, the barometer, the oil, and heavy weather one day in five. The navigator carries the rated rate,
as rating.py's backtest does, so the error at sea is what the rate has wandered from it, added up.
Four seconds of time are a minute of longitude, which is one nautical mile at the equator and cos(latitude) miles elsewhere. The route is estimated, since no source gives one: from 45° N in port to 15° N by day 20, where the box reaches 85 °F. The fix itself has an error too. Bowditch gives a celestial fix by an experienced observer in favourable conditions a probable error of about ±2 miles (The American Practical Navigator, Pub. No. 9, 2019, Vol. 2, Ch. 3, "Navigational Errors"). It is taken here as a circular normal whose median radius is 2 miles (σ 1.70 a side, 95 % within 4.16), and the clock's error is added along the parallel. The criterion was stated before the results were known: after 30 days without a time signal, the chronometer should add no more than the sight itself. Its longitude error at the equator must be under 2 miles in the median (Bowditch's probable error, and the user's aim of about two miles a month) and under 4.16 miles in 19 voyages of 20 (the fix's own 95 % radius). Each figure is itself a sample of 2,000 voyages, so each is judged with its sampling error: 1,000 bootstrap resamples of the voyages (seeded, the same each run) give each figure's 95 % interval, and a half fails only if that whole interval lies over its limit. A figure over its limit whose interval still reaches it passes within sampling: 2,000 voyages can't tell it from one on the limit. One whose interval misses the limit by under 1 % of it is on the line, reported and not failed (the owner's choice, 26 October 2026, when the 1950s build's 95 % figure came to 4.34 miles with its interval from 4.160, against 4.158, once the error budget's calibration was made to stop wandering with its random draws: before, a run could land it either side). The limits were not moved. The 1950s build must not fail, and the tool fails if it does.
22. An independent pass: can it be built, and would it navigate?
The per-part audit of 25-26 October 2026 (six batches, WEMPE-PROVENANCE.md) changed parts the analyses above rest on: the escape pinion (4.0 long),
the detent (its spring tapered, its heights), the endshake (0.06, the 1958 book's 0.05-0.07), the fusee body's place, the barrel's internals, the maintaining clicks and
springs, the case and gimbals, and the mainspring's set (×0.75). This section is not a rerun. It reads each analysis again, adversarially, and asks three questions. Does it
read the changed parts from their one source, or from a copy of their old numbers? Do its criteria match their sources? What does it assume that a maker couldn't meet?
Two read-throughs were made, one hunting stale numbers and one weighing criteria and assumptions, and every finding was checked against the code before anything was changed.
Stale copies, found and fixed
- The detent spring's thickness on the bench. Since 25 October the tripping frame takes the spring's thickness as a factor of the tapered spring's uniform equivalent,
0.0792 mm (1436's 0.09 at its ends and 0.07 at its middle). The bench's ring test (
wempe_bench.js) still divided by 0.07, so every thickness in its table was a spring 13 % thicker than its label. Its band read 83-164 Hz; it is Hz, the spring as drawn ringing at Hz. The Monte Carlo (wempe_montecarlo.js) centred its detent springs on 0.07 against a band centred on 0.0792, and so replaced 4 springs in 2,000 movements that needed none (0 now). Both are fixed, and the bench, the Monte Carlo and the maker's sheets are rewritten for all three versions. No verdict changes. - The escape pinion's face in
wempe_train.jswas still 3 long (4.0 since the audit). Every mesh takes the narrower face, the wheel's rim, so no figure moves. - The damping measured on video (
wempe_startup.json) had been fitted on 19 October, before batch 1 changed the balance's inertia and the detent's. Refitted on the escapement as it was that day, it gave TF 114.4 s (111-118); the model kept 111 s (the owner's choice, 26 October 2026), inside that range, andwempe_escapement.jschecks that the model's TF lies inside the fit's range (it asked for within 2 s of its middle). The escapement's reconciliation and the detent's blade have since moved the fit to TF : the model keeps 111 s outside it (the owner's choice, 27 October 2026), and the check reports it. - Left as they are, no verdict moving: the frame's load takes the chain's radius fully wound as 9.355, the fusee's table at 8.75 turns, while the strength checks take its last entry, 9.30, a quarter turn past (0.5 %, the cautious side): both read the table, neither stale;
wempe_wear.jstakes the maintaining clicks' spring force as an estimated 0.44 N, andwempe_ratchets.jstheir springs' free span as 12-16, neither from the clicks as re-drawn in batch 5; the trial's label now reads "GOST 8916-58's class II trial, its limits GOST 8916-70's class 2" (6MX-figures.md).
Everything else reads its source: the energy budget's level (0.913) is computed live from the re-solved spring; the gimbals' bodies come from gimbals_wempe.json, reweighed
after the threads (periods 0.67 and 0.77 s); the bench's endshake stacks agree with the escape arbor's and the fusee's drawn lengths; the chain's lever on the stop and in the
strength checks is the fusee's own table's.
The criteria against their sources
| Criterion | As the tools encode it | The source | Agreement |
|---|---|---|---|
| The TU's trial | 36/20/4/20/36 °C, the first 2 days of each period not counted; E 0.35, R 2.00, D 2.30, C 0.10, S 1.20, ω 3.50, N 30 (wempe_errorbudget.js) | TU 25-07-1533-84, Table 5 (6MX-figures.md): GOST 8916-58's class II trial, GOST 8916-70's class 2 limits | every limit and formula matches |
| Endshake | fusee 0.08-0.12, escape 0.05-0.07, balance 0.04-0.06 (wempe_bench.js) | the 1958 repair book, Appendix 4 | matches |
| The swing | a guard band over the whole wind, 147-270° for the drawn versions and 150-270° for the builds (wempe_build.js, wempe_tolerances.js, wempe_montecarlo.js; 180-270° until 11 November 2026) | 225-270° (the 1954 instruction) | relaxed, and the tools say so: the drawn version (155-166°) and both builds (the 1950s build 197-209°) swing under the sources' 225° |
| The fix's error | a 2-mile median radius (σ 1.70 a side), its 95 % radius 4.16; the clock's error along the parallel against that radius (wempe_navigation.js) | Bowditch: a fix "seldom in error by more than 2 miles" | the arithmetic is right, the reading the lenient one: "seldom" reads more like a 95 % bound, and the clock's error is along one axis. Both stricter readings are reported below; the verdict stays on this one (the owner's choice, 26 October 2026) |
Can it be made and put together?
Yes, as drawn, with the work a 1950s shop would expect, and on nothing a maker can't do. Section 19's checks run on the page's own solids, which since 26 October carry
their threads (ISO metric, the tapped holes threaded and each screw on its hole's helix). dfm.py finds no void sealed inside a piece. What it flags is ordinary
watchmaking: walls under 0.15 mm (the escape wheel's and fusee's teeth and groove lands, the cannon pinion), two slots narrower than a 0.4 mm end mill (the upper cock's and the
fusee's: a slitting saw), undercuts on eleven milled pieces (a side cutter) and the sharp inside corners an end mill leaves rounded. It also reads eight holes of Ø 0.077 in the
fusee body, which no sheet has: a reading of the groove's surface, to be confirmed. assembly.py takes the movement apart and back in the 1958 book's order with nothing
passing through anything. The fits the sheets left impossible were found and corrected by the audit itself (README, Readings corrected; the collet's bore against the 1946 staff,
the hour wheel's collar against the dial). One fit a maker must make on the bench: the endshake. Made to the sheets' fits, every one of the Monte Carlo's 2,000 movements has
some arbor outside the 1958 book's band (about five arbors each out of band, some of them binding), and the bench sets each.
Would it keep time to navigate by? The chain and its weakest link
The chain is the made chronometer's swing (wempe_montecarlo.js), its trial and voyage (wempe_errorbudget.js) and the position (wempe_navigation.js).
What each source adds alone after 30 days at sea, median |error|:
As adjusted on the TU's trial, the masses set to the 6MX passports' ±0.45°, the temperature's residual dominates: the rate moves by up to 0.1 s a day for each °C, and the voyage climbs 16.7 °C in its first twenty days. With the masses set to ±0.1° (two or three more rounds of the 4 °C and 36 °C periods, about two weeks on the bench), drift becomes the largest term. That is a slow change of rate, calibrated on eight test cards as a constant slope, which a ten-day rating in port cannot see.
Why the drawn version fails. It is mostly not the low swing. It is the masses' setting: run the drawn escapement with the builds' ±0.1°, and it carries . The swing (161°, from the drive and damping the owner chose) is left only the difference between that and the builds' figures. Where the swing does matter is over a year rather than a month: with the drawn hairspring the drawn version's rate moves about 2 s a day for each 10° of swing, where the builds' hairspring is set against the escapement's gain, so as the oil thickens between services it wanders more, and each voyage's fresh rating has more to take out.
What a maker must do on the bench
Pass the TU's trial; then keep repeating its 4 °C and 36 °C periods, five counted days each, moving all four masses by C/0.228 degrees each round (a pair alike, to keep the poise), until |C| is under 0.023 s a day per °C. That step decides whether a made one navigates. Then set every arbor's endshake to the 1958 book's band, the banking to the middle of the lock's window and the preload to its aim with wire riders, replace a detent spring that rings outside its band, change the strip if the mainspring's pull is out of its band, and turn the set-up until the swing stays in band over the whole wind (section 17's tests).
What the model assumes the maker achieves, and doesn't model. The ±0.1° assumes that a compensation, once set, holds: that moving the masses and tightening them again doesn't shift the poise, and that the nickel-steel rim doesn't age between the trial and the voyage. The scatter is white noise, and the drift a constant slope. The oil loses 0-10 % of the drive a year, linearly, its viscosity's change with temperature left out (it matters most to the drawn version). Missed or irregular winding is not modelled.
The verdict, version by version
23. What stays open
What the sources haven't settled, as the model's README lists it ( questions), each with the reading the model takes and what would settle it:
- The 6MX's bowl can't be turned over in its gimbal ring (the 6MX case review, A1,
6mx-audit/case/README.md; settled 9 November 2026, kept here for what stays unknown): its pivots stand 0-3 under the rim (Kirov 247 0 ±1.7, 2973 2.5 ±1.5), and its ring reads Ø 133 ±3 inside with the bowl 67.5 overall (blind-ring-foot.md, read blind). So a 1950s Kirov's bowl can't turn over inside its ring, while later Poljots, with lower pivots, are turned over in theirs (Poljot 09777, Uy8A88_j-cA 5:14-5:27). The owner chose to make the 6MX's ring 133 inside and 3.7 thick (estimated: one blind reading, no camera), and to have its Wind turn the ring and the bowl together about the box's pivots. How a Kirov of the 1950s was really turned to be wound isn't shown on any source. In that ring the bowl swings ±28.5-30° before it meets the ring. - The 6MX's transit lock (the same review, A2): fixed on 8 November 2026 at the owner's choice, as the drawings' lock: the lever at the pivots' height through the ring's slot into the hook, turning 48.8° (swept clear against the column and the ring). The lever's height and turn on a 6MX are not read on any photograph (estimated: the hook's slot height, Kirova 14100's ring slot and Romanov's text are the evidence).
- The 6MX block's near steady pin against its end face (7 November 2026, the 6MX audit:
6mx-audit/beta.md). Re-read blind on Kirov 247's and Kirov 1564's plans (tools/m6cam.py,m6meas.py, held to holes 11, 12 and the escape arbor), the pin's hole stands at (-29.98, 21.88), 10.23 from the far pin (likely, ±0.15). In the block's frame that is 0.26 inside the end face, where the pin's r 0.45 hole would break out of it. The loose 6MX block (8_Gangfeder_mit_Kloben_Rus_einfach.jpg, by its stud's Ø 3.38) has its near pin 2.25 inside, the drawn pattern, so it doesn't show 247's. So either 247's block stands about 0.25 farther out than the model places it, or its pin is in another place. The pin stays at (-30.0, 21.55), 0.57 inside. Settled by a photograph of a 6MX block, loose or out of the plate, with the pin and the end face on the same face. dialsvg.py --verifyon Kirov 247's red serial (28 October 2026, the second drawing check's 7-M9): it exits 1 on the 6MX's dial, the red serial 10.62 mm² in the SVG against 10.54 on the page's canvas, 0.75 % against its 0.5 % limit; every shape agrees (0 px differing 3 px across) and the black ink of all three dials is 0.10-0.13 % over in the SVG. The excess is the same rasterising edge bias in all of them (the SVG's fill a fraction of a pixel wider along every edge), which on the serial's thin strokes, with several times the black ink's edge for its area, is a larger share: not a fault of the traced serial (dialface_kirov.js), whose outline is the photograph's. Left as it is: an area limit that knows the shape's edge length (or an absolute floor for so small an area) is the tool's to settle;ci.pyruns only the stale check, which passes.- The escapement's dry tip wear short of a service interval (28 October 2026; the owner's choice: reported soft,
~~). With the gold spring's bending point at 05 04_1's drawn mark (6.15 from the stone, the second drawing check's 2-M3: sure; 6.7 before), the strip is stiffer and the lock's window narrows to 231.7-237.2 µm (237.9 before):wempe_wear.jsfinds the escape tooth's tip, run dry, wearing through the lock's room in about 2.8 years against the 1954 instruction's three-year interval (about 3 before). Oiled, every contact lasts far longer. To settle: whether the drawings allow a wider window (the drawn depth of lock, the preload, the builds' thinned gold spring). - makeEsc's work stepped by its own ride steps (27 October 2026, the owner's request to improve the isochronism;
tools/wempe_cliff.js): the 0.29 s a day dynamics.js's cross-check found over the wind was makeEsc's, not the chronometer's. Its ride through the impulse timed each landing of the stone on the escaping tooth's back at the end of a quarter table step, which stepped the work 1-3 % about a degree apart and held the full-wind swing at 200.9° where dynamics.js runs at 204°; refined to 32-128 steps it converges on 203.9°. Each landing is now timed inside its step, the ride stepped eight times a table step (RSR) and the swing solved on the work averaged over ±0.5° (SMW): half the 0.98° the impulse raises the swing within each beat, since a real dip half a degree wide (201.5-202° at full wind) remains, which the balance crosses every beat. The swing over the wind is now 192.5-203.9° (197.4° at 12 h), the escapement's change over it +0.93 s a day against dynamics.js's +0.84 (−0.08 apart, the check back to 0.2), and with the drawn hairspring (HS −0.485) the chronometer's rate over the wind −0.14 to +0.24 s a day. What remains is the chronometer's own: the escapement gains about 0.8 s a day for each 10° and the drawn spring loses 0.49. Averaging changed nothing at 4 steps (the steps there are deeper than the window). The page reads the swing offWBANK.amp(tools/wempe_banking.js), a solve taking about a second. - The let-off in heat (27 October 2026;
tools/wempe_thermal_frame.js, the report's section 9, "The frame, train and escapement in heat and cold"). Over the TU's 4-36 °C the train's depths, the endshakes, the depth of lock and the chain move under 4 µm, but the steel detent grows less than the brass frame that holds its foot, so the gold spring's tip draws 1.8-2.3 µm away from the staff at 36 °C (the published constants' middle and the corner that moves it most), taking 0.3-0.45° of the drawn 1.50° let-off. At about 1.0-1.1° the escapement loses its impulse (the tooth runs a pitch before it lands on the impulse stone: makeEsc, anddynamics.js --model wempein time on the same settings, the swing 91-97°): the same edge that topswempe_tolerances.js's lock window (its deepest lock lets off at 1.12°). The drawn lock (235 µm) holds at the constants' middle and not at the corner; the bench's (the window's middle, 238 µm) fails at 36 °C at both. The window that holds over 4-36 °C is 231.7-237.9 µm at the middle (6.2 µm wide against 12.7 at 20 °C), none at the corner. The owner's choice (27 October 2026): the window over 4-36 °C is the window.wempe_tolerances.jscaps its top at the deepest lock set at 20 °C that keeps the swing in the guard band at the wind's lowest at 36 °C (wempe_escheat.js, the constants' middle): 231.7-237.9 µm (237.9 against 244.4 at 20 °C alone). The bench aims just under its top, 237.8 (the owner's second choice that day): a worn tooth's tip only makes the lock shallower, away from the let-off's cliff, and the dry escapement's tip wear (wempe_wear.js, about 2.1 µm a year) wants about 6.2 µm over the floor for the 1954 instruction's three years between overhauls, which the window's middle (234.9, 3.2 µm) gave for only 1.6; set there, a chronometer at the constants' middle has no heat margin at 36 °C until the teeth wear; the 1950s and 1940s builds' windows lose about 5 µm at the top (102.9-273.1 and 113.7-270.5 µm at the corner, 1 November 2026). Every version still works after the bench in the Monte Carlo (100 %). Still open for the drawings' version alone: at the constants' corner its window over 4-36 °C is 231.7-235.2 µm (3.5 µm wide), the bench's aim past it, the let-off 0.98° at 36 °C; more let-off (the discharge stone's reach or the gold spring's tip, both estimated where the sheets don't size them) would widen it. Closed for both builds (1 November 2026,wempe_thermal_frame.jsunderMC_WREV=buildandbuild40): their thinned gold spring gives 2.72° of let-off at the drawn lock, 2.38° at 36 °C at the corner (the cliff about 1.0°), and their windows over 4-36 °C are 102.9-273.1 µm (the 1950s build) and 113.7-270.5 µm (the 1940s) at the corner, the bench's aims (188.8, 193.0) well inside; every case passes, the swing over the wind 224-238° and 197-208° at the drawn lock in heat and cold. The escapement's and drive's share of the rate is small (C +0.008 s a day a °C, S +0.09 s at the middle). - The stone's blow on the escaping tooth's back, on a cliff (26 October 2026; the owner's choice: recorded, the transmission check's bracket reported). With the escape wheel as drawn (its web 0.7: the arbor 8.28 g·mm², JW 9.53), the locking stone, flung off the discharge stone and falling back, catches the escaping tooth's back 0.6 µm above its banking just before the back's end passes (13.47° of the balance, the back running away at about 0.29 m/s); its plastic landing pushes the wheel and gives the balance 0.0024 k a beat, 3.4 % of the impulse, 2.4° of swing. Whether it lands at all turns on a microsecond: with 0.25 g·mm² more at the escape wheel (8.82 and up) the tooth has passed first and the blow is gone. makeEsc counts it since then (
RWD, Wempe only: the Hamilton's figures bit for bit), and agrees withdynamics.jswithin 1.2° and 0.3 s a day over 8.0-8.9; the meshed train inwempe_transmission.jslands as a rigid train of about 10.2, past the step, so its impulse work falls outside the two rigid trains it is bracketed by (reported,~~). Until then makeEsc and the time model agreed only because at the old inertia (8.73) the blow had nearly vanished. The landing's plasticity and the back's end are estimates; a made Wempe's swing could sit either side of the step. Since 27 October 2026 (tools/wempe_cliff.js, which maps the work's steps about the swing at each drive and the beat's closure over the wind): with the blade centred the swing was held on that step at every drive (the step within 0.2-0.4° of the solved swing at 90-105 %, the beat closing 0.955-1.058 over the wind; wempe_escapement.js checks 12 h alone, 1.013), a stable pinning (under the step the blow adds work and the swing rises, over it the swing falls). With the blade built and the discharge stone's reach taking the gold spring's tip's slide about the offset flexure (Readings corrected) the step lies 3.5-5° under the swing at every drive from 85 to 105 % and the beat closes 0.97-1.01 over the wind (1.000 at 12 h); what is left is the stone's hops on the back through the impulse, a roughness of about 3 % (the swing at full wind held on one at 200.9°). The 6MX's heavier escape wheel (JW 10.45) puts its swing on such a hop's step at every drive (its beat 0.95-1.06; unchecked by the tools; clean with the blade centred). - Left open by the drawings check (26 October 2026, PLAN-wempe-drawing-check.md; each batch's report in
drawing-check/, the ledger WEMPE-DRAWING-LEDGER.md). Corrected meanwhile are listed in RESOLVED.md; these are the readings no sheet settles, the sheets' own conflicts, and what the model can't yet build:- Kept, the sheets' own conflicts (27 October 2026, the open items settled): the set-up click's 17,4 overall against 17.53 from its 9,7, 7,5, r 1 and the base line (05 08 05-2: the figures drawn); the stop work's C-D (05 06_4) read from the hub Ø 21, its "1,76" 0.1 and "3,2" 0.16 off the bar the 22,5 and the "2" fix (the drawn bar kept; Estimated); the block screw on the plate table's hole 13 (23.41, Wempe 3955 23.36) against 05 04_1's 23,8; the Lange dial's own disc (1453/A) not built, the variant the printing only; the stud's round point and pin hole (the blank's, drilled at assembly); the bowl's tapped holes for the brackets' screws (embed). Each sheet's reading in the ledger WEMPE-DRAWING-LEDGER.md.
- Readings not settled: the lid plan's Ø 6.4 circle (05 07 01-2).
- Built short of the sheet, the tools' limits: the hairspring collet's cross hole, drawn 0,8 +0,01 tapering 1:90 to (0,77) (05 03 02-2; the parts audit, 3 November 2026), is cut straight 0.805: bore() and the recipes' Drill cut straight holes, and the taper is 0.03 over 2.6; the 1941 barrel arbor's hook hole's drill point (0207 draws it beyond the 6, which ends on the line dashed across the hole: bore()/holeCut end a hole flat; tried 1 November 2026: cut with the hole's sides in one pass, holeCut twisted the walls' sections across the 24-gon's corners, leaving a 0.01 gap seatcheck's rays passed; cut as a second pass under the floor, the arbor came out open. An offline boolean as the fusee body's, wempe_fusee_body.py, is the way left); the upper cock's setting screws' holes plain where they pass through the boss (they leave through its side); the first-drawn block (05 04_1's) not built apart; seams where fused pieces meet face to face (the fusee bush, the ratchet's cup, the detent's pieces).
- Closed since (1 November 2026): the blind steady-pin holes in the cocks and bridges (41, 47; 6, 9, 50; 22, 37; 29, 44) end in the drill's 118° point beyond their 2,5, as 05 08 05-1's side view, 05 08 00-2's and 05 08 03-1's A-B and 05 08 04's section draw it (the angle not figured: the drill's own, the owner's choice; solidGeo's
tip, kit.js, frame.jspinPt); the 1943 arbor's hole right through its core as 05 07 02 dashes it (fusee.js's fillOpen closing the three edges its far mouth left open). The masses' screws WN-12 keep their heads' faces finished to the mass's round side, flush: Wempe 3955's balance (9_Wempe_3955_Hemmung.jpg) shows the slotted head flush in the round side and no flat milled round it, and 05 03 01's plan (a poor copy) draws the head's end straight inside the outline, which can't tell a flat from a spot face (the owner's choice, 1 November 2026: no flat seat; "the radial seat" was listed here until then).
- Kept, the parts audit's four clashes (3 November 2026, the owner's choice: keep the fits, record them; the parts audit
WEMPE-PARTS-LEDGER.md, explained inparts-audit/FINDINGS-EXPLAINED.md). Each is a later or other sheet whose size, as drawn, would not fit a part whose sheet was not redrawn with it, with no assembly sheet or photograph to settle the pair:- The escape wheel against the detent (A1): 05 04_1 (3.2.40) draws the wheel's centre under the locking stone and 23,8 to the block screw; the model takes the top plate's table (05 08_1, 15.6.43; hole 13 at 23.41; Wempe 3955 23.36 ±0.15), so the wheel stands 0.447 along the detent and the detent is turned 3.6-4° about its pipe from the layout's square.
- The 1946 pinion pivots (B1): 05 05_4 (rev. 24.3.48) and 05 05_7 (6.6.46) print pivots 9,2/4,5 and 4,6/4,6; as drawn they would stand 1.1-1.5 out of the top plate and the intermediate bridge, whose sheets are older; the model keeps the assemblies' 7,2/3 and 3/3 (05 05_2, 05 05_5).
- The fusee arbor's journals (C2): the arbor (05 06_15, 29.11.40) is 2,8 at the pillar plate and 4,5 in the bush and wheel; the pillar plate (hole 10, 2,70 ±0,009, 23.4.43), the bush (4,1 +0,2) and the wheel (4 +0,1) can't take it; the model keeps the arbor and opens the holes (2.82, 4.52, 4.55).
- The hour wheel's collar (E1): 05 02_8 (1940) draws it 5,2 -0,1 above the foot; with the cannon pinion's tube (05 05_8, 22.7.43) it would reach 1.4 into the dial's Ø 6 hole; the model keeps 3.585, 0.3 under the dial.
- The rigid train against the train on its meshes (19 October 2026, the physics pass; traced 25 October 2026):
wempe_transmission.js, the whole transmission as bodies on its meshes, gives an impulse 5.1 % more work than the rigid train makeEsc, dynamics.js and the page take (3.8 % before the per-part audit's first batch reweighed the bodies; 2.1 % with the lock at 0.175, the preload 0.63 g and TF 108 s); as a drive it keeps the swing 6.2° higher than the rigid train's at 12 h. The cause is the train's backlash, not its meshes' give: stiffer meshes don't close the gap (×100 at a quarter of dynamics.js's step, which stiff meshes need: +4.5 %; ×0.5 +6.2 %; as drawn +5.1 % at either step), while the last mesh, the seconds wheel on the escape pinion, lets go about 1 % of the time: the escape wheel lands dead on its stone, the seconds wheel runs on into the backlash (170 µm), and at the release the escape wheel starts free of the train behind it. The tool now runs both rigid bounds, the whole train's inertia at the escape wheel (10.01 g·mm², makeEsc's JW 9.98) and the escape arbor's alone (8.73): 11.655 and 13.560 µJ, the meshes' 12.254 between them, 31.5 % of the way (a check), as a rigid train of about 9.68 g·mm² (9.61 interpolated linearly; a rigid twin at 9.61 comes within 1.1 %). Left for the owner's choice: makeEsc's Wempe JW at that equivalent inertia would raise the model's swing by about 6° (escgolden.js untouched: a Wempe setting); the drawn backlash is the teeth's own, so the meshed train is the better model of it. The check stays at 8° and 0.5 s a day until then. 28 October 2026: with the escape wheel's speed in the coupling dynamics.js's own (Physics: the transmission), the figures above no longer hold: the two rigid bounds give 13.713 µJ (the whole train, 9.56 g·mm²) and 14.430 (the escape arbor, 8.28), the meshed train 13.341, outside them on the low side (−52 % of the way, reported), as a drive −3.74° of swing on the mean of the 8 starts. The differenced speed's false kick at each impact had been adding about 2.4 % to the meshed train's work; what the backlash's equivalent inertia is, now that the meshed train sits below both bounds, is open. - Wempe 3955's closing plate (
16_…Gehäusetopf_Kardan.jpg) shows two holes about Ø 1 in the boss's face, at r 11.2 and 11.9 and about 160° apart about its screw (not opposite: 16 October 2026), where 05 01 00-2 draws one Ø 1.2 at 12.4, blind from the other side (built as the sheet). They look added on that chronometer (a pin spanner's, perhaps: moderately sure). The 6MX has no such plate (a sliding shutter; Kirow 422's bottom,11_Kirow_DEC_422_Gehäuse.jpg, a flat disc); GUB 11307's (Rwr93vdA8cw 9:34, 9:48, about 9 px/mm) has a plain boss face round its screw, as the sheet's blind hole would leave it. Another wartime bowl's back would settle it. A Wempe Typ 04 of the war (Luftwaffe No. 2974/2978, Klassik Uhren 3/2006 p. 21, Knirim's photograph) shows its bowl's back: a central slotted screw, a round hole off it and a second small screw; another chronometer's bowl (the lever's, with its holding device's fest/frei knob), so it doesn't settle the Einheits plate (31 October 2026). - As first drawn: 05 04_7.1 draws the escape wheel's recess Ø 11.9 (altered to 12.4 in pencil), 0.7 deep, on the plate's side, as 05 04_1's elevation has it (its dashed walls run from the floor to the wheel's face toward the "2" end, the plate's: 16 October 2026; read as the pinion's side until then), the walls scaling Ø 11.8; against the 1942 tooth form's floor Ø 11.7, which 11.8-12.4 would cut: the wheel is drawn as 05 04_1 and 05 04_23 have it. The collar's boxed 4.7 puts the impulse roller 0.6 under the plate where 05 04_1 scales 0.39-0.42 (the figures built). The pipe on the stone (1.95-3.65 under the plate, estimated): 05 04_1's elevation draws it dashed from 2.26 to 4.35, 1.04 below the blade, the stone hatched from 0.33 down inside it (24.4 px/mm; likely), as 1436's right view does (2 (1.9) long, past the blade's pillar-plate side); built so, its lower end would run 0.65 into the block's arm as built (3.7-6.5 under the plate:
fine.py), so the arm's height or its near face's place in plan is also in question: kept as estimated. The 1941 banking screw banks the pipe's lower end (likely: its slotted head, Ø 2.28 at 5.17 under the plate on the arm's slit, covers the pipe's last 0.3 in the elevation; Wempe 3955's domed end just under the blade). Wempe 3955's escape wheel collet (10_Wempe_3955_Feder_plus.jpg, 11.8 px/mm by the wheel's Ø 14) is one gilt cone about 6.4 long, Ø 3.4 to 1.3, like the later 05 04_7.2's, where 05 04_7.1 draws a cone Ø 3.0 over 1.8 and a pipe Ø 1.8 to 5: built as the sheet (moderately sure of the photograph's reading). - The pillar plate's thickness (struck, above): the replacement figure on 05 08_03a stays illegible enhanced (16 October 2026); every photograph has the plate in its ring and the GUB videos show it from above only. A photograph of its edge out of the ring would settle it. The section's print in Klassik Uhren 3/2006 (about 23 px/mm, 2.4 times the coloured scan, 31 October 2026) draws the pillar plate 3.33 and the top plate 3.51 on its 19.0 between the plates (the pillar 8.15 against its 8.1): the top plate's 3.35 is sure, so the drawing is good to about ±0.15 and can't tell 3.35 from 3.40. Lange 5395's movement out of its bowl (
breker_306_lange5395_3.jpg, 1000 px) shows the plate in its ring, not its edge. - Wempe 3955's seconds wheel (
8_…Räderwerk_plus.jpg) shows a raised ring Ø 6.4 ±0.3 on its train-side face (54 px against the tips' 188 for Ø 22.45, 8.37 px/mm: 16 October 2026), the sheet's hub Ø 6, so likely the hub proud on the face away from its pinion, where 05 05 01 draws it proud on the pinion's side (built as drawn: proud on the train side it would meet the intermediate pinion's end). The 6MX's wheel (6_Kirow_DEC_422_S) has its spokes running into a small boss about Ø 3.7 and no such ring. The wheel's other face or a side view would settle it. - The escapement of 1943's block against its sheet (17 October 2026; The escapement of 1943 above). Kirow DEC 422, DEC 479 and Lange 5177 all show the upright's slit parallel to the plate, along the banking screw, where 05 04 01-4 draws it upright and across the screw (the drawings' version as last revised built as the sheet since 28 October 2026; the 1943 version as the photographs). The slit shows 2.4-3.5 past the screw on them (the arm's length scales 16.5, 15.6 and 13.1 px/mm along it), against the sheet's 4.55 (7 from the end, the screw 2.45 in); the slit's end may fade before it stops, so the sheet's 7 is kept. The 6MX's upright is slit too (29 October 2026: Kirov 247 and Kirov-Poljot 24020), 2.8-2.9 from its end, into the screw's hole; the German slit reads longer on all three, so the two kept apart. A side view of a loose 1943 block, or one from its end, would settle both.
- The detent's level against the upright (17 October 2026). On the three German photographs the detent's blade and gold spring stand 0.7, 1.07 and 1.2 over the upright's top (DEC 479, DEC 422, Lange 5177; the blade's 0.9 checks DEC 479's scale). The head's top stands 0.6-1.1 under them. The sheets put the detent's lower face (3.3 under the plate, 05 04_1's 1.3-3.3) 0.2 over the upright (3.5, 05 04 01-4 in first angle), and the escapement of 1943 is built so, its head's top 0.15 under the detent. Either the photographed detent hangs about 0.5-1.0 higher than 05 04_1's "1,3" puts it, or the upright lower; DEC 479's base (6.5 deep, flush with the upright as drawn) reads the upright 3.8-6.7 under the plate (±0.3 with the camera). The screw's underside reads about 2.8-3.8 from the upright's near face on 5177 and DEC 479, the 6MX's loose block 2.8; drawn 2.28, where the model's pipe is. A photograph of the detent from its end, the plate's face in view, would settle the levels.
- The detent's banking and the detent's level: closed 27 October 2026 (Readings corrected: the 1946 staff). The block's side view is first-angle, as its sheet reads and every side photograph of the block in place has it (the 6MX's Kirow 92, KirPol 24020, Wempe 3955's 1941 block, Kirow DEC 422 and 479, Lange 5177; and Wempe No. 9166 of 1972: below), the upright 3.5-6.5 under the plate, the M1.2 banking screw 5.0 and the foot 1.35-3.25; the 1946 staff's rollers were misread, so nothing stands against those heights. Its setting, the detent's preload (Physics: in time): the 6MX's detent rests about 2° out of line with its foot toward its banking (a set spring), but no photograph shows its free line; the estimate is kept (Building it).
- 05 04_1's figures not identified (its 5°, beside the 6°, is read since 11 November 2026: Readings corrected; the 1° by the gold spring's tip likely with it): 20°, "1° – 1/8°", the elevation's 2.7 and 2.1, and its 2.3, 1.3 and 6.5 (the plate to the strip's lower edge, scaling 3.30, 1.31 and 6.54). The "0.9" is the "0,5" already corrected (Readings corrected). The sheet's impulse ends at the wheel's +10.5°, the stone's acting end at about r 3.365, where the model's SIMP 3.33 (05 04_6's 1.55 + 1.8) ends it about 9.9° and runs 2.6° on to the lock against the sheet's 2°.
- 1436's bracketed figures (above: taken as the revised sizes): the square's "(0,09)" bracketed alone, the "0,07" with faint brackets whose contents can't be read; the faint "0,18 u.d.f." beside the spring reads "v.d.f." or "v.d.h." (the third letter tall with a descender loop: f or a Kurrent h), its meaning unsettled. Its "4,4" (the horn to the pipe's centre, from the top line) is taken against the 5.2 its drawing scales: Wempe 3955's detent measures 4.4-4.55.
- 05 04_7.2's wheel seat: its callout reads 1.8 H7/h6, its fit table 1.7 (1.7 built). The callout's extension lines, drawn from the wheel's dashed bore, scale 2.0 apart (17.3-17.6 px/mm) and the table's +0.009/−0.007 fall in the same ISA range for both; the 1941 sheets give 1.8 (05 04_1's bore, 05 04_7.1's collet). The collet 05 04 10's own sheet would settle it.
- The swing, under the sources' band. No sheet gives the Einheits-Chronometer's own swing. The model's is 155.1-165.8° over the wind (160.7° at 12 h) since 11 November 2026, with the tooth let go where 05 04_1 has it (The discharge stone at 05 04_1's 5°); 188.5-199.5° until then, and before that as the dated figures in Physics record. The 1954 Soviet instruction gives 225-270° for chronometers in general: the model is 59-70° under it, and on 05 06_20's measured drive no damping the balance's parts allow reaches it (87-234 s of free run-down give 146-213° at 12 h; 225° wants 276 s). The cause is the late landing: the wheel, let go from rest with the stone already 5° inside the path, strikes it 4.9° before the line of centres and drives it through 12.3° of its turn, where the layout draws 21°. What could be off, each open: the drive's level (05 06_20's measured pull is 0.92 of the solved 0.37 strip's frictionless torque, and the band would want 1.72 times it at the wind's lowest); what the wheel must start at each beat (the train at 1.5 times its inertia costs about 3°, so not much there); the reading of the 5° (the period rule; the 1958 book's gap would let the tooth go later still and swing less); the damping (the model's 111 s is from a running 6MX on video, whose refit now gives 118 s, 105-129, and whose steady 149° the model now keeps on 87 % of its drive). Or the Einheits-Chronometer swung less than the instruction's chronometers.
wempe_escapement.jsandwempe_physics.jsreport it (~~), the owner's choice; the 147-270° check is only a guard against the model's own swing falling. The clicks of a running Lange VEB (gnIP3NqNbEU) and a Kirova (KxInG08LWXg), read with the escapement in time (acoustic.py --model wempe, not rerun since the stone's move:tools/acoustic_wempe.jsonis as it was), left the swing between readings 80-120° apart (which click is which isn't settled). - The drawn detent's ring, over half the depth of lock (11 November 2026; decided 12 November 2026, the estimate behind it open). With the stone at the sheet's 5° the frame (
tripping.js --model wempe) has a held tooth's stone ringing 53.9 % of the depth of lock as drawn, under half only from a preload of 0.93 g, over the 0.80 g at which the stone starts to land on the escaping tooth's back. No tooth gets past in any run with the preload on. By the half-depth rule the drawn version has no window for the lock (floor 0.254 mm, the deepest that unlocks 0.2436) or the preload. The owner's choice: the drawn versions are judged on no tooth getting past (the lock's floor 0.130 mm, where the frame last holds every tooth; the preload's 0.64 g, the knock's), the ring reported; the builds, with the gold spring thinned at its bend (their ring 51-56 µm), keep the half-depth rule on their own frame runs (wempe_build.js). Still open: the ring turns on one estimated contact stiffness (the discharge stone on the gold spring on the return,kR500 N/m: 3.4 % of the depth at a quarter of it, a tooth past at four times), the gold spring's alloy and free shape, and the preload, none of them drawn. Working that contact from its geometry (the stone's bevel on the spring's square end, the tip turning with the spring) would replace the estimate. - The 1958 book's gap at the discharge stone (Readings corrected, 05 04_1's 5°): 0.10-0.15 mm between the gold spring's end and the stone at rest, against the sheet's stone on the tip at rest. Not reconciled.
- The Soviet design and repair figures against the model (16 October 2026, recorded, nothing changed;
References/wempe/photos/catalogue-2026-10-16.md, each read again off the scans). Belyakov's Часовые механизмы (1957), Table 3, gives the 1st Moscow factory's MX-2 with "Lange's MX" in brackets (balance Ø 32.25, plate Ø 85); the Navy's Эксплуатация и ремонт измерителей времени (1958) gives the MX's assembly checks and plays. Which Lange the brackets describe (wartime or post-war) isn't said, and the drawings decide for the drawn chronometer; they bear on the readings below, and on the 6MX.- Agreeing: the wheel's 15 teeth, Ø 14 and 25° undercut; the balance's lift 42°18' (42° here); the detent spring 5.0 long and 2.0 wide (1436's 2, bracketed 1.9, built); the discharge circle r 1.55 (1.54-1.56 here); the hairspring's calculated length 502.35 mm in 12.78 working turns (505.4 pin to pin here, 05 03_7's 13 turns less 3.5 mm); the barrel's torque falling 1.84:1 over two days (1.81:1 here).
- The depth of lock: 05 04_1's 0.235 built since 19 October 2026 (the sheet re-scaled on the tips' Ø 14.00: The physics pass; 0.175 before), inside the 1958 book's check, the tooth onto the stone 0.20-0.25, and near Belyakov's linear lock 0.22 (Lange), 0.210 (MX-2); it unlocks to 0.247 (Building it; until then it unlocked only to 0.188, under them). But Belyakov's radii don't close with the centre distance for either chronometer as the models build it (the Wempe's wheel r 7 and impulse circle r 3.8 less the teeth's 0.39 into it make 10.41 against 05 04_1's 10.00; the Hamilton's Table 1, 6.575 + 3.70 − 0.3 = 9.98 against 9.40), so his linear figures may be measured another way (his "lock δ 1°" at the detent's locking arm, 14.25, is an arc of 0.25): settle how before using them.
- The detent spring's thickness: 1436's 0.07 (0.09 at its ends) built; Belyakov 0.05 at the bend, for both. Its stiffness hardly moves the swing (Building it); it moves the detent's ring and return.
- The gold spring's thickness: 05 04 01-2's 0.15 built (as the spring's section in the physics); Belyakov 0.06 (Lange), 0.05 (MX-2), at its bend; his Hamilton's 0.045. 0.06 would make it about 15 times softer, where half as stiff already lets a held tooth's stone ring 64 % of the depth of lock (
wempe_tripping.js; 51 % with the straight horn). The sheet's 0.15 may be the blank, thinned at the bend as a passing spring usually is: the most consequential of these. - The gold spring's reach: the 1958 book's check puts its end 0.35-0.40 past the detent's end, and at rest 0.10-0.15 short of the discharge stone (since 11 November 2026 see Readings corrected, 05 04_1's 5°: the sheet draws the stone on the tip at rest and is built); here the tip stands 0.056 past the horn's end radially (the horn 4.4 long), and on both photographed detents just past it along the horn (under 0.3). Different measures; not a clear disagreement.
- The impulse radius: 05 04_1's 3.35 built; Belyakov 3.8 (Lange), 3.435 (MX-2): see the depth of lock on his radii.
- Endshake: the 1958 book's MX: the fusee 0.08-0.12, the barrel, centre, intermediate and seconds 0.07-0.10, the escape arbor 0.05-0.07 (built 0.06, its middle, in every version since 25 October 2026, the 6MX's the book's own: 0.04 before), the balance 0.04-0.06 (side shake 0.005-0.03); the bench takes them since 19 October 2026 (0.01-0.08 estimated before; see Closed, Endshake).
- The mainspring's torque: the 1958 book's MX, 1.01-1.08 N·m fully wound and 0.55-0.60 two days on, against 839 and 427 mN·m here (824 and 473 with the free curve at ×0.6, until 26 October 2026) (the solved shape at 05 06_20's level); the later 6MX's strip is 0.42 × 14.8 × 1400 (Tarasov 1976) against 05 06_20's 0.37 × 15, so not the same spring.
- The stop work (P1c; full wind settled 15 October 2026, Readings corrected): N's undimensioned angle on 02-2 (only a leader to the groove's end) lies 0.07 turn past the model's groove end (0.08 along the axis); searched without result: Wempe 3955's train photograph (about 7 px/mm on the cover plate: the top land runs on unbroken along the front arc between the bar's two ends, the rest hidden by the arbor and the plate) and the GUB No. 12255 restoration, ZEc91vwppVk 3:19-3:55 (the fusee out in the hands; its small end only obliquely and blurred, at 3:34). Nothing works in the groove's last tenth of a turn, so it stays as built. The stop pin's length was scaled off the coloured section (1.85, the stop work). A GUB's fusee out (Ldzmn4kuKMA 1:13-1:17, the video review, 27 October 2026) shows the bar's end standing out of the top land as built, but it doesn't turn and the groove's end lies out of view. A fusee's small end opened would settle N (REQUESTS.md). Klassik Uhren 3/2006 (Lux and Petersen, p. 18) describes it as built: "eine Art Hebel durch die Kette betätigt, der gegen einen Begrenzungsstift in der Platine drückt" (31 October 2026).
- The mainspring's length to better than ±50 mm (P1c, 2b), and the barrel's 15.8 framed spring space (0207, 1941) against the 1948 drum's 14.95 (its level against 05 06_20 closed 26 October 2026: Closed). No 6MX document gives the spring's sizes or torque (6MX-figures.md), the gallery's "Feder" photographs are of the detent's spring, and Wempe 3955's laid-out spring (
14_Wempe_3955_Band_Kette.jpg) has no scale for its thickness; UhrenJust's GUB service (pbL64JZ-LGM 9:05-10:48, UG44DSWMv3o 0:00-6:46, 2160p, the spring out) or a measured 6MX spring might. For a made Wempe the free run-down test chooses the strip (Building it). UhrenJust's part 4 (UG44DSWMv3o 1:58-6:46) cleans the spring in its barrel and never takes it out (the catalogue said otherwise until 27 October 2026), so no video lays a spring straight. - The barrel arbor as last revised (05 07 02-1) isn't in the set (P1c): its diameters and core are fitted to the plates and drum; no photograph or video shows the arbor out.
- The hour wheel's collar (05 02 03's 5.2 against the 1943 cannon tube: above), and the seconds hand's height on the 1946 seconds post (the hour and minute hands are at 05 02_1's boxed figures since 28 October 2026): every dial photograph (Wempe 3955, Lange 5177, the Kirows) and GUB aQmO0UtXs24 0:00-2:10 is taken from above; a side view of the hands would settle it (none in any video: the video review, 27 October 2026).
- The long stud's end (05 08 02's Schnitt A-B at 2:1 draws it about 0.4 short of the plate's inner face, 2 px; 05 02_1 at 5:1, of the 1941 plate, to the face in a 45° sink, and the up-and-down pipe's heights agree with 12.3 from the face to 0.05): built to the face. No photograph shows the dial side in profile.
- The balance holding device (05 36), not built (the user's decision, 18 October 2026). How it works is Wempe's patent DE 742 143 (John Schwarzer, filed 26 November 1941,
References/wempe/documents/, figs. 1-4): two brass tongs (36 00 01-1, every figure) on one screw at hole 51 in the top plate's pocket, pressed shut by a leaf spring round them (the dark band 05 36's plan draws round their backs and bosses), close concentrically on a brake ring on the staff ("Bremsring aus Preßstoff", moulded phenolic: 05 36's Schnitt A-B draws it cross-hatched under the collar's flange, Ø 6.1 scaled, bore 2.6, its foot 0.2 under the plate's inner face; the plan's dotted ring Ø 5.85), so the balance stops without side load on its pivots; a bell crank (27, U 02) under the plate on a screw at 52, held by a coil spring to a pin at 53 against the flattened eccentric end of a knob's shaft in the case (28, U 03; the knob 1, turned 180° between "frei" and "fest", held by a spring and a detent pin), carries an upright pin in the tongs' notch, which spreads them open at "frei". Built in the version as first drawn on 18 October 2026 and taken out again the same day: drawn open, the tongs clear the impulse roller (the pocket, tapered 10 to 8 wide since 15 October 2026, lets each turn 3.8°, where the 8-wide pocket read until then allowed 0.8°), but the lever, traced on 05 36's plan put on holes 23, 51 and 52 (12.31 px/mm, 0.06 mm), runs 0.9 deep through the 1941 escape wheel (its teeth 0.5-1.9 under the plate, the lever 1.35 thick just under it: fine.py, 2.4 mm³) and grazes the 1941 detent (0.1), as it runs through the detent block of 05 04 01-4 (8.7.43) as last revised; and the 1946 hub has no ring where the tongs close (its neck Ø 2.63). 05 36 is drawn on the lever plate (its spring pin lands by the lever plate's hole 53, O 13.0, not the detent plate's, O 15.0) and 127-556 is the Luftwaffe's lever chronometer BC 1010 ("Unruh-Arretierung": Knirim; the hand setting, above): the device is that chronometer's, whose escapement (05 04_20, _21, 05 03_1) isn't built. No photograph shows one on a detent Wempe: Wempe 3955's plate has holes 51-53 empty (13_Wempe_3955_obere_Platte_unten.jpg), the 6MX uses transit dampers; Wempe 2965 (lever, "Anhaltevorrichtung") and 2900 (lever, "Arretierung des Werkes") were sold with one, not photographed in a way that shows it. The 1943 plate keeps the pocket and holes 51-53, so a detent chronometer may have had one, its form not in the set. - The case (P1f; the sources read again 16 October 2026, the 6MX gallery among them):
- The bowl's "Gewicht 350 gr.": the casting as drawn is about 152 cm³ (05 01_2's section: the wall 4, the bottom 6.5), 1.34 kg in brass (
gimbals_wempe.json); 350 g is 2.3 g/cm³, which no moulded case reaches (Buna or Bakelite 180-210 g, a mineral-filled phenolic about 300) and an aluminium casting only nearly (about 380 machined), and "Ms-Sandguß (Kokillenguß)" names a metal casting. Wempe 3955's Bakelite bowl (16_Wempe_3955_Gehäusetopf_Kardan.jpg) is beaded and rounded, not R-05 01 00-1's 40° cone: an undrawn bowl. The 6MX's TU gives the whole chronometer ≤ 2.2 kg (6MX-figures.md, TU 1.2.8), where the model's bowl and ring alone weigh 3.26 kg: if the TU's mass leaves out its box, the bowl would be about 280 g, near the sheet's 350 (moderately sure the brass bowl is too heavy; whether the TU's "масса" counts the box isn't said). The machined bowl's sheet (05 01 00-1 without the R-) would settle it. Klassik Uhren 3/2006 lists "Gehäusetopf und Kardanaufhängung aus massivem Messing" among the Kal. 05's features, and plastic bowls and gimbal rings among the economies ordered at the end of 1942 (with printed aluminium dials and the plates' ringing left off), which bears out a metal casting as drawn; it doesn't settle the 350 g (31 October 2026). - The bezel: screwed onto the bowl (likely): Wempe 5377's bezel is knurled at its lower edge (
bonhams_26816_327_wempe5377_type05.jpg, sure; its case later), Wempe 3955's edge serrated (moderately), Wempe 8711's "threaded glazed bezel" (Antiquorum's text, catalogue-de-en.md), and 05 01 01 draws a thread's zigzag hidden in the lower bore (about 3 teeth over 4.4: likely); the 6MX's bowls (KirPol 24020,leben-des-6mx/13_,14_KirPol_24020_E-Kontakt*.jpg; Kirow 24712_Kirow_247_E-Kontakt_3.jpg) have a thin threaded collar at the top, about 5 turns at about 1 pitch, the ring's flange on a step inside it. The thread isn't sized on any sheet: built since 24 October 2026 at the 6MX's size and pitch (the bowl's rim turned down to it: The bezel and glass). - The ring's pin: no notch (05 01 01 draws the bezel without one; a notch in the bezel at 12, estimated, was built until 21 October 2026). A screwed bezel can't hold a notch to the pin, and KirPol 24020's bowl has the notch cut down through its threaded collar at 12 o'clock, about 1.6 wide and 4-5 deep (sure for the 6MX); so the Wempe's is likelier in the bowl, but 05 01 01 lays the flange in the bezel's recess, above the bowl's top face, where only the bezel meets the pin. With the bezel built to 05 01 01, which also marks its lower bore threaded, the pin stands clear: its seat, likely in the machined bowl, isn't drawn.
- The Feststeller: on Wempes 4585 (
rmg_L5393_wempe_wartime_001.jpg) and 5377 a knurled knob about Ø 20-21 on a short post, on a flat lever on a block on the right wall, with an upright pin about Ø 4 on the lever between the knob and the ring, where Schnitt A-B draws a circle Ø 8.6 under the lever (built Ø 8, as the sheet); the knob's top about 10 (5377) and 17-19 (4585) over the lever against the model's 15.3 (rough readings in perspective; the "17" from the front wall agrees). A side-on photograph of a Wempe's lock with the ring in place would settle the heights. Wempe 3044 (milivault_529241_wempe3044_screen.png, from above, rough) has the pin's round head, Ø 8.7 ±1, slotted, built Ø 8.7 × 2.5 on the drawings' case (its height estimated; the 6MX's pin kept plain), its lock's bracket a black block about 20 wide (the model's seat 18, kept), and its lever about 45 long along the front wall against 05 01's 28 (kept: the sheet decides; it may be another lever). Lange 5591 (delivered 16 March 1945; Angerland, lot 576,angerland_576_lange5591.jpg, 4000 px from above, 31 October 2026): a knurled black knob on a hub, the lever on a black block in the box's front right corner, and the upright pin with a domed round head about halfway out, as the wartime one is built; its plan places read only roughly (the knob's own Ø the scale, an estimate itself: the pin's head about Ø 4.5 and about 12 from the knob's axis, against the model's 14.0, ±1, not adopted). Its heights need a side view still. - The Zunge (P. 51 00 02-2): on Wempes 4585 (aluminium) and 5377 (brass) the box's latch is an angle plate at the front's middle on the body, its top flange slotted about 6.5 long, with a knob about Ø 7 beside the slot, and an angle plate on the lid with a C-shaped hook into that slot; the model's tongue swinging on the lid's front over a keeper doesn't match. The Zunge (iron 10 × 4, 45 long, the M3.5 for a knob, a thinned round end) fits as the bolt behind the body's plate, which the knob moves to catch the hook (inferred); how it moves isn't seen. The 6MX's boxes have escutcheon hasps instead. Lange 5591's box (
angerland_576_lange5591.jpg, 31 October 2026) has the same angle plate on the body's front, centred on it: 43.9 ±0.5 long (scaled on the body's 185 at its top edge, 10.3 px/mm), its top flange with two slots, 8.1 wide 6.6 left of its middle and 3.4 wide 11.7 right of it, two screws on top 36.7 apart and two in its face, and a round knob about Ø 9 ±0.5 on its face under the slots (likely); a Lange's, read from above, so the slots' depth and the hook aren't seen. Built so since 31 October 2026 (the owner's choice: Estimated, the latch): the latch plate and the lid's hook plate as measured, the tongue out of view behind the plate; it stays here for the tongue's arrangement and the plates' depths, which a side view of an opened Wempe or Lange latch would settle. - The box's height (25 October 2026, decided, nothing changed): 05 01's note gives "Holzgehäuse 185 × 185 × 180 mm außen" (sure); 51 00 10 ("Änderung von 51 00 10", gez. 14.7.42) draws the side panel square, 185 wide (±0.5) and 185 high (both figured; the outline 436 × 437 px at 2.38 px/mm), with the pivot's M6 105 over its bottom and the parting line 11.5 over that, so the same box. 05 01 was drawn 30.10.40 and reissued unchanged as working copy 4 (28.6.46, stamped 31.3.47), so its 180 is both the earlier figure and the latest one issued; the handle's sheet is a change to the handle, its panel drawn round it. Kept 180 in every drawn version: the 185 would only make the lid 5 taller (68.5 over the parting line against 63.5), the parting line, the pivots and the gimbals where they are. A measured height of a 1940s Wempe box would settle it (Lange 5499's auction gives 183 × 172 × 180, another maker's box, its axes not named). Two Lange lots of the war give theirs as 18.5 × 18.5 × 18.5 cm (No. 5644, Hanseart Lübeck, lot 892) and 18.5 × 18.5 × 18 cm (No. 5389, Cortrie): recorded, 180 kept (31 October 2026).
- The pins over the outer pivots (25 October 2026; built, Estimated): 05 01's elevation alone draws them, without a number or part line, inside drawn in crossing coils (a thread or a spring); no photograph shows one (Greenwich's wartime Wempe's side walls' tops over the pivots plain at about 2.5 px/mm, Wempe 6161's box later, with a rebated lip). Whether they locate the lid, catch it (a ball catch) or are something else isn't settled; a photograph of a 1940s box's parting face, or the box's own sheet (127-556.02), would settle it. Klassik Uhren 3/2006's list of the Kal. 05's features gives the box "Deckel abnehmbar" (its words; whether these pins are how it lifts off isn't said: 31 October 2026).
- The Holzkasten's own sheet (127-556.02) isn't in the set; 127-556.02 U 01 (05 01_6, parts -01 to -05) is the 1940 key; the 1943 key is 51 00 11 (05 01_7), its parts 51 00 11-1 to -6 and 05 01 02-2, -3; each fits the holder in the box (the second drawing check's 10-M13).
- The bowl's "Gewicht 350 gr.": the casting as drawn is about 152 cm³ (05 01_2's section: the wall 4, the bottom 6.5), 1.34 kg in brass (
- The escape wheel's web recess against its teeth's floor (25 October 2026,
dfm.py; Making it): the recess Ø 11.62 (05 04_7.2 scales 11.65) lies 0.04 inside the 1942 tooth form's floor Ø 11.7, leaving a sliver of brass about 0.04 wide and 0.6 high in each gap, which no maker would leave; built as the sheets give it. A sheet giving the recess's diameter as a figure would settle it.
What the tools flag
Every ~~ the checks above print, together: what they report without failing on.
Reproduce
From marine-chronometer-source/wempe/verification/:
node reportdata.js # every Wempe check run (the full runs, at once), and the figures: assets/data.json (about 9 minutes) python geometry.py # the browser checks on the Wempe's page, one after another: assets/geometry.json (about 11 minutes; section 19's fea, assembly and dfm about 16 more, each also writing its own JSON in assets/) python build_report.py # this page, index.html (a second)
Each tool can be run on its own from marine-chronometer-source/chronometer-working-model/tools/ (the commands are beside each tool's checks above). The
model's ci.py runs the quick forms of all of them on every change, and the full runs with --full, but three: the readings off the videos
(wempe_swing.py, acoustic.py --model wempe), which need the videos, and the start-up fit made on them (wempe_startup.js), whose result
wempe_escapement.js checks the model's damping against. This page is rebuilt when their results change.
Scripts
| Script | What it does |
|---|---|
solids.py, fine.py, audit.py, exploded.py, bom.py | The geometry checks, the Wempe's tables in wempe/checks.py, bom.json and audit-expected.json (section 1) |
wempe_escapement.js | The escapement as makeEsc solves it, the drive, the damping, the swing and rate over the wind (3.1) |
dynamics.js | The escapement in time (3.2) |
tripping.js, wempe_tripping.js | The detent as a frame of beams (3.3) |
wempe_mainspring.py | The mainspring solved and fitted to 05 06_20; its coil friction (4) |
wempe_physics.js | The energy budget (5) |
gearing.js, wempe_train.js | The meshes tooth by tooth (6) |
wempe_strength.js | The parts' strength (7) |
wempe_hairspring.js | The hairspring (8) |
wempe_thermal.js | Temperature (9) |
wempe_thermal_frame.js | Temperature (9) |
massprops.py, gimbals.js, wempe_gimbals.js | The case and gimbals (10) |
wempe_errorbudget.js | The TU's trial and the voyage (11) |
wempe_navigation.js | Made chronometers carried to sea, their longitude error and the fix's (21) |
wempe_tolerances.js, wempe_bench.js, wempe_montecarlo.js | The tolerances, the bench's tests, the movement made to tolerances (12) |
wempe_transmission.js | The whole transmission in time, every part that moves (13) |
keystone.js | The escapement against the 1904 text (14) |
wempe_swing.py, wempe_startup.js | The swing read off a video and fitted (15) |
wempe_wear.js, wempe_overwind.js, wempe_motionwork.js, wempe_estimates.js | The mechanisms in turn: wear, the key forced, the motion work and its studs, the estimates swept (18) |
fea.py, assembly.py + assembly-check.js, dfm.py | The frame under load, the order of assembly, each part on the machine (19) |
wempe_makers.py, book.py | The maker's sheets' data, and the build book checked as paper (20) |
reportdata.js, geometry.py, build_report.py | This page's data and the page |
Sources
The model's sources, as its README gives them:
- The works drawings,
References/wempe/drawings/(© Johannes Altmeppen, by courtesy of Gerhard D. Wempe KG, 2017), as transcribed inReferences/wempe/transcriptions/05-08-frame.mdand checked on the sheets themselves, cropped and enlarged wherever a number mattered. The frame's sheets are 05 08_1a/1b (Oberplatte, 05 09 01), _2 (Oberplatte kompl., 05 08 01), _3a/3b (Unterplatte, 05 08 02-1), _32.2 (Unterplatte kompl., 05 08 02), _4 (Unruhkloben unten, 05 08 00-2), _5 and _6 (Unruhkloben oben, 05 08 03-1, and the kompl. 127-556.04 U30), _7 (Werkring, 05 08 00-3), _8 (Schneckenfutter, 05 08 01-2), _9 (Staubfutter, 05 08 01-3), _10 (Zwischenbrücke kompl., 05 08 04), _11 (Pfeiler, 05 08 00-1), _12 to _14 (Federhausbrücke kompl., 05 08 05; Federhausbrücke, 05 08 05-1; Sperrkegel, 05 08 05-2), and sheet 001 (the movement in plan at 2:1). - The coloured section (
drawings/Wempe_Einheitschronometer.jpg): the whole movement in one unrolled section, with the parts' numbers, including the Wempe standard parts (WN) that have no sheet in the set. Measured on it where no sheet gives a size, scaled on the pillar's 8.1 and the 19 between the plates (28.3 px/mm in a 3× crop, the same both ways where it was checked). - Photographs of genuine German movements: Wempe 3955 above all (
photos/dg-chrono-dec/):2_Wempe_3955_A.jpg, the top plate square-on on millimetre paper (8.82 px/mm at the plate, from the pillar screws' 62.41 and 58.7 mm apart);3_Wempe_3955_uZ.jpg, the dial side;12_and13_Wempe_3955_obere_Platte_*.jpg, the top plate off, both faces; the side views4-7_Wempe_3955_*.jpg. ALS 5177 and the Kirow movements likewise. The 6MX differs (seeReferences/wempe/README.md) and isn't evidence for the frame. - The 6MX's test cards (
photos/dg-chrono-6mx-gallery/bilder-zum-6mx/: eight passports and attestats of Soviet 6MXs, 1953-1993, transcribed inReferences/wempe/documents/6MX-figures.md, section 8): the scatter and drift and the masses' setting the trial is run with, and the check on its secondary error. - National Bureau of Standards, Circular 58, Invar and related nickel steels (2nd ed., 1923), Tables 5 (p. 86) and 13 (p. 90): Guillaume's nickel steels' expansion, a + 2bt, by their nickel; the rim's 42-44.4 % "anibal" quadratic −3.4 to −2.51 × 10⁻⁹ a °C² (
tools/wempe_thermal.js). - M. Lux and C. Petersen, "Das Einheitschronometer", Klassik Uhren 3/2006, pp. 16-24 (31 October 2026; the PDF on glashuetteuhren.de's Kal. 100 page, https://www.glashuetteuhren.de/kaliberuebersichten-modelle/a-lange-soehne/einheitschronometer-kal-100/, not kept in the repository): the Wempe works' history of the Kal. 05, its features listed, the wartime economies, and the general arrangement "Federchronometer 05" printed across pp. 16-17 (the coloured section's drawing in black and white, about 23 px/mm at its scan's 280 dpi, its labels legible where the coloured scan's aren't). Read for labels and arrangement, not sizes (it draws the top plate 3.51 against the sure 3.35). The same page lists Lange's changes by serial: three pillars, Bakelite bowl and gimbals, "Federhausdeckel unten", the fusee's height 12.2 (Kal. 100's 11.4), the motion work's 7 (the model's: the dial 7 over the pillar plate), the movement ring's 104 (the model's recess Ø 104.05), gilt train wheels from No. 5091, a heavy bottom weight from 5100, the balance 3.8 high from 5111 (the rim's 3.8 built), the "Gegenfeder" changed in Glashütte from 5201, and "eine neue Gangfederstellung" (the detent's) against Kal. 100's foot spring. Also in the article (1 November 2026; recorded, nothing changed by it): its features list (p. 18) gives two days' going with the 56-hour up-and-down work, the plates of brass "geringelt" (the damascening, which the wartime economies of late 1942 sometimes left off, p. 19, with printed aluminium dials and plastic bowls and gimbal rings), the Guillaume balance of "hochwertigem Chrom-Nickel-Stahl", the dial "95 mm Durchmesser, aus 1,3 dickem Messing, mattversilbert" with its figures engraved and filled black (the Dial item below), the hour and minute hands gilt, and the box mahogany or oak with a lid that lifts off; the chain then the band (References/wempe/README.md's Unsettled); the designers Herbert Müller and John Schwarzer (Schwarzer's balance holding device patented 1941, p. 21, as 05 36 and DE742143); Kaliber 04 the lever version, 05 the detent's. Its serial tables (pp. 22, 24): Wempe's Einheits-Chronometer from No. 2800 in 1942 (the last of the earlier model 2781), the highest number each year (1942 3019, 1943 3452, 1944 4338, 1945 4919; after the war 1946 5138 to 1965 7680, from 1966 by year), lever chronometers on the Einheits base about 2600-3000 and numbered with the rest, Lange's from 5001 (31 March 1943) to 5870 (1947); the 6MX made in Moscow until 1997. The essay's rule against serial ranges (CLAUDE.md) predates this source and is left as it stands.
And for the methods:
- Хронометры морские 6МХ. Технические условия, TU 25-07.1533-84 (1st Moscow Watch Factory): the trial and its limits; Instruction 246-54 for checking standard chronometers (1954): the swing for chronometers in general, the banking, the start.
- V. A. Shpolyanskii and A. M. Kuritskii, Spuskovye regulyatory priborov vremeni (Moscow 1963): marine chronometers' balances, the 6MX's integral balance and banking screw.
- E. Phillips, "Mémoire sur le spiral réglant des chronomètres et des montres", Annales des Mines (1861): the terminal curves' conditions.
- S. Timoshenko, "Analysis of bi-metal thermostats", Journal of the Optical Society of America 11 (1925): the bimetal's curl.
- National Bureau of Standards, Circular 58, Invar and related nickel steels (2nd ed., 1923), Tables 5 and 13: the nickel steels' expansion by their nickel, the secondary error's quadratic.
- C.-E. Guillaume, Nobel lecture (1920), and VintageWatchstraps, "Temperature Compensation by Nickel Steels": the nickel steels and the integral balance's secondary error at the Neuchâtel trials.
- M. A. Crisfield, Non-linear Finite Element Analysis of Solids and Structures, vol. 1 (1991), ch. 7: the co-rotational beam element; J. S. Przemieniecki, Theory of Matrix Structural Analysis (1968): the frame element and its consistent mass; P. Wriggers, Computational Contact Mechanics (2006): penalty contact.
- NORDFORSK, Assessment of Ship Performance in a Seaway (1987): the operability limit; MARIN (IMDC 2024) and Jachowski et al., KONES (2012): merchant ships' roll periods.
- J. F. Archard, "Contact and rubbing of flat surfaces", Journal of Applied Physics 24 (1953); E. Rabinowicz, Friction and Wear of Materials (2nd ed., 1995): the wear law and its coefficients. A. Imrhan and C. Munoz-Vasa, Industrial and Systems Engineering Review 1(2) (2013), and Swain et al. (1970): a hand's torque on small handles. EN 10270-1: patented cold-drawn spring wire's strength.
- Mainspring friction and losses: ICMFF9 (gruppofrattura.it), "the torque during unwinding is 10 to 20 per cent less than that during winding"; lubricated steel on steel, the CRC Handbook as cited in US 3,939,081.
- The Hamilton's reports, whose tools these are: Would a chronometer made to the model run and keep time? and Does the model behave like a real Hamilton Model 21?
The scripts' outputs that feed this page are embedded in it, so it opens from the file. Built by build_report.py; do not edit index.html by hand.